• Journal of Hydrogen and New Energy
• /
• v.30 no.3
• /
• pp.282-288
• /
• 2019

When liquefied natural gas (LNG) is vaporized to form natural gas for industrial and household consumption, a tremendous amount of cold energy is transferred from LNG to seawater as a part of the phase-change process. This heat exchange loop is not only a waste of cold energy, but causes thermal pollution to coastal fishery areas by dumping the cold energy into the sea. This project describes an innovative new design for reclaiming cold energy for use by cold storage warehouses (operating in the 35 to $62^{\circ}C$ range). Conventionally, warehouse cooling is done by mechanical refrigeration systems that consume large amounts of electricity for the maintenance of low temperatures. Here, a closed loop LNG heat exchange system was designed (by simulator) to replace mechanical or vapor-compression refrigeration systems. The software PRO II with PROVISION V9.4 was used to simulate LNG cold energy, gas re-liquefaction, and the vaporized process under various conditions. The effects on sensible and latent heats from changes to the array type of heat exchangers have been investigated, as well as an examination of the optimum.

• Journal of Hydrogen and New Energy
• /
• v.35 no.3
• /
• pp.290-299
• /
• 2024

In this study, a theoretical study was conducted on the pre-cooling temperature of hydrogen gas and the heat exchanger area in a small-scale liquefied hydrogen system. The small-scale liquefaction system was built and liquid hydrogen production experiments were performed. In this process, the temperature of precooled hydrogen gas was measure to be about 120 K, and then the possibility of a cause was analyzed through pressure analysis of hydrogen gas and container, and analysis of the amount of liquid hydrogen produced. It was found that some reasonable results were obtained from the theoretical approaches. Based on this theoretical approach, we aim to improve the production of liquid hydrogen by optimizing the heat exchange area according to flow rate.

• Journal of the Korean Institute of Gas
• /
• v.8 no.2 s.23
• /
• pp.28-34
• /
• 2004

Enhanced methodologies for process diagnosis and abnormal situation management have been developed for the last two decades. However, there is no single method that always shows better performance over all kinds of diagnostic problems. In this paper, a framework of message-passing, cooperative, intelligent diagnostic agents is presented for improved on-line fault diagnosis through cooperative problem solving of different expertise. A group of diagnostic agents in charge of different process functional perform local diagnoses in parallel; exchange related information with other diagnostic agents; and cooperatively solve the global diagnostic problem of the whole process plant or business units just like human experts would do. For their better understanding, sharing and exchanging of process knowledge and information, we also suggest a way of remodeling processes and protocols, taking into account semantic abstracts of process information and data. The benefits of the suggested multi-agents-based approach are demonstrated by the implementations for solving the diagnostic problems of various chemical processes.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.1 no.1
• /
• pp.80-89
• /
• 1993

Performance simulation for a Spark Ignition Wankel rotary Engine is presented in this paper. The volume of chamber at each eccentric shaft angle is evaluated by using geometric models of housing and rotor. A thermodynamic model which includes the first law of thermodynamics, combustion and convective heat transfer from chamber contents to surroundings is imployed. A thermochemical equilibrium model which considers 10 species(CO, $CO_2$, $O_2$, $H_2$, $H_2O$, OH, O, NO, $N_2$) in the burned gas region, is also employed. Four processes of gas exchange, compression, combustion and expansion are considered and the pressure, temperature and composition of chamber gas at each eccentric shaft angle in each process are computed in this performance simulation. This performance simulation must be useful for optimal design of Spark Ignition Wankel Rotray Engine with parametric study for various design parameters and operating conditions.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.81.2-81.2
• /
• 2011

The gas diffusion layer (GDL) consists of two main parts, the GDL backing layer, called as a substrate and the micro porous layer (MPL) coated on the GDBL. In this process, carbon particles of MPL penetrates to the GDBL consequently forms MPL penetration part. In this study, the micro porous layer (MPL) penetration thickness is determined as a design parameter of the GDL which affect pore size distribution profile through the GDL inducing different mass transfer characteristics. The pore size distribution and water permeability characteristics of the GDL are investigated and the cell performance is evaluated under fully/low humidification conditions. Transient response and voltage instability are also studied. In addition, to determine the effects of MPL penetration on the degradation, the carbon corrosion stress test is conducted. The GDL that have deep MPL penetration thickness shows better performance in high current density region because of enhanced water management, however, loss of penetrated MPL parts is shown after aging and it induces worse water management characteristics.

