• Journal of the Korea institute for structural maintenance and inspection
• /
• v.20 no.6
• /
• pp.30-39
• /
• 2016

An experimental study was performed to investigate flexural performance and bond characteristics of RC beams strengthened using ductile polyethylene terephthalate(PET) with low elastic modulus. Bond tests were planned and completed following CSA S806. Test variables were fiber type and fiber amount. Also, total of 8 RC beams was tested. Major test variables of the beam tests included section ductility(${\mu}=3.4$, 7.0), fiber type(CF, GF, PET) and amount of fiber strengthening. Moment-curvature analyses of the beam sections were also performed. In bond tests, the bond stress distribution as well as the maximum bond stress increased with increasing amount of PET. In case of 10 layers of PET, the effective bond length was 60 mm with the maximum and the average bond stress of 2.33 and 2.10 MPa, respectively. RC beam test results revealed that the moment capacity of the RC beams strengthened using PET 10 and 20 layers increased over the control beam with little reduction in ductility by fiber strengthening. All beams strengthened using PET resulted in ductile flexural failure without any sign of fiber debonding or fiber rupture. It was important to include the mechanical properties of adhesive in the moment-curvature analysis of PET-strengthened beam sections.

• Journal of the Korean Ceramic Society
• /
• v.36 no.2
• /
• pp.107-115
• /
• 1999

Microstructural variation and strengthening effects with lamination methods of alumina fiber-reinforced ${\gamma}$-LiAlO2 matrixes for Molten Carbonate Fuel Cell(MCFC) were studied. The porosities of all matrix laminated by hot-pressing of two green sheets under 1 kg/$\textrm{cm}^2$ at 45$^{\circ}C$ for 1 min and by double-casting which the second layer cast on the first green sheet dried for 3.5h were more than 50%. The strength of the Al2O3 fiber-reinforced matrix prepared by lamination was enhanced by 70% in comparison with the non-laminated matrix (115 gf/$\textrm{mm}^2$) and the strength-directionality due to fiber-orientation also could be removed. The strength of matrixes laminated by triple-casting was higher than that of the double-cast matrix, but triple-cast matrix showed the directionality with the casting direction, and furthermore its porosity was less than 50%. Although the strength of matrixes laminated by double-casting (195 gf/$\textrm{mm}^2$) is slightly less than that of matrixes laminated by hot-pressing (212 gf/$\textrm{mm}^2$), the double-casting method was evaluated to be more efficient laminating process in MCFC matrix processing.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.31B no.3
• /
• pp.60-68
• /
• 1994

In this paper, the multiplicative algorithm of two polynomials over finite field GF(($p^{m}$) is presented. Using the presented algorithm, the multiple-valued multiplier of the serial input-output modular structure by CCD is constructed. This multiple-valued multiplier on CCD is consisted of three operation units: the multiplicative operation unit, the modular operation unit, and the primitive irreducible polynomial operation unit. The multiplicative operation unit and the primitive irreducible operation unit are composed of the overflow gate, the inhibit gate and mod(p) adder on CCD. The modular operation unit is constructed by two mod(p) adders which are composed of the addition gate, overflow gate and the inhibit gate on CCD. The multiple-valued multiplier on CCD presented here, is simple and regular for wire routing and possesses the property of modularity. Also. it is expansible for the multiplication of two elements on finite field increasing the degree mand suitable for VLSI implementation.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.1
• /
• pp.880-883
• /
• 2005

This paper presents a method of constructing the sequential logic machines over finite fields(or galois fields). The proposed the sequential logic machines is constructed by as following. First of all, we obtain the linear characteristics between present state and next state based on mathematical properties of finite fields and sequential logic machines. Next, we realize the sequential logic machines over finite field GF(P) using above linear characteristics and characteristic polynomial that expressed using by matrix.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.41 no.1
• /
• pp.17-26
• /
• 2005

