• 제목/요약/키워드: Fusion rate

검색결과 804건 처리시간 0.022초

Analysis and Optimization of Cooperative Spectrum Sensing with Noisy Decision Transmission

  • Liu, Quan;Gao, Jun;Guo, Yunwei;Liu, Siyang
    • KSII Transactions on Internet and Information Systems (TIIS)
    • /
    • 제5권4호
    • /
    • pp.649-664
    • /
    • 2011
  • Cooperative spectrum sensing (CSS) with decision fusion is considered as a key technology for tackling the challenges caused by fading/shadowing effects and noise uncertainty in spectrum sensing in cognitive radio. However, most existing solutions assume an error-free decision transmission, which is obviously not the case in realistic scenarios. This paper extends the general decision-fusion-based CSS scheme by considering the fading/shadowing effects and noise corruption in the common control channels. With this more practical model, the fusion centre first estimates the local decisions using a binary minimum error probability detector, and then combines them to get the final result. Theoretical analysis and simulation of this CSS scheme are performed over typical channels, which suggest some performance deterioration compared with the pure case that assumes an error-free decision transmission. Furthermore, the fusion strategy optimization in the proposed cooperation model is also investigated using the Bayesian criteria. The numerical results show that the total error rate of noisy CSS is higher than that of the pure case, and the optimal values of fusion parameter in the counting rule under both cases decrease as the local detection threshold increases.

혈관 부착 비골 이식술을 이용한 실패한 족관절 고정술의 치료 (Ankle Arthrodesis with Vascularized Fibular Graft in Failed Ankle Fusion)

  • 정덕환;정재익;임영규
    • Archives of Reconstructive Microsurgery
    • /
    • 제9권2호
    • /
    • pp.134-138
    • /
    • 2000
  • Arthrodesis of the ankle joint is inevitable in the cases of severe arthrosis or defective bony structures around ankle joint. There have been many kinds of arthrodesis methods were introduced. In cases with failed athrodesis with previous arthrodesis surgery and neuropathic joints have difficulty to achieve fusion of joint with conventional methods. Authors underwent four cases of ankle fusion with vascularized fibular graft from 1997 in the cases of three failed fusions and one diabetic neuropatic joint. Two of four performed free vascularized fibular transplantation from contralateral side leg with microvascular anastomosis, two of four performed with pedicled fibular transposition to the ankle joint in same side leg. Three of four cases achieved arthrodesis average 9.2 months after surgery, one case was failed due to vascular thrombosis of the anastomosed site in diabetic neuropathic condition. The result of this technique revealed 75%(three of four) success rate and longer bone union time required. However, in these cases had no recommendable options with conventional bone graft and additional ankle joint fusions procedure because of poor bone quality and defect of distal tibia and talus portions. Free vascualrized fibular transfer to the failed athrodesis of ankle joint is one of the effective alternative methods in failed ankle fusion cases, especially the quality of the bone around previous fusion site is poor.

  • PDF

의사결정 규칙을 이용한 데이터 통합에 관한 연구 (A Study on the Data Fusion Method using Decision Rule for Data Enrichment)

  • 김순영;정성석
    • 응용통계연구
    • /
    • 제19권2호
    • /
    • pp.291-303
    • /
    • 2006
  • 대용량의 데이터로부터 의미있는 지식을 찾는 과정에서 데이터의 질은 무엇보다도 중요하다. 본 연구에서는 데이터의 충실도를 높이기 위한 방법으로 여러 경로로부터 수집된 데이터의 정보를 활용하기 위해 데이터 마이닝 알고리즘인 의사결정 규칙을 이용한 데이터 통합 기법을 제안하고, 실제 데이터를 이용하여 모의실험을 통해 제안된 알고리즘의 효율성을 비교하였다. 실험결과 제안된 알고리즘이 데이터 통합의 성능을 향상시킴을 알 수 있었다.

