• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.909-914
• /
• 2001

After burner which is main part of inert gas generator(IGG) is studied for the development of IGG. The results of many experimental equations are applied to estimate characteristics of the spray nozzle and evaporation of spray, and selected the optimum design point of after burner. The selected design point of after burner are validated experimentally through the pilot plant of after burner. The flame stability is favorable at design point(150mm), that distance from stabilizer to nozzle. The emission of $NO_x$ and CO is lower than gas turbine combustor which was used in primary combustor.

• Journal of the Korean Society of Visualization
• /
• v.20 no.3
• /
• pp.117-127
• /
• 2022

The present study has investigated the performance of hydrogen gas generators for inhalation purposes based on polyelectrolyte membrane water electrolysis (PEMWE). The system applied two watering methods. One is pumped water (pumping system) and the other is gravity-fed water without a pump (non-pumping system). The cell efficiencies were compared by measuring the cell voltage and temperature in the hydrogen gas generator, respectively. The results show that the cell voltage and temperature increase with the cell current. The cell temperature is lower in the pumping system than that in the non-pumping system at a given cell current. Even though the amount of hydrogen production is the same regardless of the pumping system, the cell efficiency of the hydrogen gas generator in the non-pumping system is better than that in the pumping system.

• The KSFM Journal of Fluid Machinery
• /
• v.17 no.3
• /
• pp.19-24
• /
• 2014

Development of long-term mobile energy sources for mobile robots or small-sized unmanned vehicles are actively increasing. The micro gas turbine generator (MTG) is a good candidate for this purpose because it has both of high energy density and high power density, and 500W class MTG is under development. The designed MTG can be divided into 2 main parts. One part consists of motor/ generator and compressor, and the other one consists of combustor, recuperator and turbine. 500W class MTG is designed to operate at ultra-high speed of 400,000 rpm in high turbine temperature over $700^{\circ}C$ to improve the efficiency. Because the magnetism of NdFeB permanent magnet for the motor/generator could be degraded if the temperature is over $150-200^{\circ}C$, MTG needs the thermal insulation to block the heat transfer from combustor/turbine side to motor/generator side. Moreover, the motor/generator is allocated to get the cooling effect from the rapid air flow by the compressor. This study presents the experimental results to verify whether the thermal insulator and air flow are effective enough to keep the motor/generator part in the low temperature less than $100^{\circ}C$. From the motoring test by using the high temperature test rig, it was confirmed that the motor/generator part could maintain the temperature less than $50^{\circ}C$ under the condition of 1.0 bar compressed air.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.109-112
• /
• 2001

Water-Electrolyzed gas is a mixed gas of the constant volume ratio 2:1 of Hydrogen and Oxygen gained from electrolyzed water, and it has better characteristics in the field of economy, efficiency of energy, and environmental intimacy than acetylene gas and LPG (Liquefied Petroleum Gas) used for existing gas welding equipment. So studies of Water-Electrolyzed gas are activity in progress nowaday, and commercially used as a source of thermal energy for gas welding in the industry. The object of this paper is getting a V-I characteristic of Hydrogen-Oxygen Gas Generator using DC source. First, chemical analysis of electrolysis is conducted and the relation of electrical energy and then chemical energy is investigated through the faraday's laws.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2005.11a
• /
• pp.207-210
• /
• 2005

The results of combustion performance test of fuel-rich gas generator with dual swirl injectors are described. By changing simulating duct and recess number(RN) of the injectors, we inspected whether the combustion instability took place. When the injectors of RN = 0.5 were used, combustion instabilities could be reduced using the simulating duct. However, the effect of the simulating duct on the gas generator with the injectors of RN = 1.5 was not significant.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.413-416
• /
• 2009

For the liquid rocket engine, the gas generator oxidizer shut-off valve which supplies the oxidizer to a gas generator needs structural safety under the internal pressure, which is higher than the chamber pressure. In this study, static stress analyses of the various design in the vicinity of the region where the stress is concentrated were performed for designing the lightweight valve, A lightest model of which the concentrated stress does not exceed the yield criteria has been suggested. Also, whole size effect of the valve on the concentrated stress was investigated.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.726-728
• /
• 2010

A subscale gas generator was designed and manufactured to investigate the effect of design parameters on discharge coefficients of injectors for a 75 ton-class gas generator and hot-firing tests were successfully performed. The test results showed that discharge coefficients of fuel and liquid oxygen injectors remained nearly constant irrespective of variations of a mixture ratio and a chamber pressure. When the post diameter of the liquid oxygen injector was reduced, the discharge coefficient was increased as the pressure drop of the injector was decreased.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.565-568
• /
• 2010

A pressure control law to regulate mass flow rate of gas generator is suggested. The governing equation is modeled by considering the burning rate of solid propellant and the conservation equation of gas generator. And then, a classical control law is applied after verifying the accuracy of dynamic model through comparing with ground test and internal ballistic results. The results show degradation of performance as shown in typical time varying system. To overcome this problem, an adaptive scheme is suggested and the performance is verified through numerical simulation.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.173-176
• /
• 2010

A subscale gas generator was designed and manufactured to understand a reason for increased pressure drop of liquid oxygen injectors observed in a technology demonstration model of a 75 ton-class gas generator. A total of 6 hot-firing tests were successfully performed including experimental conditions of design and off-design points. The hot-firing results showed that discharge coefficients of fuel and liquid oxygen remained constant as the mixture ratio varied at a fixed chamber pressure. At a fixed mixture ratio, it was also found that discharge coefficients of fuel and liquid oxygen was constant as the chamber pressure was increased.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.1084-1087
• /
• 2017

When a liquid rocket engine is started the oxidizer and fuel must be flowed into combustion chamber and gas generator with time differences. The wrong time difference between propellants or malfunction of ignition device can occur the explosion of combustion chamber due to detonation by energized premixed-propellants. Therefore it is important to observe the transient characteristic of propellants or to measure the inflow time of propellants into combustion chamber and gas generator. The measurement of static pressure is not enough to observe the propellants inflow time into combustion chamber and gas generator. By measuring dynamic pressure of main flow passage of propellants the accurate propellants inflow time could be investigated.