• 한국분무공학회지
• /
• 제27권4호
• /
• pp.181-187
• /
• 2022

For carbon neutrality, direct-injection hydrogen engines are attracting attention as a future power source. It is essential to estimate the transient injection rate of hydrogen for the optimization of hydrogen injection in direct injection engines. However, conventional injection rate measurement techniques for liquid fuels based on the injection-induced fuel pressure change in a test section are difficult to be applied to gaseous fuels due to the compressibility of the gas and the sealing issue of the components. In this study, a momentum flux measurement technique is introduced to obtain the transient injection rate of gaseous fuels using a force sensor. The injection rate calculation models associated with the momentum flux measurement technique are presented first. Then, the volumetric injection rates are estimated based on the momentum flux data and the calculation models and compared with those measured by a volumetric flow rate meter. The results showed that the momentum flux measurement can detect the injection start and end timings and the transient and steady regimes of the fuel injection. However, the estimated volumetric injection rates showed a large difference from the measured injection rates. An alternative method is suggested that corrects the estimated injection rate results based on the measured mean volumetric flow rates.

• 한국분무공학회지
• /
• 제27권2호
• /
• pp.94-100
• /
• 2022

Even in non-road UTV (Utility Terrain Vehicle), spark ignition engines are often used to reduce emissions. In this study, gasoline and LPG (Liquified Petroleum Gas) fuels were applied to UTV engines, and the exhaust gas and combustion stability were compared through engine tests. A 0.8-liter two-cylinder SI engine was used in the experiment. Experiments were conducted while changing the IVO (Intake Valve Open) and EVC (Exhaust Valve Close) at 1500 rpm 14 N·m, 40 N·m, and 3000 rpm 17 N·m, 44 N·m conditions. As a result of the experiment, when the valve overlap increased according to the change of IVO and EVC, combustion stability decreased and THC emission increased, but NOx decreased. Comparing the LPG engine with the gasoline engine, the amount of CO₂ and PN (Particulate Number) generation decreased in the LPG engine, and the combustion stability was good.

• 한국분무공학회지
• /
• 제27권1호
• /
• pp.1-10
• /
• 2022

In this study, an experimental investigation on the effects of the pressure ratio on the wall-impingement spray characteristics of nitrogen gas using a compressed natural gas (CNG) injector was conducted. The transient development of the impingement spray was recorded by a high speed camera with Z-type Schlieren visualization method. The spray behavior under various pressure ratio conditions were analyzed. The experimental results showed that the pressure ratio has positive effect on the development of spray wall-impingement. The effects of the above factor were evaluated in a constant volume chamber at atmospheric conditions. The data from test showed that, with the increase of the pressure ratio, the spray tip penetration (STP) quickly increases before the impingement and gradually increases after the impingement. Additionally, the spray velocity first increases and then sharply decreases on regardless of the injection pressure level. As the spray spreading angle increases, spray area and volume increases rapidly with the increase in STP at the beginning of injection, and finally entered a stable range, has a great correlation with the increase of pressure ratios.

• 한국분무공학회지
• /
• 제29권2호
• /
• pp.60-67
• /
• 2024

This study compared exhaust gas recirculation (EGR) and excess air strategies for improving thermal efficiency and emissions of hydrogen combustion engines at low-load operation. The experimental investigation was conducted in a single-cylinder, heavy-duty engine under throttling and wide-open throttle (WOT) conditions. Although both EGR and excess air strategies reduced peak heat release rates and increased combustion durations, the net indicated thermal efficiencies were improved by reducing the pumping losses. Under the constraint of similar nitrogen oxides emissions, the EGR strategy had higher net indicated thermal efficiencies compared to the excess air strategy in throttling operation. However, the difference between their thermal efficiencies was reduced under WOT condition. The trend of reducing nitrogen oxides emissions according to the two strategies was similar.

• 한국추진공학회지
• /
• 제16권5호
• /
• pp.1-9
• /
• 2012

동축형 다공성재 분사기에서는 중심 액체제트 주위를 둘러싼 원통형 다공성재의 내부 표면에서 반경방향으로 분사된 기체가 중심액체제트와 상호작용을 하게 된다. 표면분사된 기체제트는 반경방향에서 축방향으로 발달하며, 그 과정에서 액체분무의 중심부까지 운동량을 효과적으로 전달하여 미립화 및 혼합 성능을 향상시킨다. 본 연구에서는 기체분사 면적 및 기체분사 질량유량을 변화시켜 각각 운동량 비 및 웨버수의 크기를 조절하였으며, 이에 따른 물-공기 모사추진제 수류시험에서의 분무특성에 대한 고찰을 수행하고 동일 스케일의 전단 동축형 분사기와의 비교 분석이 이루어졌으며, 동축형 다공성재 분사기에서 반경방향으로의 기체분사가 2상유체의 미립화/혼합에 긍정적인 영향을 주는 것으로 판단된다.

