• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.457-458
• /
• 2008

This paper presents an output common mode current compensation method to achieve both constant Gm and constant gain. A conventional rail-to-rail CMOS op-amp with constant Gm was designed by using complementary differential input stage and current compensation skills. But it doesn't operate constant gain, because of output resistance variation. With $0.18{\mu}m$ CMOS process, the simulation results show that the differential gain variation can achieve less than 1.3dB. And a 60dB gain, a 13.5MHz unity gain-frequency, and 1mW power consumption, when operating at 1.8V and 10pF load.

• Journal of electromagnetic engineering and science
• /
• v.13 no.3
• /
• pp.165-172
• /
• 2013

This paper describes a design for a spiral antenna with a conical wall to obtain the high gain. The gain and the axial ratio of the spiral antenna were improved by a new design that included a conical wall and an optimized Archimedean slit on the ground plane in a conventional antenna with a circular cavity wall and a 4.5-turn slit. A gain improvement of 9.5 dBi higher and a good axial ratio of 1.9 dB lower were measured by the added conical wall and the newly designed slit from the current distribution control on the ground plane, respectively. The measured return loss, gain and axial ratio of the proposed antenna showed a good agreement with the simulated results. The proposed antenna will be applied to a non-linear junction detector system.

• Journal of Institute of Control, Robotics and Systems
• /
• v.9 no.9
• /
• pp.664-668
• /
• 2003

A new sliding mode control method based on the lower bound of control gain is presented. Although the magnitube of the proposed control input is larger than that of the conventional control input using both lower and upper bounds, the positive-negative exchanging chattering is reduced and reaching mode is shorter. Because the proposed scheme needs only the lower bound of control gain, it is applicable to the system whose upper bound of control gain is doubtful to determine such as the control gain depends on the system states. It is proved that the proposed control method guarantees the sliding condition. The analysis of differences between the conventional method and the proposed method is given. The validity of the proposed control strategy is shown through a 2nd-order nonlinear system example.

• Journal of Institute of Control, Robotics and Systems
• /
• v.13 no.9
• /
• pp.856-860
• /
• 2007

This paper presents a robust tracking controller design method for the track-following system of an optical recording device. A tracking loop gain adjustment algorithm is introduced to accurately estimate the tracking vibration quantity in spite of the uncertainties of the tracking actuator. A minimum tracking open-loop gain is calculated by the estimated tracking vibration quantity and a tolerable limit of tracking error. A robust tracking controller is designed by considering a robust $H_\infty$ control problem with the weighting function of a slightly larger gain than the minimum tracking open-loop gain. The proposed controller design method is applied to the track-following system of an optical recording device and is evaluated through the experimental result.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.37 no.5
• /
• pp.17-27
• /
• 2000

In a SCH(separate confinement heterostructure) QW(quantum well) laser, we calculated the optical gain, the differential gain and recombination current in the QW and derived the bulk carrier density in the SCH region as a function of the QW current by using the analytical capture escape model. Based upon above relations, we found the optical gain and the differential gain correspond to the ratios of carrier and current injected into the QW.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.11
• /
• pp.1207-1213
• /
• 2012

Typically commercial controllers do not give data of the controller gains. Therefore, it is very hard to determine the optimal controller gain even though the dynamic model is derived. In this case, design of experiment (DOE) methodology can be a powerful tool for gain tuning. In this research, gain tuning process is proposed based on the DOE. Micro parallel mechanism platform with 3 degrees-of-freedom (DOF) is used for the experiments. Controller gains are measured indirectly from the voltages of adjustable resistors. The controller gains of three actuators are optimized by two or three steps, respectively. The correlations of the controller gains are also analyzed. The process and methodology can be adopted in gain tuning of other mechanical systems.

• Journal of the Korean Regional Science Association
• /
• v.10 no.1
• /
• pp.53-70
• /
• 1994

The relationships between the Capital gains of housings by tenure, type and size have been analyzed. Major findings are (i) capital gain rate of 'chonsei' housing is larger than that of the owner occupied housing (ii) the small 'chosei' apartment has the highest capital gain rate and the lowest instability index (iii) the smaller the size of housings, the higher the capital gain rate and the smaller the instability index. Even though there is the 'structural change' in the capital gain rates of owner occupied and 'chonsei' housings, they are cointegrated. The capital gain of owner occupied housing is mainly affected by the real estate policies. But, The capital gain of 'chonsei' housing is mainly affected by the business cycle and the aggregate demand management policies.

• Journal of the Optical Society of Korea
• /
• v.10 no.4
• /
• pp.174-177
• /
• 2006

We propose a new technique to minimize gain-transient time of wavelength-division-multiplexing (WDM) signals in erbium-doped fiber amplifiers (EDFA) in channel add/drop networks. We have dramatically reduced the gain-transient time to less than $3{\mu}sec$ by applying, for the first time to our knowledge, a disturbance observer with a proportional/integral/differential (PID) controller to the control of EDFA gain. The $3{\mu}sec$ gain-transient time is the fastest one ever reported and it is approximately less than 1.5% of $200{\mu}sec$ gain-transient time of commercially available EDFAs for WDM networks. We have demonstrated the superiority of the new technique by performing the simulation with a numerical modeling software package such as the $Optsim^{TM}$.

• Korean Journal of Optics and Photonics
• /
• v.9 no.6
• /
• pp.413-416
• /
• 1998

We have flattened the gain of EDFA by using a long-period FBG filter and AOTF's. The gain and optical SNR characteristics of the gain-flattened EDFA in long-haul transmission been evaluated in a recirculating EDFA loop. The gain variation was less than 4.6 dB and the optical SNR was higher than 14 dB over 20-nm wavelength range when the optical signal went through the EDFA as many as 200 times. These results indicate that this gain-flattened EDFA is applicable for ultra long-haul WDM optical transmissions over 8000 km.

• Journal of the Optical Society of Korea
• /
• v.18 no.5
• /
• pp.442-448
• /
• 2014

For the first time, a novel analytical model of the net gain for a Raman-EDFA hybrid optical amplifier (HOA) is proposed and its various parameters optimized using a genetic algorithm. Our method has been shown to be robust in the simultaneous analysis of multiple parameters (Raman length, EDFA length, and pump powers) to obtain large gain. The optimized HOA is further investigated at the system level for the scenario of a 50-channel DWDM system with 0.2-nm channel spacing. With an optimized HOA, a flat gain of >17 dB is obtained over the effective ITU-T wavelength grid with a variation of less than 1.5 dB, without using any gain-flattening technique. The obtained noise figure is also the lowest value ever reported for a Raman-EDFA HOA at reduced channel spacing.