• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.6C
• /
• pp.502-511
• /
• 2012

As the importance of GNSS system increases, the necessity of independent system is increased also. When the independent GNSS system is required, GNSS signal design is necessary with requirement definition. This paper suggests the design method of GNSS signal using the analysis result of receiver performance. First, the candidates are defined based on the design elements. Then the receiver performance of the candidates is analyzed based on the performance evaluation parameters. The weights of performance evaluation parameter are defined in order to consider the receiver performance in a various aspects. Finally, the calculation of normalized performance evaluation parameters and weights are derived to obtain the compared value for signal selection. Spreading code, modulation method and carrier frequency are considered as design parameters. Also, correlation width, DLL PLL thermal noise jitter, frequency bandwidth and side lobe peak ratio are considered as performance evaluation parameters. And positioning performance, robustness to noise, bandwidth efficiency are considered as the performance aspects. This paper analyzes the performance of each candidate using software based simulator and suggest the method to compare objectively the performance of each candidates.

• Journal of Advanced Navigation Technology
• /
• v.18 no.4
• /
• pp.288-295
• /
• 2014

Current ILS is difficult for the many aircraft to access to the system at the same time because of it's system. And the equipments should be installed at the direction of every runway. Also, There is limitation that landing procedures must be have of only ILS single course when the aircraft land on the ground. hereupon, The more air traffic exist, the longer delay time of flight be. GBAS using the GNSS has been developed to overcome those limitations. Before flight test in Teean airport, this paper compares the taean approach procedure and curved approach procedure by using the simulator. Comparison study shows that curved approach procedure takes less flight time, low fuel consumpsion and make it possible to avoid noise airspace more than original procedure.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.2
• /
• pp.353-357
• /
• 2006

One-sided and two-sided ATF for GNSS receiver are deigned, implemented and evaluated in this paper. The difference f filter characteristics such as the location of zeros and the frequency response is reviewed and examined with experiments. NLMS adaptation algorithm is adopted for updating the weighting coefficients of the 12-tap FIR filter. he performance of ATF is evaluated using real signals consisting of the signals from GPS simulator and the signal generator. The output of ATF is fed into the SDR to evaluate SNR and the position accuracy. The complexity of implementation is also compared and the effects of the time delay and the phase delay are examined. The experimental results show that one-sided and two-sided ATF give similar performance against single tone CWI.

• Journal of Navigation and Port Research
• /
• v.38 no.4
• /
• pp.373-378
• /
• 2014

In order to prepare for recapitalization of differential GNSS (DGNSS) reference station and integrity monitor (RSIM) due to GNSS diversification, this paper focuses on differential correction algorithm using GPS/Galileo pesudorange. The technical standards on operation and broadcast of DGNSS RSIM are described as operation of differential GPS (DGPS) RSIM for conversion of DGNSS RSIM. Usually, in order to get the differential corrections of GNSS pesudorange, the system must know the real positions of satellites and user. Therefore, for calculating the position of Galileo satellites correctly, using the equation for calculating the SV position in Galileo ICD (Interface Control Document), it estimates the SV position based on Ephemeris data obtained from user receiver, and calculates the clock offset of satellite and user receiver, system time offset between GPS and Galileo, then determines the pseudorange corrections of GPS/Galileo. Based on a platform for performance verification connected with GPS/Galileo integrated signal simulator, it compared the PRC (pseudorange correction) errors of GPS and Galileo, analyzed the position errors of DGPS, DGalileo, and DGPS/DGalileo respectively. The proposed method was evaluated according to PRC errors and position accuracy at the simulation platform. When using the DGPS/DGalileo corrections, this paper could confirm that the results met the performance requirements of the RTCM.

