• Journal of the Society of Naval Architects of Korea
• /
• v.46 no.2
• /
• pp.127-135
• /
• 2009

The performance of the waterjet system of 180 ton class fishing guard ship has been experimentally studied. A waterjet propulsion system has many advantages in comparison with a conventional screw propeller especially for high speed craft because of its good cavitation performance. Recently waterjet system has been applied to fishing boats and fishing guard ship because of avoiding a net problem although their speeds are not so high. This paper describes experimental procedure and analysis method of resistance and self-propulsion tests with a 1/14.46-scale model. Experimental results were analyzed according to ITTC 96 standard method. The full-scale effective power and delivered power of the ship were also analyzed and the full-scale speed predicted from the model test results shows a good agreement with the full-scale result from the sea trial tests.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.8 no.6
• /
• pp.589-601
• /
• 2016

The hybrid grid was adopted and numerical prediction analysis of propeller unsteady bearing force considering free surface was performed for mode and full-scale KCS hull-propeller-rudder system by employing RANS method and VOF model. In order to obtain the propeller velocity under self-propulsion point, firstly, the numerical simulation for self-propulsion test of full-scale ship is carried out. The results show that the scale effect of velocity at self-propulsion point and wake fraction is obvious. Then, the transient two-phase flow calculations are performed for model and full-scale KCS hull-propeller-rudder systems. According to the monitoring data, it is found that the propeller unsteady bearing force is fluctuating periodically over time and full-scale propeller's time-average value is smaller than model-scale's. The frequency spectrum curves are also provided after fast Fourier transform. By analyzing the frequency spectrum data, it is easy to summarize that each component of the propeller bearing force have the same fluctuation frequency and the peak in BFP is maximum. What's more, each component of full-scale bearing force's fluctuation value is bigger than model-scale's except the bending moment coefficient about the Y-axis.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.11 no.1
• /
• pp.33-43
• /
• 2019

A comparison between sea trial measurements and full-scale CFD results is presented for two self-propelled ships. Two ships considered in the present study are: a general cargo carrier at Froude number $F_n=0:182$ and a car carrier at $F_n=0:254$. For the general cargo carrier, the propeller rotation rate is fixed and the achieved speed and trim are compared to sea trials, while for the car carrier, the propeller rotation rate is adjusted to achieve the 80% MCR. In addition, three grids are used for each ship in order to assess the grid refinement sensitivity. All simulations are performed using the Naval Hydro pack based on foam-extend, a community driven fork of the OpenFOAM software. The results demonstrate the possibility of using high-fidelity numerical methods to directly calculate ship scale flow characteristics, including the effects of free surface, non-linearity, turbulence and the interaction between propeller, hull and the flow field.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.10 no.3
• /
• pp.413-420
• /
• 2018

This paper documents the result of a preliminary analysis on the influence of hull-ice friction coefficient on model resistance and power predictions and their correlation to full-scale measurements. The study is based on previous model-scale/full-scale correlations performed on the National Research Council - Ocean, Coastal, and River Engineering Research Center's (NRC/OCRE-RC) model test data. There are two objectives for the current study: (1) to validate NRC/OCRE-RC's modeling standards in regarding to its practice of specifying a CFC (Correlation Friction Coefficient) of 0.05 for all its ship models; and (2) to develop a correction methodology for its resistance and propulsion predictions when the model is prepared with an ice friction coefficient slightly deviated from the CFC of 0.05. The mean CFC of 0.056 and 0.050 for perfect correlation as computed from the resistance and power analysis, respectively, have justified NRC/OCRE-RC's selection of 0.05 for the CFC of all its models. Furthermore, a procedure for minor friction corrections is developed.

• Journal of the Society of Naval Architects of Korea
• /
• v.47 no.2
• /
• pp.178-187
• /
• 2010

The performance of the waterjet system of a patrol boat has been experimentally studied. A waterjet propulsion system has many advantages comparing with a conventional screw propeller especially for high speed craft because of its good cavitation performance. This paper describes experimental procedure and analysis method of self-propulsion tests with a 1/12-scale model. Experimental results were analyzed according to ITTC 96 standard method. The full-scale effective power and delivered power of the ship were also analyzed and the full-scale speed predicted from the model test compares reasonably with the measured full-scale results of the sea trial.

