• 한국정보통신설비학회:학술대회논문집
• /
• 2009.08a
• /
• pp.275-280
• /
• 2009

Femtocells are viewed as a promising option for mobile operators to improve coverage and provide high-data-rate services in a cost-effective manner Femtocells can be used to serve indoor users, resulting in a powerful solution for ubiquitous indoor and outdoor coverage. TThe frequency accuracy and phase alignment is necessary for ensuring the quality of service (QoS) forapplications such as voice, real-time video, wireless hand-off, and data over a converged access medium at the femtocell. But, the GPS has some problem to be used at the femtocell, because it is difficult to set-up, depends on the satellite condition, and very expensive. The IEEE 1588 specification provides a low-cost means for clock synchronisation over a broadband Internet connection. The Time of Packet (ToP) specified in IEEE 1588 is able to synchronize distributed clocks with an accuracy of less than one microsecond in packet networks. However, the timing synchronization over packet switched networks is a difficult task because packet networks introduce large and highly variable packet delays. This paper proposes an enhanced filter algorithm to reduce ths packet delay variation effects and maintain ToP slave clock synchronization performance. The results are presented to demonstrate in the intra-networks and show the improved performance case when the efficient ToP filter algorithm is applied.

• Journal of Navigation and Port Research
• /
• v.31 no.9
• /
• pp.763-769
• /
• 2007

A narrow loop noise bandwidth method is desirable to reduce the error of raw measurements due to the thermal noise. However, it degrades the performance of GPS initial synchronization such as mean acquisition time. And it restricts the loop noise bandwidth to a fixed value determined by the lower bound of the allowable range of carrier-to-noise power ratio, so that it is difficult to optimally track GPS signal. In order to make up for the weak points of the fixed-type narrow loop noise bandwidth method and simultaneously minimize the error of code and carrier measurements, this paper proposes a stepwise-type adaptive bandwidth algorithm for DGPS reference receivers. In this paper, it is shown that the proposed adaptive bandwidth algorithm can provide more accurate measurements than those of the fixed-type narrow loop noise bandwidth method, in view of analyzing the simulation results between two signal tracking algorithms. This paper also carries out sensitivity analysis of the proposed adaptive bandwidth algorithm due to the estimation uncertainty of carrier-to-noise power ratio. Finally the analysis results are verified by the experiment using GPS simulator.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.8
• /
• pp.1503-1510
• /
• 2007

To implement a high-precision lightning tracking system utilizing TDOA measurements, high-speed data acquisition and precise timing synchronization between ground sensors should be achieved. At the same time, considering the size of digitizer's memory, the data memory needs to be managed so that only the sampled data around the occurrence of stepped leader pulse is stored. This paper presents a detection-and-acquisition system for lightning signals that is the main equipment of ground sensor in lightning tracking system. GPS clock module is used to get precise timing synchronization and the 500MHz high speed digitizer is employed. In order to detect the leading edge of the lightning pulse and save the sampled data and its timing, lightning detection module is implemented and multi-record method is employed in the proposed system. Field experiment results show that the proposed system can detect and save the lightning signal efficiently.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.6
• /
• pp.910-915
• /
• 2018

The precise time, which is an essential element of the Global Navigation Satellite System (GNSS), such as US GPS, GLONASS in Russia, Galileo in Europe, and Beidou in China, is an important foundation for various economic activities around the world. Communication systems, power grids, IoT, Cloud computing and financial networks operate based on the precise time not only for the operating principles, but also for the synchronization and operational efficiency between tasks. In this paper, we introduce the Atomium software for the first time in South Korea. Atomium was developed by ORB in Belgium to calculate the clock error(clock solution) with GNSS signal observation data based on PPP method. The observation data is provided by Korea Research Institute of Standards and Science(KRISS). The results of MJD57106 with Atomium software are presented.

• Journal of IKEEE
• /
• v.26 no.2
• /
• pp.141-149
• /
• 2022

With the development of artificial intelligence and unmanned technologies, the remote surveillance/autonomous driving systems have been actively researched. For an effective performance analysis of the developed remote control system, it is important to record the data of it in real time. In addition, in order to analyze the performance between the control system and the remote system, the recorded data from them should be synchronized with time. In this paper we proposed a novel time synchronization method for the remote control system. The proposed remote control system satisfies the time difference of the recorded data within 1 ms, and we can reduce the time difference by using a CPU shielding and affinity setting. The performance of the proposed method was proved through various network data storage experiments. And the experiments confirmed that the proposed method can be applied to recording devices of unmanned ground vehicles and control vehicles. The proposed method will be used as a method for analyzing network data of UGV-R (Unmanned Ground Vehicle - Reconnaissance).

