• Journal of the Korean Ceramic Society
• /
• v.52 no.5
• /
• pp.338-343
• /
• 2015

To prevent an interfacial reaction between the anode and the electrolyte layer during the conventional high-temperature co-firing process, an anode-supported type cell with a thin-film electrolyte was fabricated by low-temperature ceramic thick film coating process. Ni-GDC cermet composite was used as the anode material and YSZ was used as the electrolyte material. Open circuit voltage and maximum power density were found to strongly depend on the surface uniformity of the anode functional layer. By optimizing the microstructure of the anode functional layer, the open circuit voltage and maximum powder density of the cell increased to 1.11 V and $1.35W/cm^2$, respectively, at $750^{\circ}C$. When a GDC barrier layer was applied between the YSZ electrolyte and the LSCF cathode, the cell showed good stability, with almost no degradation up to 100 h. Anode-supported type SOFCs with high performance and good stability were fabricated using a coating process.

• Advances in aircraft and spacecraft science
• /
• v.7 no.4
• /
• pp.353-369
• /
• 2020

This paper presents the flutter analysis and optimum design of axially functionally graded box beam cantilever wing section by considering various geometric and material parameters. The coupled dynamic equations of the continuous model of wing system in terms of material and cross-sectional properties are formulated based on extended Hamilton's principle. By expressing the lift and pitching moment in terms of plunge and pitch displacements, the resultant two continuous equations are simplified using Galerkin's reduced order model. The flutter velocity is predicted from the solution of resultant damped eigenvalue problem. Parametric studies are conducted to know the effects of geometric factors such as taper ratio, thickness, sweep angle as well as material volume fractions and functional grading index on the flutter velocity. A generalized surrogate model is constructed by training the radial basis function network with the parametric data. The optimized material and geometric parameters of the section are predicted by solving the constrained optimal problem using firefly metaheuristics algorithm that employs the developed surrogate model for the function evaluations. The trapezoidal hollow box beam section design with axial functional grading concept is illustrated with combination of aluminium alloy and aluminium with silicon carbide particulates. A good improvement in flutter velocity is noticed by the optimization.

• Journal of the Korean Ceramic Society
• /
• v.54 no.1
• /
• pp.9-22
• /
• 2017

Many new functional materials have been studied for efficient production and storage of energy. Many new materials such as sodium-based and sulfide-based materials have been proposed for energy storage, but research on Li batteries is still dominant. Due to the influence of environmental concerns regarding nuclear energy, interest in and research on fusion power are steadily increasing. For the commercialization of nuclear fusion, a design standard based on a considerable level of physical analysis and modeling is proposed. Nevertheless, limitations of existing materials in nuclear fusion environments limit practical applications. Tritium propagation material for continuous fusion reaction is one of the core materials, and therefore research on this material is being carried out intermittently. The key material for Li-based energy storage and tritium generation is the functional material Li-M-O. In this review, a structural description of functional Li-M-O system materials and technical trends for its applications are introduced.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.524-524
• /
• 2012

Thermal Barrier Coating (TBC)은 미사일, 로켓발사체와 같이 고온에 노출되는 장비를 열로부터 보호하기 위한 코팅이다. 일반적인 Thermal Barrier Coating (TBC)은 모재와 코팅층간의 낮은 접합력과 높은 열충격으로 인한 박리가 많이 나타난다. 그래서 접합력을 높이고, 열충격을 줄이기 위해 모재와 코팅층 사이에 본드코팅층을 만든 Duplex - Thermal Barrier Coating (Duplex-TBC)이 개발되었다. 그러나 Duplex - Thermal Barrier Coating (Duplex-TBC)은 금속재료인 본드코팅층과 세라믹재료인 탑코팅층 사이에서 박리가 많이 발생한다. 이러한 문제점을 해결하기 위해 두 가지 분말을 동시에 코팅하여 본드코팅과 탑코팅의 경계가 없는 Functional Gradient Material - Thermal Barrier Coating (FGM-TBC)의 연구가 필요하다. 본 연구에서는 Functional Gradient Material - Thermal Barrier Coating (FGM-TBC)의 열충격 특성에 미치는 진공 플라즈마 용사 조건의 영향을 조사하였다. Functional Gradient Material - Thermal Barrier Coating (FGM-TBC)는 진공 플라즈마 용사장치를 사용하여 Cu-Cr 합금위에 코팅하였다. 거리, Carrier gas flow, 그리고 챔버 내부의 압력을 달리하여 제조하였다. 사용한 분말은 본드코팅용으로 Amdry 962와 내열 세라믹코팅을 위해 204NS를 사용하였고, 각각 분말 공급조건을 조절하여 두 분말의 비율을 달리하였다. 제조한 Functional Gradient Material - Thermal Barrier Coating (FGM-TBC) 코팅은 전기로에서 50분간 가열한 후, 수조에서 10분간 냉각하는 열충격 실험을 통해 열차폐 성능을 평가 하였다. 이러한 과정에서 진공 플라즈마 용사 조건 및 FGM 조성과 비율이 내열충격 특성에 미치는 영향을 미세조직학적 관점에서 고찰하였다.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.4
• /
• pp.907-912
• /
• 2009

