• Tribology and Lubricants
• /
• v.24 no.5
• /
• pp.255-263
• /
• 2008

Adhesion tests were conducted to investigate the adhesion characteristics between mold and thermoplastic polymer film. Coating of anti-sticking layer (ASL), a kind of polymer material, imprint pressure, and separation velocity were considered as the process conditions. A piece of fused silica without patterns on its surface was used as a mold and the thermoplastic polymer films were made on Si substrate by spin-coating the commercial polymer solution such as mr-I PMMA and mr-I 7020. The ASL was derived from (1H, 1H, 2H, 2H - perfluorooctyl) trichlorosilane($F_{13}$-OTS) and coated on the fused silica mold in vapor phase. The pull-off force was measured in various process conditions and the surfaces of the mold and the polymer film were observed after separation. It was found that the adhesion characteristics between the mold and the thermoplastic polymer film and the release performance of ASL were changed according to the process conditions. The ASL was effective to reduce the pull-off force and the damage of polymer film. In cases of the mold coated with ASL, the pull-off force did not depend on imprint pressure and separation velocity.

• Korean Journal of Materials Research
• /
• v.11 no.2
• /
• pp.137-145
• /
• 2001

A new process, gelcasting in aqueous medium, to fabricate complex-shaped ceramic core has investigated. The ceramic slurry, mixture of fused silica powder and additives such as zircon and cordierite, was electrosterically stabilizes. The slip was prepared by ball milling of polydispered ceramic suspension with monomer, dimer and dispersant. The rheological behavior of slip was evaluated by viscosity measurement. It was found that the high solid loading of polydispersed ceramic slip, which has low viscosity of 50vol%, is possible to obtained. The viscosity of the slip was significantly dependent upon the amount of polymer dispersant and the formulation of monomer and dimer. The green bodies were fabricated through casting and gelation at room temperature followed by drying at $25^{\circ}C$ for 48hrs under relative humidity of 80~85%. Crack-free green body was successfully fabricated through the above process.

• Korean Journal of Soil Science and Fertilizer
• /
• v.35 no.3
• /
• pp.162-168
• /
• 2002

The silica uptake of rice plant(Oryza sativa L.) and a potential capacity of paddy soil as a source of silica supply for rice plant was studied under field experimental condition. Amount of Si from irrigation water, rainfall, which was a source of silica supply, and percolating rate of water through paddy soil profile as a source of silica loss from paddy soil, was investigated. Rice plants were grown in three different conditions, which included Control as non-fertilized, RDA's recommandation(NPK, Urea-Fused phophate-Potassium chloride=$110-45-57kg\;ha^{-1}$) and RDA's recommandation with supplement of silicate fertilizer(NPK+Si, Urea-Fused phosphate-Potassium chloride+Si=$110\;N-45\;P_2O_5-57\;K_2O+267.2\;Si\;kg\;ha^{-1}$). An amount of silica supply from rainfall was $0.5kg\;ha^{-1}$ and average amount of silica supplied from irrigation water $42.5kg\;ha^{-1}$, ranging from $28.1kg\;ha^{-1}$ to $58.8kg\;ha^{-1}$. Silica amount percolated through the soil profile have uniform trend comparatively showing $62.9kg\;ha^{-1}$ in Control, $64.8kg\;ha^{-1}$ in NPK treatment and $62.9kg\;ha^{-1}$ in NPK+Si treatment. Silica uptaked by Rice plant was $335.6kg\;ha^{-1}$ in Control, $406.6kg\;ha^{-1}$ in NPK+Si treatment and $471.1kg\;ha^{-1}$ in NPK+Si treatment. The difference between an amount of Si input(from rainfall, irrigation water and silicate fertilizer) and an amount of Si output(percolated Si in soil, uptaked Si by rice plant) was $357.4kg\;ha^{-1}$ in control, $412.1kg\;ha^{-1}$ in NPK treatment and $238.2kg\;ha^{-1}$ in NPK+Si treatment. Results of our study imply that paddy soil is a potential pool as a source of Si supply during growing periods of rice plant.

• Journal of the Korean Ceramic Society
• /
• v.35 no.1
• /
• pp.23-32
• /
• 1998

Al2O3/Al composites were produced by immersing the sintered silica preform in molten aluminum which contained magnesium as impurity. Three distinct regions existed in the penetration behavior of molten me-tal with changing the reaction temperature. These regions are denoted as low temperature regime(75$0^{\circ}C$-85$0^{\circ}C$) intermediate regime(90$0^{\circ}C$-95$0^{\circ}C$) and high temperature regime(100$0^{\circ}C$$\leq$) In the low temperature regime the penetration speed of molten aluminum increased with increasing reaction temperature whereas it decreased in the intermediate regime due to the phase transition of alumina formed by displacement reac-tion. In the high temperature regime the penetration speed of molten aluminum was the highest at 100$0^{\circ}C$ which was 3.6 mm/hr But above 105$0^{\circ}C$ molten aluminum did not penetrate into the silica preform because of the formation of a dense spinel layer at the preform surface by magnesium in molten Al.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.158-158
• /
• 2008