• Applied Chemistry for Engineering
• /
• v.32 no.2
• /
• pp.149-156
• /
• 2021

A kraft recovery boiler produces steam for power generation by the combustion of black liquor from the kraft pulping process. Since saturated steam became superheated in a superheater above the furnace, it is important to increase the heat exchange efficiency for the superheated steam production and power generation. A nose arch at the bottom of the superheater is important for blocking radiation from the furnace which causes corrosion of the superheater. But the nose arch is the main reason for creating a recirculation region and then decreasing the heat exchange efficiency by holding cold flue gas after the heat transfer to saturated steam. In this study, the size of recirculation region and the temperature of flue gas at the outlet were analyzed by the nose arch structure using computational fluid dynamics (CFD). As a result, when the nose arch angle changed from 106.5° (case 1) to 150° (case4), the recirculation region of flue gas decreased and the heat exchange efficiency between the flue gas and the steam increased by 10.3%.

• Journal of the korean Society of Automotive Engineers
• /
• v.9 no.4
• /
• pp.77-85
• /
• 1987

본 논문은 단기통 4사이클 전기점화기관에서 가스교환 과정이 체적효율에 미치는 영향에 대하여 연구한 것이다. 가스교환 과정의 수학적 모델을 설정하고 수치해석을 수행한 결과 체적효율은 가스교환과정과 관련되는 밸브 개폐시기(1,2)보다는 흡배기관의 압력에 의하여 더 큰 영향을 받는 다는 것을 알 수 있었다. 실험에 있어서는 각각 밸브 개폐시기가 다른 3종류의 캠을 사용하였 으며 수치 해석결과와 실험결고가 비교적 잘 일치하였다.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.351-351
• /
• 2000

Since the heat exchange system, such as the boiler of power plant, gas turbine, and radiator require an application of intelligent control system for a high rate heat efficiency and the efficiency of these systems is depended on the control methods it is important for operator to understand control system of these systems and intelligent control technologies. In order to properly apply control equipment and intelligent technology to these process control systems, it is necessary to understand fuzzy, neural network, genetics, and immune as well as the basic aspects and operation principle of the process that relate control, interrelationships of the process characteristics, and the dynamics that are involved. Generally, since PID controllers are used in these systems it is difficult far engineer to understand both the complex dynamics and the intelligent control method. In this paper, we design an effective experimental system for the intelligent control education and analyze its characteristics through experimental system and each intelligent method to study how they can learn intelligent control system by experiments.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.3
• /
• pp.291-298
• /
• 2010

A conventional EGR cooler, which is used in an EGR system of an automobile diesel engine, has a low heat-exchange efficiency. To maximize the heat transfer between the exhaust gas and coolant, dimples are formed on the surface of heat exchange tubes. When designing the dimpled EGR cooler, the net heat transfer areas in the conventional and dimpled tube-type EGR coolers are compared. Structural integrity evaluations are also performed by combining finite element analysis with a homogenization method. Subsequently, the process of manufacturing the dimpled tube, i.e., the formation of dimples, edge bending, center v-notch bending, compression, and plasma welding, is established and carried out. Thus, the dimpled EGR cooler is developed, and its performance is verified.

• Korean Journal of Optics and Photonics
• /
• v.11 no.3
• /
• pp.202-205
• /
• 2000

One step thermal potassium ion exchange process was carried out to form optical channel waveguides in an ErNb co-doped phosphate glass. Flowing oxygen gas into KN03 melt during ion exchange was effective to prevent glass surface damage that causes an increase of waveguide propagation loss. Amplification characteristics of the waveguides were evaluated at $1.5{\mu}m$ signal wavelength with 980 om laser diode pump. A 45 mm long waveguide whose processing parameters had been optimized exhibited a small signal net gain of 7.5 dB at the launched pump power of 160 mW.160 mW.