• Journal of the Society of Naval Architects of Korea
• /
• v.51 no.3
• /
• pp.231-238
• /
• 2014

In this study, the self-propulsion tests are performed in INHA towing tank. And the effective wake characteristics of the KVLCC2 and the KCS models are compared by the experimental results. The form factor is independent of Reynolds number. To estimate the hydrodynamic performance of a full scale ship, the form factor is determined to consider attendant on Reynolds number. In this research, the power predictions are carried out considering the form factor difference of model and full scale ship. The results of this research could be used as one of the fundamental data to the powering performance prediction.

• Journal of the Society of Naval Architects of Korea
• /
• v.48 no.3
• /
• pp.222-232
• /
• 2011

This article examines the scale effect of the flow characteristics, resistance and propulsion performance on a 317k VLCC. The turbulent flows around a ship in both towing and self-propulsion conditions are analyzed by solving the Reynolds-averaged Navier-Stokes equation together with the application of Reynolds stress turbulence model. The computations are carried out in both model- and full-scale. A double-body model is applied for the treatment of free surface. An asymmetric body-force propeller is used. The speed performances including resistance and propulsion factors are obtained from two kinds of methods. One is to analyze the computational results in model scale through the revised ITTC' 78 method. The other is directly to analyze the computational results in full scale. Based on the computational predictions, scale effects of the resistance and the self-propulsion factors including form factor, thrust deduction fraction, effective wake fraction and various efficiencies are investigated. Scale effects of the streamline pattern, hull pressure and local flow characteristics including x-constant sections, propeller and center plane, and transom region are also investigated. This study presents a useful tool to hull-form and propeller designers, and towing-tank experimenters to take the scale effect into consideration.

• Journal of the Society of Naval Architects of Korea
• /
• v.46 no.2
• /
• pp.136-147
• /
• 2009

The computational prediction method of speed performance for a ship with vortex generators is proposed. The Reynolds averaged Navier-Stokes equation has been solved together with the application of Reynolds stress turbulence model. The computations are carried out under identical conditions of the experimental method, i.e., towing and self-propulsion calculations without and with vortex generators. The speed performance in full scale is obtained through analyzing the computational results in model scale according to the revised model-ship performance analysis method of ITTC'78 with considering the vortex generators into account. The characteristics of resistance, self-propulsion and wake characteristics on the propeller plane are investigated. The proposed computational prediction clearly shows the effect of vortex generators and can be applicable to the design tool for vortex generators.

• Journal of Ship and Ocean Technology
• /
• v.10 no.4
• /
• pp.1-11
• /
• 2006

The finite volume based multi-block RANS code, WAVIS developed at MOERI is applied to the numerical self-propulsion test. WAVIS uses the cell-centered finite volume method for discretization of the governing equations. The realizable $k-{\epsilon}$ turbulence model with a wall function is employed for the turbulence closure. The free surface is captured with the two-phase level set method and body forces are used to model the effects of a propeller without resolving the detail blade flow. The propeller forces are obtained using an unsteady lifting surface method based on potential flow theory. The numerical procedure followed the self-propulsion model experiment based on the 1978 ITTC performance prediction method. The self-propulsion point is obtained iteratively through balancing the propeller thrust, the ship hull resistance and towing force that is correction for Reynolds number difference between the model and full scale. The unsteady lifting surface code is also iterated until the propeller induced velocity is converged in order to obtain the propeller force. The self-propulsion characteristics such as thrust deduction, wake fraction, propeller efficiency, and hull efficiency are compared with the experimental data of the practical container ship. The present paper shows that hybrid RANS and potential flow based numerical method is promising to predict the self-propulsion parameters of practical ships as a useful tool for the hull form and propeller design.

• Journal of the Society of Naval Architects of Korea
• /
• v.56 no.2
• /
• pp.109-116
• /
• 2019

This paper carried out numerical analysis for estimating the propulsion performance of the model scale ONRT benchmark model of'Tokyo 2015 a workshop on CFD'. The method reflecting the scale effect of ITTC'78 method and form factor were used to compare the estimates of the effective wake ratio of full-scale. The numerical calculation was performed with Siemens's Star-CCM+, compared with IIHR model tests and the numerical analysis results of other research institutes, showing good agreement. In the case of an open stern and twin skeg ship, the validity of the ITTC'78 method can be confirmed by assuming that the effective wake ratio estimated from the numerical analysis results of model scale is similar to the effective wake ratio of full-scale.