모바일 정보통신기기를 중심으로 실장모듈의 초소형화, 고집적화로 인해 접속단자의 피치가 점점 미세화 됨에 따라 플립칩 본딩용 접착제에 함유되는 무기충전제인 실리카 필러의 크기도 미세화되고 있다. 본 연구에서는 NCP (non-conductive paste)의 실리카 필러의 크기가 COB(chip-on-board) 플립칩 패키지의 신뢰성에 미치는 영향을 조사하였다. 실험에 사용된 실리카 필러는 Fused silica 3 종과 Fumed silica 3종이며 response surface 실험계획법에 따라 혼합하여 최적의 혼합비를 정하였다. 테스트베드로 사용된 실리콘 다이는 투께 $700{\mu}m$, 면적 5.2$\times$7.2mm로 $50\times50{\mu}m$ 크기의 Au 도금범프를 $100{\mu}m$ 피치, peripheral 방식으로 형성시켰으며, 기판은 패드를 Sn으로 finish 하였다. 기판을 플라즈마 전처리 후 Panasonic FCB-3 플립칩 본더를 이용하여 플립칩 본딩을 수행하였다. 패키지의 신뢰성 평가를 위해 $-40^{\circ}C{\sim}80^{\circ}C$의 열충격시험과 $85^{\circ}C$/85%R.H.의 고온고습시험을 수행하였으며 Die shear를 통한 접합 강도와 4-point probe를 통한 접속저항을 측정하였다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.552-554
• /
• 2004

Barrier ribs of plasma display panel (PDP) are glass matrix composite reinforced with alumina particles. Mechanical properties of the ribs are very crucial for the improvement in reliability of the panel as the ribs might fracture during transportation and service. In this study, therefore, the effects of filler type and content on the mechanical properties of the ribs were investigated. The fillers used include $Al_2O_3$, $TiO_2$, $ZrO_2$ and fused silica. The content of the filler was changed from 0 to 40 vol.%. The mechanical properties of the ribs measured were hardness, Young's modulus, fracture toughness, and 3-point bending modulus. The fracture toughness evaluated by micro-Vicker's indentation of the composites, in general, was measured to increase with the content of the filler until the sintered density does not decrease significantly. The improvement, however, was dependent on the type of filler employed.

• Journal of Environmental Science International
• /
• v.12 no.4
• /
• pp.477-480
• /
• 2003

Pesticides were extracted from samples with 70% acetone and methylene chloride in order, and then cleaned up via open-column chromatography apparatus packed with florisil, and finally analyzed simultaneously the organochlorine and pyrethroid pesticides using GC(ECD). An ultra-2 fused silica capillary column was used to separate and identify the products. The resolution between the last isomeric peak of cypermethrin(59.987min) and the first isomeric peak of flucythrinate(60.043min) was not satisfactory. The last isomeric peak of fenvalerate(62.344min) and the first isomeric peak of fluvalinate(62.397min) were overlapped. Recoveries of soybean sample fer the most pesticides were 73.3% to 102.4%. Detection limits were between 0.004 and 0.063 ${\mu}$g/mg when this method was used.

• Korean Journal of Materials Research
• /
• v.17 no.6
• /
• pp.303-307
• /
• 2007

ZnO thin films were prepared by pulsed laser deposition on amorphous fused silica substrates at different ambient $O_2$ pressures varying from 0.5 to 500 mTorr, to observe the effect of ambient gas on their crystalline structure, morphology and optical properties. Results of X-ray diffraction, scanning electron microscopy, atomic force microscopy and photoluminescence studies showed that crystallinity, surface features and optical properties of the films significantly depended on the oxygen background pressure during growth. A low oxygen pressure (0.5 mTorr) seems to be suitable for the growth of highly c-axis oriented and smoother films possessing a superior luminescent property. The films grown at the higher $O_2$ pressures (50-500 mTorr) were found to have many defects probably due to an excessive incorporation of oxygen into ZnO lattice. We speculate that the film crystallinity could be affected by the kinetics of atomic arrangement during deposition at the higher oxygen pressures.

• Journal of the Korean Chemical Society
• /
• v.28 no.4
• /
• pp.244-250
• /
• 1984

Separation and identification of the polycyclic aromatic compounds (PAC) from pyrolysis products of cellulose and lignin were performed using a combination of acid-base solvent partitioning and silicic acid column chromatography with fused-silica capillary column gas chromatography/ mass spectrometry. Sixteen PAC were positively identifited by retention indices and mass spectra data. Both materials produced the same kinds of PAC. But lignin produced much more PAC than cellulose. Almost no highly carcinogenic heterocyclic PAC containing nitrogen and sulfur were produced.

• Mass Spectrometry Letters
• /
• v.4 no.4
• /
• pp.83-86
• /
• 2013

A new interface for coupling CIEF and MS using a four-way cross has been developed in a single mechanical system. This new interface could be operated without the electric discontinuity and reinstallation of lines. Additionally, a bare fused silica capillary was facilitated as a spray needle to produce electrospray and to guide catholyte or sheath liquid. Focusing for CIEF was completed in a hanging droplet at the end of spray needle. This capillary spray needle also provided stable spray, enhanced the ionization efficiency and increased sensitivity. Results with carbonic anhydrase I showed that focusing and spraying were well completed with the new interface and the new spray needle.