• 한국자동차공학회논문집
• /
• 제16권6호
• /
• pp.141-147
• /
• 2008

Hot-dip galvannealed sheet (GA) with high strength of 590MPa grade in tensile strength, has developed for automotive applications. However, for a successful application, the microstructure and galvannealing behavior of galvannealed TRIP steel sheets must be strictly controlled. High silicon contents steel has problems with weld-ability, zinc coating and reduction of retained austenite volume fraction after galvannealing process. The main purpose of this study is to solve the problem as indicated above.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.389-392
• /
• 2005

In the modern days, a galvannealed sheet steel(GA) instead of a cold rolled steel sheet has been widely used as an alternative to extend the life of automotive body. Accordingly, the mechanical properties of GA for automobiles were taken Into account and studied by comparing with the temperature variation on annealing in this study. To clarify the effect of surface features in the mechanical properties of GA, the several tests such as nanoindentation and FE-analysis were executed. For this goal use is made of the method of neural networks. The developed neural networks apply also to obtain reliable mechanical properties of the thin films. Load-displacement curve was computed by the analysis procedure and compared with experimental results.

• 한국표면공학회지
• /
• 제32권2호
• /
• pp.134-143
• /
• 1999

The effects of silicon on galvannealing behavior of interstitial-free (IF) steels were studied. The growth rate of the Fe-Zn alloy layer was retarded as silicon in the steel added. Titanium in steel strongly favors Fe-Zn reaction, in particular outburst structures, whereas silicon inhibit them. Cross-sectional and planar views of galvannealed coatings were investigated to characterize alloy phase development. A possible mechanism to explain the retardation effect of silicon is discussed in terms of concentration on surface and inhibition layer.

• 한국정밀공학회지
• /
• 제23권4호
• /
• pp.109-115
• /
• 2006

This paper is designed to estimate friction and powdering characteristic of coating layer on galvannealed sheet steel with different annealing temperature, which is 465, 505, 515 and $540^{\circ}C$, Estimations of powdering and friction were done using a $60^{\circ}$ bending test and one side friction test, respectively. In order to obviously understand the effect of coatings on friction cross-section of coatings before and after friction test was also observed by SEM. The results show that powdering of coatings is increased with increasing of annealing temperature and that friction characteristic greatly depends on powdering which leads to increase of real contact area between tools and coatings.

• Corrosion Science and Technology
• /
• 제10권2호
• /
• pp.47-51
• /
• 2011

Main issues in the automotive industry are the reduction of vehicle body weight for energy savings and improvement of crashworthiness for passenger safety. In order to address both these issues, there has recently been increasing application of galvannealed advance high strength steel (GA AHSS) sheets for automobiles. However, GA AHSS sheets have some surface defects such as coating bare spots due to the addition of solid-solution strengthening elements, which result in the deterioration of the galvannealing reaction. In this study, the effects of galvannealed manufacturing conditions on surface and mechanical properties, resistance spot weldability on a laboratory scale, and GA 980 MPa steel sheets produced by commercial continuous galvannealing line (CGL) were investigated.

• Journal of Welding and Joining
• /
• 제5권3호
• /
• pp.11-18
• /
• 1987

Effects of electrode tips shapes of spot welding on the galvannealed steel have been studied, and the results obtained from this studies are as follows. 1) Expulsion had no effect on the shear strength of the specimen but been observed on the tensile strength of the specimen. 2) Effect of holding time after welding was neglegible when the spot welding supplies enough heat input. 3) Depending on the sopt welding tip shape it has different weldbility. It has better weldability in the order of pointed shape, truncated shape and dome shape. But the effect of coolind was just the opposite of the above order.

• 대한기계학회논문집A
• /
• 제33권6호
• /
• pp.560-567
• /
• 2009

This paper was designed to estimate the adhesion strength of galvannealed coatings on steel sheets. The adhesion strength were evaluated using single lap - shear tests where the lap joint was bonded by structural adhesive. Tests were performed for overlap length of 5mm, 10mm and 15 mm and three directions (0, 45, 90) of steel sheets used as the adherend of the overlap joint. After the tests, FE simulations of the single lap-shear test were also carried out to observe the stress distribution in the interface between the adhesive and the coated sheet. The results showed that the joint failure loads obtained from the tensile tests of bonded single lap-joints were the same, regardless of overlap lengths and directions of steel sheets. Also, the failure of galvannealed coatings greatly depended on shear stress distribution in the interface and the value was about 30MPa.

• 대한금속재료학회지
• /
• 제46권2호
• /
• pp.58-64
• /
• 2008

Surface-void defects observed on the galvannealed(GA) steel sheets in Interstitial-free high-strengthened steels containing Si and Mn have been investigated using the combination of the FIB(Focused Ion Beam) and FE-TEM(Field Emission-Transmission Electron Microscope) techniques. The scanning ion micrographs of cross-section microstructure of defects showed that these defects were identified as craters which were formed on the projecting part of the substrate surface. Also, those craters were formed on the Si or Mn-Si oxides film through the whole interface between galvannealed coating and steel substrate. Interface enrichments and oxidations of the active alloying elements such as Si and Mn during reduction annealing process for galvanizing were found to interrupt Zn and Fe interdiffusion during galvannealing process. During galvannealing, Zn and Fe interdiffusion is preferentially started on the clean substrate surface which have no oxide layer on. And then, during galvannealing, crater is developed with consumption of molten zinc on the oxide layer.

• 대한금속재료학회지
• /
• 제46권8호
• /
• pp.495-505
• /
• 2008

With the high proportion of zinc coated steels in body-in-white assembly, newly developed surface roughness textured galvannealed steel sheets have been introduced. In this study, zinc coated and surface roughness textured steel sheets were welded by resistance spot welding to investigate its weldability including electrode wear test. Based on the results of tensile-shear test, nugget diameter changes, and electrode tip growth test, it was clear that both surface roughness textured steels (GA-T and GA-E) showed good weldability. Also, there was no large difference in weldability and electrode wear behavior between GA-T and GA-E steels which have different surface roughness morphology. An analysis of electrode degradation showed Fe and Zn penetration through the electrode tip surface at 2400 welds reached $55{\sim}60{\mu}m$ and $75{\sim}80{\mu}m$, respectively. Therefore, there is no significant effect of surface roughness morphology on spot weldability of surface roughness textured galvannealed steel sheets. However, slight difference in thickness of alloying layers existing on electrode tip was found between GA-T and GA-E steels.

• 소성∙가공
• /
• 제14권8호통권80호
• /
• pp.696-703
• /
• 2005

In the modern days, a galvannealed sheet steel (GA) instead of a cold rolled steel sheet has been widely used as an alternative to extend the life of automotive body. Accordingly, the mechanical properties of GA for automobiles were taken into account and studied by examining their variation with annealing temperature. To clarify the effect of surface features on the mechanical and frictional properties of GA, the several tests such as nanoindentation, Vickers hardness and nano scratch test were executed. The frictional characteristics of coating layers of GA were examined through nano scratch test in this study. The friction coefficient of coating layers on the surface was obtained from the nano scratch. The variation of friction coefficient versus velocity and pressure was taken into consideration in this paper. Hardness and elastic modulus of coating layer were increased as increasing annealing temperature.