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.12B
• /
• pp.1037-1041
• /
• 2004

In this paper we propose a new conceptual slave clock system in which remotely located clock is synchronized to the reference clock by intermediation of the satellite time, show a probability of adoption to real network by experiments. This new proposed method has lots of structural advantages over the existing methods because all of the node clocks can be maintained with the same hierarchical quality. The measurement results show that the accuracy of the experimental slave clock system can be kept within a few parts in 1012 and that the MTIE (Maximum Time Interval Error) meets the ITU-T Recommendation G.811 for the primary reference clock A prototype system having fully automatic operational functions has been realized, and it is expected to be commercially used as a node clock for synchronization in the digital communication network in the near future.

• Journal of Satellite, Information and Communications
• /
• v.7 no.3
• /
• pp.99-104
• /
• 2012

The United States will proceed with the effort to modernize the GPS system, and one of its main content is to provide L5 signal. L5 will be transmitted in a radio band reserved exclusively for aviation safety services. And, L5, in combination with L1, will improve the position accuracy via ionospheric correction and robustness via signal redundancy. However, The acquisition processing time of L5 takes longer than that of L1 as the code length of L5 is 10 times longer than that of L1. To reduce this acquisition processing time, a higher number of correlators in the aquisition module should be used. However, there is a problem that this causes increase in the complexity of the correlator configuration and the computation power. So, in this paper, we propose L5 signal tracking scheme using tracking results in the GPS L1/L5 receiver. The proposed scheme could reduce the hardware complexity as the GPS L5 signal acquisition module is not needed, and provide fast and stable tracking of L5 signal by aiding L1 tracking results such as PRN, the code phase synchronization, and the Doppler frequency. The feasibility of the proposed scheme is demonstrated through simulation results.

• Journal of Internet Computing and Services
• /
• v.8 no.2
• /
• pp.1-13
• /
• 2007

GPS/GIS and RFID technologies have been changing the paradigm af our society toward ubiquitous era. Especially, geographically distributed mobile agents with transporting objects need to be automatically recognizable and traceable under certain conditions. To do this, fundamental theories and technologies are required to specify and verify spatial and temporal behaviors of agents on geographical space. This paper presents a new formal method, called Calculus of Real-Time Distribution, Mobility, and Interaction (CaRDMI), for this purpose. For specification, CaRDMI defines a map, mobile agents with transporting objects. The movement of on agent is represented by a path on the map, consisting of a list of nodes and a list of edges with spatial and temporal constraints. Interactive constraints among agents are represented by synchronization modes on objects at nodes. These constraints are distinguishable features of CaRDMI from other methods. Especially, many-to-many timed synchronization constraints are noticeable. For verification, CaRDMI presents the spatial, temporal and interactive deduction rules and the spatial and temporal equivalence relations.

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.1
• /
• pp.61-67
• /
• 2011

The GPS new civil signal is modulated on the L2 carrier at a frequency of 1227.6MHz. The L2C signal is composed of two multiplexed code signals, which include CM code with a 10,230 chip sequency repeating every 20ms, and CL code which has a 767,250 chip sequency repeating every 1.5 seconds. Thus, the new civil signal have much improved cross correlation properties so that the position fixing can be possible even with very weak signals. However, it requires very long acquisition time because of its long code length. This paper presents an efficient signal acquisition method for L2C AGPS receiver. Snapshot mode and coarse time assistance are assumed and total integration time is given by 1.5 sec. By SNR worksheet and computer simulation, it is proven that L2C signal can be acquired with very weak power less than -150dBm. Considering the acquisition time and the sensitivity, it is recommended that the highest power signal is acquired with CM code first to reduce TTFF. By the timing synchronization, at this time, search space of the code phase for other signals can be greatly reduced so that CL code can be used in signal acquisition to maximize sensitivity with small computation.

• Korean Journal of Remote Sensing
• /
• v.19 no.1
• /
• pp.91-97
• /
• 2003

The design of Graphic Information System(GIS) in various applications is suffering from the difficulty of data acquisition, which is labor-intensive and time consuming. In order to provide the spatial data rapidly and accurately, 4S-Van, a prototype mobile mapping system, has been developed. The 4S-Van consists of 1)Global Positioning System(GPS), Inertial Navigation System(INS) for estimating the geographic position and attitude of the moving van, i.e.,(x, y, z) and the direction of the Van, 2) Charge Coupled Device(CCD) camera and laser scanner for capturing images and for measuring depth from geographic objects, and 3) External Synchronization Device(ESD) and industrial PC for synchronizing data from GPS/INS/CCD camera and for storing the data. In this paper, we present the design and implementation of the proto-Dpe 4S-Van system for spatial data acquisition for various GIS applications.