• Journal of Astronomy and Space Sciences
• /
• v.27 no.2
• /
• pp.117-122
• /
• 2010

An ionospheric error simulation is needed for creating precise Global Positioning System (GPS) signal using GPS simulator. In this paper we developed Klobuchar coefficients n ${\alpha}_n$ and ${\beta}_n$ (n = 1, 2, 3, 4) generation algorithms for simulator and verified accuracy of the algorithm. The algorithm extract those Klobuchar coefficients from broadcast (BRDC) messages provided by International GNSS Service during three years from 2006 through 2008 and curve-fit them with sinusoidal and linear functions or constant. The generated coefficients from our developed algorithms are referred to as MODL coefficients, while those coefficients from BRDC messages are named as BRDC coefficients. The maximum correlation coefficient between MODL and BRDC coefficients was found for ${\alpha}_2$ and the value was 0.94. On the other hand, the minimum correlation was 0.64 for the case of ${\alpha}_1$. We estimated vertical total electron content using the Klobuchar model with MODL coefficients, and compared the result with those from the BRDC model and global ionosphere maps. As a result, the maximum RMS was 3.92 and 7.90 TECU, respectively.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.9
• /
• pp.781-788
• /
• 2016

In this paper, a real-time on-board orbit determination algorithm using the high precise orbit propagator is suggested and its performance is analyzed. Orbit determination algorithm is designed with the Extended Kalman Filter. And it utilizes the orbit calculated from the Pseudo-range as observed data. The performance of the on-board orbit determination method implemented in the GPS-12 receiver is demonstrated using the GNSS simulator. Orbit determination performance using high precise orbit propagator was analyzed in comparison to the orbit determination result using $J_2$ orbit propagator. The analysis result showed that position and velocity error are improved from 43.61 m($3{\sigma}$) to 23.86 m($3{\sigma}$) and from 0.159 m/s($3{\sigma}$) to 0.044 m/s($3{\sigma}$) respectively.

• Smart Structures and Systems
• /
• v.17 no.5
• /
• pp.743-751
• /
• 2016

An ongoing research project is devoted to the design and implementation of a satellite based asset tracking for supporting emergency management in crisis operations. Due to the emergency environment, one has to rely on a low power consumption wireless communication. Therefore, the communication hardware and software must be designed to match requirements, which can only be foreseen at the level of more or less likely scenarios. The latter aspect suggests a deep use of a simulator (instead of a real network of sensors) to cover extreme situations. The former power consumption remark suggests the use of a minimal computer (Raspberry Pi) as data collector.

• Journal of Positioning, Navigation, and Timing
• /
• v.3 no.2
• /
• pp.63-69
• /
• 2014

In this study, due to the necessity of the equipment for inspecting an anti-jamming function depending on the expansion of the development of anti-jamming systems, an array antenna hood that can inspect the anti-jamming function of an anti-jamming system while being installed at the system was designed and manufactured. The manufactured array antenna hood plays a role in radiating GNSS signals and jamming signals. Based on an experiment, it was demonstrated that using a near-field radiation method, the manufactured array antenna hood could be used for examining the normal operation of an anti-jamming system function in outdoor or indoor environments rather than an anechoic chamber.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.7 no.2 s.17
• /
• pp.48-56
• /
• 2004

This paper presents the GPS receiver's inherent interference effectiveness based on the receiver's internal processing gain. This research is to verify the weakness of the GPS satellite signals and evaluate the receiver's vulnerability in an interference situation. The experiment for the narrow band interference effectiveness for the L1 C/A code GPS receiver has been performed by using the Spirent GSS4765 jamming simulator. After analyzing the experimental result, it is compared with the calculated J/S value of the two different L1 C/A code GPS receivers. By the above result, the narrowband jamming effectiveness of the each jamming source and the jamming margin for the each receiver are to be analyzed in detail. Finally, we could utilize the result to analyze the jamming effectiveness on the GNSS receiver.

• Journal of Navigation and Port Research
• /
• v.33 no.6
• /
• pp.395-400
• /
• 2009

In order to prepare for the DGNSS recapitalization and implementation of the functions for software based reference station and integrity monitor (RSIM) system, this paper proposes a design of integrity monitor functions of maritime differential GPS RSIM. The most critical functions of the integrity monitor (IM) are to generate and send flags to the reference station (RS) along with system feedback. Firstly, it presents the architecture of software based RSIM, and analyzes the performance standard of integrity monitor for maritime DGPS reference station This paper then designs the functions of integrity monitor for DGPS reference station based on the performance standard. Finally, this paper presents the results of performance analysis for the functionality of integrity monitor using the GNSS simulator. it discusses the study method and its application for the system implementation.