There are several problems in the commercial pound net in the heavy tide ; the breaking and loss of net, steeply variation of net shape and decreasing of fishing efficiency, etc. In order to solve these problems, we introduced method of added sinker used to coastal cultivating cage of Japan and investigated the possibility of application to the Korean pound net. The results are obtained as follows; 1. In case of the upperward flow with fish court net, tension of the frame line was increased about 10${\sim}$25% than that of prototype according to the added sinker from 1.3gf to 5.2gf. The tension of A-type and B-type was similar to the case of the prototype, the tension of C-type and D-type was increased about 10${\sim}$15% than that of prototype. 2. The variation of deformed angle of fish court net was from 0$^{\circ}$ to 70$^{\circ}$ and that of the slope net was from 0$^{\circ}$ to 64$^{\circ}$ and that of the second bag net was from 0$^{\circ}$ to 46$^{\circ}$ and the depth of the second bag net was increased about 10% when the added sinker was changed from 1.3gf to 5.2gf. The depth of the first bag net and the second bag net were decreased about 50% than that of initial depth. 3. For the deformed angle of fish court net according to the attached point of the added sinker, A-type and B-type were decreased about 25% and 10% than the prototype, respectively. C-type was similar to the case of the prototype and D-type was increased about 15% than that of the prototype. The depth of slope net became deep in turn of A-type, B-type, C-type and D-type. For the depth of the second bag net, A-type, B-type, C-type and D-type were increased about 10${\sim}$15% than that of prototype. The depth of the slope net was changed from 0$^{\circ}$ to 63$^{\circ}$ and that of the second bag net was changed from 0${\sim}$44$^{\circ}$ according to the increase of velocity. 4. The optimal weight of added sinker was about 2.6${\sim}$3.6gf and the optimal attached point of added sinker was the case of C-type and D-type.

• Journal of the Korean Society for Precision Engineering
• /
• v.3 no.1
• /
• pp.69-76
• /
• 1986

The measuring Method by stylus, which measures surface roughness, has been widely used since G. Schmaltz developed the first equipment of that type. Withe the resent development of the measuring method by stylus, surface foughness testing instruments of the very high magnification ratio, hundreds of thousands, are manu- factured. However, as the techniques of the high precision roughness measurement are being required, the response problems due to the tip shapes and the plastic deformations of measured surface of mild material are to be serious factors. In this study, diamond stylus of tip radius $0.5\mu\textrm{m}$, $2\mu\textrm{m}$, $5\mu\textrm{m}$ and $10\mu\textrm{m}$ were used under the measuring force of 0.01gf, 0.02gf, 0.07gf, 0.4gf and 1.6gf, and from the experimental data, maximum measured value devrements between $2\mu\textrm{mR}$ stylus and $5\mu\textrm{mR}$ stylus, $2\mu\textrm{mR}$ stylus and $10\mu\textrm{mR}$ stylus are 22% and 31%, respectively when the measured value of $2\mu\textrm{mR}$ stylus goes to $0.01\mu\textrm{m Ra}$, $\lambda$ c2.5mm. And it is shown that plastic deformations on the plastic deformations on the measured surface are proportional to W/R(W;measured force, R;stylus tip radius).

• The Research Journal of the Costume Culture
• /
• v.13 no.1
• /
• pp.47-59
• /
• 2005

This study aims to measure stretch rate of standard weight in the $2{\times}1$ rib stitch and $2{\times}2$ rib stitch, and to apply features of rib stitch to the knit pattern. The reviewer examined the sample knit for test with 100% wool, $2/48's{\times}2$, 12 gauge, and then made knit patterns and sample clothes for test considering stretch rate of standard weight of 10gf, 15gf, 20gf, 25gf based on the results from the former test, and finally estimated the try-outs for sample clothes. This study came out with the following results: From the functional estimate of knit patterns made by standard stretch rate of each stitch, the 20gf weight sample clothes of $2{\times}1$ and $2{\times}2$ rib stitchs were in high estimate. For the bust, B/4~ -4.6cm knit pattern was made of $2{\times}1$ rib stitch, B/4~5.3cm of $2{\times}2$ rib stitch. In conclusion, because $2{\times}1$ and $2{\times}2$ rib stitchs has the much higher stretch rate in the direction of the course than $0{\times}0$ ad $1{\times}1$ rib stitchs, high stretch rate of standard weight should be applied to the case of making knit wear. It is expected that this will lead stable sizing and measurement system when used in making knit patterns, and satisfy knit wearers' various needs.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.3
• /
• pp.633-637
• /
• 2005