Complex breakup behavior in the revival wave has been observed in the Belousov-Zhabotinsky(BZ) reaction system containing 1,4-cyclohexanedione (1,4-CHD) in the dish divided into two compartments with a sliding window. A same reaction mixture is poured into the two compartments individually with time difference. Wave propagation exhibited different behavior in the revival wave of the reaction system. This was largely dependent on the progress time prior to the pouring into each compartment and on the gap between the times of pouring into the two compartments. The revival wave in the reaction system is induced spontaneously as a new wave train with a long time lag after the disappearance of the initially induced wave. A thoroughgoing study of the chaotic breakup of propagating chemical wave train was to be possible since the revival wave has a longer wavelength, clearer wave-train patterns, and longer duration period.

• Journal of Applied Biological Chemistry
• /
• v.55 no.2
• /
• pp.71-77
• /
• 2012

Many of biochemical or physiological processes can be regulated by non-coding RNAs as well as coding RNAs in plants, animals and microbes. Recently, many small RNAs including microRNAs (miRNAs) and endogenous small interference RNAs (siRNAs) and long non-coding RNAs have been discovered from ubiquitous organisms including plants. Biotic and abiotic stresses are main causal agents of crop losses all over the world. Much efforts have been performed for understanding the complex mechanism of stress responses. Up to date, many of these researches have been related with the identification and investigation of stress-related proteins, showing limitation to resolve the complex mechanism. Recently, non-coding RNAs as well as coding genes have been gradually interested because of its potential roles in plant stress responses as well as other biophysical aspects. In this review, various potential roles of non-coding RNAs, especially miRNAs and siRNAs, are reviewed in relation with plant biotic and abiotic stresses.

• Journal of Applied Biological Chemistry
• /
• v.53 no.3
• /
• pp.132-138
• /
• 2010

A gene encoding a putative alanine racemase in B. pseudomycoides was cloned and expressed in Escherichia coli BL21(DE3) using a pET-21 vector harbouring 6xHistidine tag. Affinity purification of the recombinant alanine racemase with a nickel resin resulted in one band by SDS-PAGE analysis. The purified enzyme showed a molecular weight of 46 kDa. The enzyme was the most active toward L-alanine and secondly D-alanine, implying that the enzyme is an alanine racemase. D-cysteine significantly inhibited the enzyme activity and also L-cysteine to a lesser extent. The enzyme was considerably activated by addition of pyridoxal-5'-phosphate (PLP), showing that 73% increase in activity was observed at 0.3 mM, compared to control. The enzyme was the most active at pH 9.0 and more stable at alkaline pHs than acidic pHs.

• Macromolecular Research
• /
• v.17 no.5
• /
• pp.285-288
• /
• 2009

• Korean Journal of Crystallography
• /
• v.19 no.1
• /
• pp.1-6
• /
• 2008

The reaction of dilithio-o-carborane with dipenyl disulfide produces a phenyl thiolated o-carborane and it has been confirmed that there is conformational similarity between the structure of the compound elucidated by X-ray crystallography and that calculated by ab initio and density functional theory.

• Journal of Information Display
• /
• v.11 no.3
• /
• pp.95-99
• /
• 2010

A series of new dielectric polymers with phenyl, epoxy, and carboxylicacid functional groups was prepared via free-radical polymerization. The effect of such dielectric polymers with various functional groups on the performance of OTFT was investigated. The nonpolar groups of terpolymer made the surface of the dielectric layer more hydrophobic and improved the crystal growth of pentacene on the gate insulator, resulting in higher mobility. By controlling the functional group, the electric characteristics of OTFT performance was varied, with $0.00017-0.15\;cm^2/V{\cdot}s$ mobility.