• 한국분무공학회지
• /
• 제20권3호
• /
• pp.149-155
• /
• 2015

With increasing of GDP, the registration number of passenger cars has exceeded 20 million last year in Korea. Especially, the registration number of the diesel engine vehicles has been increasing. However, the WHO(World Health Organization) IARC (International Agency for Research on Cancer) has reported that diesel engine exhaust gas is an one of HAPs, which has carcinogenic for human, and they have designated it to Group 1. To solve this problem, exhaust gas from diesel engines has to be controlled. Thus, it has been controlling by European regulatory standard in Korea. On the other hand, in order to meet the enhanced emission regulations, all manufacturing company applied $NO_x$ control device to vehicles such as EGR (Exhaust Gas Recirculation), SCR (Selective Catalytic Reduction) and so on. However, these devices (EGR, SCR) were operated by difference reaction mechanism respectively, and the composition of exhaust gas would be differenced from that of them. In this study, it was conducted to evaluate variety characteristics on changing of exhaust gas composition by each $NO_x$ control device, and the heavy duty diesel trucks were chosen as experimental vehicles. From the result, it revealed that vehicles (with EGR) were discharged higher THC as 52.5% than that of others (with SCR). However, it did not followed that trend, in the case of CO; it was discharged as 57.2% lower than that of others (with SCR). In the future, these data would be used to apply to efficient $NO_x$ control device for meeting to EURO 6.

• 한국분말재료학회지
• /
• 제27권2호
• /
• pp.139-145
• /
• 2020

The powder manufacturing process using the gas atomizer process is easy for mass production, has a fine powder particle size, and has excellent mechanical properties compared to the existing casting process, so it can be applied to various industries such as automobiles, electronic devices, aviation, and 3D printers. In this study, a modified A4032-xSn (x = 0, 1, 3, 5, and 10 wt.%) alloy with low melting point properties is investigated. After maintaining an argon (Ar) gas atmosphere, the main crucible is tilted; containing molten metal at 1,000℃ by melting the master alloy at a high frequency, and Ar gas is sprayed at 10 bar gas pressure after the molten metal inflow to the tundish crucible, which is maintained at 800℃. The manufactured powder is measured using a particle size analyzer, and FESEM is used to observe the shape and surface of the alloy powder. DSC is performed to investigate the change in shape, according to the melting point and temperature change. The microstructure of added tin (Sn) was observed by heat treatment at 575℃ for 10 min. As the content of Sn increased, the volume fraction increased to 1.1, 3.1, 6.4, and 10.9%.

• 한국분무공학회지
• /
• 제13권4호
• /
• pp.212-219
• /
• 2008

To develop the twin-fluid atomizer having the excellent performance of painting, the spray characteristics of how a wide area can be painted efficiently by one time spraying were studied in this paper. Spray phenomena are affected by the many factors determining the spray field such as the spraying pressure of gas, the spraying pressure and viscosity of liquid paints, the opening duration of needle valve, the design dimension of nozzle, and so on. As the results of experiments, these factors affecting on spray characteristics were suggested as followings; 1) The optimum spraying pressure of gas was $0.015{\sim}0.02\;kPa$, and the appropriate spraying pressure of liquid paint was 0.01kPa, In these situations, the setting up pressures must be compensated as much as the losing amount of pressure because a decompression occurred when operating valves. 2) The duration of opening the needle valve must be sustained for $1{\sim}2$ seconds to inject gas after spraying the liquid paint. This operating of the needle valve was necessary to avoid the affect on the changing of liquid column length, and to prevent the droplet deposit at the initial time of spraying. 3) The spray tip penetration was gained form the experimental equation, and the effective spraying angle was $85^{\circ}{\pm}5^{\circ}$ just at he appropriate spraying pressure of gas. The distribution of the area sprayed had the variation in $350{\pm}50\;mm$ because of the spraying pressure of gas, the its distance from the spray tip, and the lift of the needle valve.

• 한국분말재료학회지
• /
• 제17권3호
• /
• pp.190-196
• /
• 2010

In this paper, rapid solidified Mg-4.3Zn-0.7Y (at.%) alloy powders were prepared using an inert gas atomizer, followed by a severe plastic deformation technique of high pressure torsion (HPT) for consolidation of the powders. The gas atomized powders were almost spherical in shape, and grain size was as fine as less than $5\;{\mu}m$ due to rapid solidification. Plastic deformation responses during HPT were simulated using the finite element method, which shows in good agreement with the analytical solutions of a strain expression in torsion. Varying the HPT processing temperature from ambient to 473 K, the behavior of powder consolidation, matrix microstructural evolution and mechanical properties of the compacts was investigated. The gas atomized powders were deformed plastically as well as fully densified, resulting in effective grain size refinements and enhanced microhardness values.

• 한국분무공학회지
• /
• 제23권4호
• /
• pp.227-233
• /
• 2018

An automobile is composed of a combination of a lot of parts, and it is difficult to maintain the same performance from a new car until it's scrapped. Greenhouse gases included in automobile emissions are typically carbon dioxide and methane. It is expected that this greenhouse gas will change depending on the aging (cumulative mileage) of the automobile However, the greenhouse gas characteristics by cumulative mileage lack of actual data due to time and economic difficulties. Therefore, in this paper, we selected automobile with high sales by displacement in korea and carbon dioxide and methane were measured by using method of the related law. The cumulative mileage is as follows; within 160 km (Statutory mileage by 2010), 6500 km (current statutory mileage), 15000 km (approximately 1-year average mileage of Non-business passenger vehicle). As a result of the test, the emission of carbon dioxide and methane was the smallest at 6,500 km, and increased in order of 15000 km, within 160 km. Also, it was confirmed that the $CO_2$ emission change of a large displacement automobile is more smaller at each mileage. Although the greenhouse gas tends to increase as the mileage of the vehicle, it is thought that additional confirmation is required of since 15,000 km as well, because it can occur deviations due to taming process or mechanical friction of the automobile.