• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.13 no.1
• /
• pp.61-66
• /
• 2014

This paper describes the design, fabrication, and measurement of a compact hexa-band coupling antenna for 4G mobile handset using a small element with two slots. In order to obtain sufficient bandwidth (LTE700, GSM850, GSM900, GSM1800, GSM1900, UMTS) with a Voltage Standing Wave Ratio $(VSWR){\leq}3:1$, two slots are inserted in the small element, and coupling patch is used. The measured result of the fabricated antenna provides 410MHz bandwidth form 0.688 to 1.098GHz and 643 MHz bandwidth form 1.607 to 2.250GHz (${\leq}VSWR 3:1$) with the gain ranging from -0.52 to 4.68 dBi. Also, a good radiation pattern is achieved within the hexa-band (0.698-0.960GHz and 1.710-2.170GHz) range.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.3
• /
• pp.257-267
• /
• 2015

This paper presents a ultra-wideband sinuous antenna that operates in a whole frequency range (0.824~5.85 GHz) of Cellular/GSM-800, GSM900, ISM, GPS, DCS/GSM1800, PCS/GSM1900, WCDMA/UMTS/IMT2000, WiBro, WLAN and WiMax. The proposed antenna, which is composed of two sinuous arms, is designed as a self-complementary structure in order to have frequency-independent characteristics. It also uses a wideband balun of Klopfenstein taper structure to match to $50{\Omega}$. Experimental results show that the -10 dB return loss bandwidth of the proposed antenna is 5.24 GHz that ranges from 0.76 to 6 GHz, which covers all the frequency bands of the various wireless services. Within the entire operating frequency range, the measured radiation patterns in both E-plane and H-plane show nearly constant bidirectional broadside beams and the maximum antenna gain is measured to fall between 2.32~6.01 dBi.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.7
• /
• pp.737-743
• /
• 2011

In this paper, we designed and implemented a Monopole+IFA(Inverted F Antenna) hybrid antenna using the coupled feeding structure for the all band mobile phone. Studied antenna has wide band characteristics by the simultaneous operation both monopole and IFA under the coupled feeding structure. An antenna has designed PCB embedded type without antenna carrier component for the low in cost. Implemented antenna has within 2.5:1 for VSWR under LTE/CDMA/GSM900/DCS/USPCS/WCDMA/WiBro/WiFi in all band for the mobile services Measured average gains and efficiencies were -3.98~-0.09 dBi and 40.03~97.99 % for the LTE, CDMA, GSM900 band, and -3.90~-1.01 dBi and 40.70~79.31 % for the DCS, USPCS, WCDMA, WiBro, WiFi band. It's shown that studied antenna can be applied to all band mobile phone antenna including LTE.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.4
• /
• pp.357-364
• /
• 2015

In this paper, we designed and implemented a PIFA(Planar Inverted F Antenna) + IFA(Inverted F Antenna) hybrid MIMO(Multi Input Multi Output) antenna for the hexa mobile communication service band. By the simultaneous operation both PIFA and IFA using the coupled feeding structure, we tried for application to modern mobile phones that have large ground size. A PIFA is applied to the ground area, and an IFA is applied to no ground small space on top of the phone. A diagonal fed MIMO antenna is implemented PCB embedded type without antenna carrier component. Implemented antenna on the bare board measured within 3 : 1 for VSWR under hexa mobile communication band as CDMA, GSM900, DCS, KPCS, USPCS, and WCDMA. Measured average gains and efficiencies were -5.19~-3.16 dBi and 30.27~48.26 % for the CDMA, GSM900 band, and -9.50~-5.19 dBi and 11.23~30.28 % for the DCS, KPCS, USPCS, WCDMA band. It's shown that studied antenna can be applied to the antenna for the modern mobile phone.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.9
• /
• pp.19-27
• /
• 1998

The Transmitter part of single RF transceiver chip for an extended GSM handset application was circuit-designed, fabricated adn evaluated. The RF-IC Chip was processed by 0.8${\mu}m$ Si BiCMOS, 80 pin TQFP of $10 {\times} 10mm$ size, 3.3V operated RF-IC reveals, in general, quite reasonable integrity and RF performances. This paper describes development resuts of RF transmitter section, which includes IF/RF up-conversion mixer, IF/RF polyphase and pre-amplifier. The test results show that RF transmitter section is well operated within frequency range of 880~915MHz, which is defined on the extended GSM(E-GSM) specification. The transmitter section also reveals moderate power consumption of 71mA and total output power of 8.2dBm.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.9
• /
• pp.9-18
• /
• 1998