한국 분청사기 문양과 몬드리안 작품을 이용한 퓨전 직물디자인 개발 (The Development of Fusion Textile Design by Using the Patterns Described in Buncheong Pottery and Mondrian's Works)

  • 정진순
    • 한국의류산업학회지
    • /
    • 제8권5호
    • /
    • pp.505-512
    • /
    • 2006
  • Today a new culture called fusion has been forming. And it is spreading at an alarming rate in our society. When people talk about the character of Korean beauty and Korean culture, they speak taking pottery as an example. We can speak that the pottery is a core of culture which represent our people. And I think its pattern can be a good material for fusion. Also, among many Western artists, Mondrian is an unique painter who is to do with our culture. So, in this study, I chose the patterns described in Buncheong pottery and the Mondrian's works for the development of fusion textile design. Patterns expressed on Buncheong pottery are, for the most part, abstract patterns simplified the shape of object. And the Mondrian's works is the geometrical abstract painting be made by vertical and horizon. Using those I intend to develop the fusion textile designs which mixed Oriental culture and Western culture. Also, I intended to simulate them on ties and clothes and present the possibility of culture merchandise development. The reasons for doing so to let other peoples of the world, know about our excellent culture.

신뢰성 있는 기동 항적 추적을 위한 다중 레이더 융합 알고리즘 (A Multi Radar Fusion Algorithm for Reliable Maneuvering Target Tracking)

  • 조태환;이창호;김진욱;원인수;조윤현;박효달;최상방
    • 한국항행학회논문지
    • /
    • 제15권4호
    • /
    • pp.487-494
    • /
    • 2011
  • 레이더를 이용한 항적 융합 알고리즘은 반드시 필요하며, 이를 통해서 높은 신뢰성을 확보할 수 있다. 본 논문에서는 칼만필터 보다 성능이 좋다고 알려진 IMM(Interacting Multiple Model) 필터를 이용하여 다중 레이더 융합 알고리즘을 제안하였다. 분산형 융합 방식을 적용하였고, 부필터 3개, 주필터 1개를 이용하였다. 성능분석은 등속운동, 가속운동, 선회 등 항공기 기동을 묘사한 가상의 레이더 데이터를 이용하여 분석하였다. 성능분석 결과, 항공기가 기동하는 구간에서도 좋은 추적 성능을 보였다.

Polyethylene Glycol 처리에 의한 생쥐 2세포기배의 분할구 융합에 관한 연구 (Studies on the Polyethylene Glycol-induced Fusion of Two-cell Mouse Embryo Blastomeres)

  • 양부근
    • 한국가축번식학회지
    • /
    • 제14권2호
    • /
    • pp.133-140
    • /
    • 1990
  • This study was conducted to develop a simple and efficient technique for fusing 2-cell mouse embryos to obtain tertraploid embryos. Various concentration of PEG and exposure times were compared in order to determine the best condition for fusion and subsequent of fused embryos. The results obtained were follows ; 1. The incidence of fusion induction treated with 40% PEG(70.8%) and 45%(62.7%) for 60 sec. exposure were higher than those of 40% and 45% PEG for 30 sec., 90 sec., or 120 sec. exposure group. Also, the highest incidence of fusion induction(76.9%) was achieved with 120 sec. exposure at 50% PEG concentration. 2. Fused embryos after PEG treatment were cleavaged 2-to 4-cell, 8-cell, morula and blastocyst at 20-24 hr., 30-34., 44-52 hr., respectively, and were not different from those obtained fleshly. 3. The high proportions of the embryos developed to blastocysts after blastomere fusion with 40% PEG for 60 sec., 45% PEG for 60 sec. and 50% for 120 sec. were 66.7%(42/63), 69.0%(29/42) and 32.0%(16/50), respectively, this trend indicated that the fusion rate was similar to the incidence of fused embryos forming blastocysts. 4. The cell number of blastocyst developed from fused embryos(18.7 2.6) was samller than that of untreated embryos(48.9 1.69)

  • PDF

이부프로펜과 셀룰로오스아세테이트의 고체분산체 제조방법에 따른 물리화학적 성질 및 용출 특성 (Physicochemical Property and Release Behavior of Ibuprofen Solid Dispersion with Cellulose Acetate Prepared with Various Methods)