In this contribution, we developed and improved an existing GF (Galois field) dividing algorithm by suggesting a novel architecture for a finite field divider, which is frequently required for the error correction applications and the security-related applications such as the Reed-Solomon code, elliptic curve encryption/ decryption, is proposed. We utilized the VHDL language to verify the design methodology, and implemented the architecture on an FPGA chip. We suggested the n-bit lookup table method to obtain the throughput of 2m/n cycles, where m is the order of the division polynomial and n is the number of the most significant lookup-bits. By doing this, we extracted the advantages in achieving both high-throughput and less cost of the gate areaon the chip. A pilot FPGA chip was implemented with the case of m=4, n=2. We successfully utilized the Altera's EP20K30ETC144-1 to exhibit the maximum operating clock frequency of 77 MHz.

• Fashion & Textile Research Journal
• /
• v.2 no.5
• /
• pp.430-436
• /
• 2000

The purpose of the study was to obtain the basic data on the self-adjusting ability of the support panty stockings. Ten healthy women in the twenties were selected as subjects and clothing pressure of 9 support panty stockings made of single covered yarn (SCY) and double covered yarn (DCY) were measured under the standard environmental condition for the study. Data was analysed statistically according to body postures, sides, and parks. The results were as follows: Clothing pressure according to body posture was order of 'sitting-on-a-chair', 'stepping-up-a-stair', and 'standing'. High clothing pressure was obtained in the parts of calf ($9.4gf/cm^2$) in 'standing' and knee (9.7 and $16.5gf/cm^2$) in both 'stepping-up-a-stair' and 'sitting-on-a-chair', respectively. The order of clothing pressure with body sides was 'front', 'side', and 'back'. The highest clothing pressure was knee ($18.8gf/cm^2$) on the front, thigh ($8.8gf/cm^2$) on the side, and calf ($6.4gf/cm^2$) on the back. Clothing pressure of DCY at abdomen and knee was a little higher than those of SCY 3. In terms of material structure variation, clothing pressure of thigh, calf and ankle with SCY was a little higher than those with DCY, while clothing pressure of abdomen and knee with DCY was a little higher than those with SCY.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.20 no.6
• /
• pp.975-982
• /
• 1996

This study was conducted to examine the fatigue phenomenon of mechanical properites in denim fabrics for slacks during repeated shear and tensile deformation by analysing the change in the basic dynamic properties of fabrics on the basic of experiments to obtain the basic data necessary to measure their fatigue. In addition, this study was carried out by allowing these denim fabrics at market to go through the repeated deformation under such different loads as 500 gf/cm2 and 1000 gf/cm2 by using a simulated fatigue tester, by calculating both dynamic properties and hand value (HV) of these fabrics with KES-F system and then by obtaining the THV through these calculated properties. The results are as follows: 1 The fatigue phenomenon of dynamic properties was remarkably shown by the repeated shear and tensile deformation, while the increase of hysterical plastic substances was also remarkable in these shearing and bending properties. 2. The elasticity values of tensile, bending and compression properties, such as, B and G were reduced: whereas RT and RC values increased. It was shown, then, that those fabrics lost their elasticity and became flexible and soft with the increase of fatigue. 3. The fatigue phenomenon of hand value also showed that those fabrics became soft in relation with the change of all dynamic properties, and that their performance was also change to flexible hand value. 4. TRhe degree of fatigue was also shown by the loads given to the repeated deformation. It was shown that the fatigue was higher for the tensile load of 1000 gf/cm3 than did the standard load of 500 gf/cm3 It is necessary, therefore, to consider the load in accordance with their usage when examining the fatigue phenomenon with respect to the dynamic properties of clothing materials. 5. The loads were nearly not influenced by the change in the general hand value tended to show a little of increase with the increase of fatigue, Based on those results, it seems that the fatigue phenomonon is related to the loads given to the repeated deformation.