A single RF transceiver chip for an extended GSM handset application was designedm, fabricated and evaluated. A RFIC was fabricated by using silicon BiCMOS process, and then packaged in 80 pin TQFP of $10 {\times} 10 mm^{2}$ in size. As a result, it was achieved guite reasonable integraty and good RF performance at the operation voltage of 3.3V. This paper describes development results of RF receiver section of the RFIC, which includes LNA, down conversion mixer, AGC, switched capacitor filter and down sampling mixer. The test results show that RF receiver section is well operated within frequency range of 925 ~960 MHz, which is defined on the extended GSM specification (E-GSM). The receiver section also reveals moderate power consumption of 67 mA and minimum detectable signal of -105 dBm.

• Journal of Communications and Networks
• /
• v.1 no.3
• /
• pp.158-165
• /
• 1999

This paper studies interconnection of DCS1800 and GSM900 dual-band networks. Two types of interconnection config-urations for GSM services, non-overlap and overlap, are described. We propose analytic and simulation models to investigate the ben-efit of the overlap configuration. Our results explain how the radio channel capacities, the inter-system handoff failure rate, the origi-nating call traffic ratio and the offered loads affect the system per-formance. This study indicates that with appropriate overlap con-figuration, the GSM dual-band network can significantly improve the quality of cellular service.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.8A
• /
• pp.1169-1178
• /
• 1999

In this paper, the method to improve audio noise when GMS(Global System of Mobile Communication) is built in HPC(Handheld PC)is provided. The biggest problem with quality of audio is improved by connecting GSM module with wire to the widest erea near by HPC Power Ground to reduce impedance difference, and designing amplifier and earpiece, Result of measurement is satisfied with GSM Acoustic Standard. Standard of GSM Audio is declared in GSM 11.10 ETS 300 607-1. Measuring items corresponds to that standard and B&K Type 6712 is used for measurement. The list of measurement presented in this paper is Sending Sensitivity Frequency Response and SLR, Sending Loudness Rating( SLR level), Receiving Sensitivity Loudness Rating(RLR level), Talker Sidetone(STMR), Stability margin, and Echo Loss(ERL)

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.1
• /
• pp.40-46
• /
• 2002

In this paper we design and fabricate the Skeleton slot antenna which operates dually in GSM 900 and 1800 bands. Its simulation results are also compared with the measured ones. The original Skeleton slot antennas had the problems of unsatisfactory VSWR characteristics and considerably changing horizontal radiation patterns at high frequencies, but the proposed design improves these problems using multi-path feeding network and folding structure. The size of the radiator is 154 $\times$ 106(mm), and its height is 33(mm), and the reflector of 190$\times$190(mm) is used. The material of the radiator and reflector is 1mm-thick aluminum. Using NTC process reduces the mass production cost significantly. The measured return losses are 13.7 % at 900 MHz band and 16.4 % at 1800 MHz band, respectively. The horizontal radiation beam width is stable within $\pm$ 1$^{\circ}$ at both frequency bands.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.5
• /
• pp.185-189
• /
• 2005

This paper focuses on the design for Rx/Tx switch module of GSM(global standard mobile) band, characterization of a miniature, low power and dual-band implementation of the front-end switch module with low-pass filer And the effort to make agreement between the simulated design and the measured data for these solutions takes the place through accumulated design and manufacturing data library. We present the design, modeling and measurement of switch module integrating GSM Rx/Tx switching circuit and LPF(low pass filter) on a LTCC(low temperature co-fired ceramic) substrate. For GSM application, insertion and return loss of the low pass filter designed was less than 0.3 dB which was less than 12.7 dB at 900 MHz. The LTCC switch module contained 10 embedded passives and 3 surface mount components integrated on 4.6$\times$4.8$\times$1.2 mm, 6-layer multi-layer integrated circuit. The insertion loss of switch module measured at 900 MHz was 11 dB. In both of the design approach yielded excellent agreement between measured and simulated results.