  • 이은용;오명준;김세호;성경열;이영현;김수진;서한솔;이동원;강길선
    • 폴리머
    • /
    • 제35권2호
    • /
    • pp.113-118
    • /
    • 2011
  • 고체분산체는 난용성약물의 용해도를 향상시키는 기술로 용출특성을 고분자의 성질, 고분자의 함량 및 물리화학적 성질에 의하여 변화한다. 본 연구에서는 이부프로펜과 셀룰로오스 아세테이트를 사용하여 분무건조와 로터리 증발법을 사용하여 고체분산체를 제조하였다. 제조한 고체분산체의 표면성질을 주사전자현미경(SEM)을 사용하여 분석하였으며, X선 회절기(X-RD)와 사치주사열량계(DSC)를 사용하여 결정성 변화를 관찰하였다. 고체분산체의 화학적 변화를 관찰하기 위하여 적외선 분광기(FTIR) 분석을 하였으며, 수분 친화도를 측정하기 위하여 수분접촉각 측정을 하였다. 용출 특성은 인공정액(pH 6.8) 및 인공위액 (pH 1.2)에서 관찰하였다. 실험결과 약물의 결정성은 고분자의 비율이 증가하면 결정성이 감소하였으며, 화학적 변화는 없었다. 수분 친화도는 고분자비율과 비례하였으며, 분무건조로 제조된 고체분산체의 경우가 조금 높은 수분 친화도를 가졌다. 용출실험 결과 인공위액에서는 고분자의 비율이 높아질수록 용출률이 증가하였으며, 인공장액에서의 용출속도는 고분자의 비율과 반비례하는 것을 볼 수 있었다.

Field Inspection of Phase-Array Ultrasonic for PolyEthylene Electrofusion Joints

  • Kil, Seong-Hee;Jo, Young-Do;Yoon, Kee-Bong
    • 한국가스학회지
    • /
    • 제16권1호
    • /
    • pp.22-25
    • /
    • 2012
  • Welding and/or fusion in polyethylene(PE) system made on site is focused on the control of the welding or fusion process to follow proper procedure. The process control is important, but it is not sufficient for the long term reliability of a pipe system. To achieve the rate of failure close to zero, Non Destructive Testing(NDT) is necessary in addition to joining process control. For electrofusion joints several non-destructive testing methods are available. The ultrasonic phased array technique is possible to detect various defects including wire deviations and regions with lack of fusion. In this studies, testing was carried to detect the defect after electrofusion joining of polyethylene piping is utilized by the ultrasonic phased array technique. From testing data, ultrasonic phased array technique is recommended as a reliable non-destructive testing method.

클러터 환경에서 다중센서 정보융합을 통한 유도성능 개선 연구 (A Study of Missile Guidance Performance Enhancement using Multi-sensor Data Fusion in a Cluttered Environment)

  • 한두희;김형원;송택렬
    • 제어로봇시스템학회논문지
    • /
    • 제16권2호
    • /
    • pp.177-187
    • /
    • 2010
  • A MTG (Multimode Tracking and Guidance) system is employed to compensate for the limitations of individual seekers such as RF (Radio frequency) or IIR (Imaging Infra-red) and to improve the overall tracking and guidance performance in jamming, clutter, and adverse weather environments. In the MTG system, tracking filter, data association, and data fusion methods are important elements to maximize the effectiveness of precision homing missile guidance. This paper proposes the formulation of a Kalman filter for the estimation of line-of-sight rate from seeker measurements in missiles guided by proportional navigation. Also, we suggest the HPDA (Highest Probability Data Association) and data fusion methods of the MTG system for target tracking in the adverse environments. Mont-Carlo simulation is employed to evaluate the overall tracking performance and guidance accuracy.

Dual-Stream Fusion and Graph Convolutional Network for Skeleton-Based Action Recognition

  • Hu, Zeyuan;Feng, Yiran;Lee, Eung-Joo
    • 한국멀티미디어학회논문지
    • /
    • 제24권3호
    • /
    • pp.423-430
    • /
    • 2021
  • Aiming Graph convolutional networks (GCNs) have achieved outstanding performances on skeleton-based action recognition. However, several problems remain in existing GCN-based methods, and the problem of low recognition rate caused by single input data information has not been effectively solved. In this article, we propose a Dual-stream fusion method that combines video data and skeleton data. The two networks respectively identify skeleton data and video data and fuse the probabilities of the two outputs to achieve the effect of information fusion. Experiments on two large dataset, Kinetics and NTU-RGBC+D Human Action Dataset, illustrate that our proposed method achieves state-of-the-art. Compared with the traditional method, the recognition accuracy is improved better.