• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.3
• /
• pp.1095-1104
• /
• 2013

The number of vehicles registered in Korea is rapidly increasing and will reach 18.26 million as of June 2011. The rapid increase of large-size passenger cars and RVs among this number is causing damage to other vehicles when parked in currently installed parking lots, increased civil complaints from the damage, and inconveniences to people trying to pass through parking lots as well. In particular, the car-stoppers indiscriminately installed at the parking lots are also causing accidents and adding to parking problems, causing economic losses. Accordingly, there should be new regulations for the amount of parking space per vehicle and for locations to install the car-stoppers. The research has first reviewed the distribution ratio of vehicle models from home and abroad for the width and length of the vehicles by each model, parking space per vehicle where the car-stoppers are installed and examples of changes in distribution ratio. In addition, the amount of parking space per vehicle was calculated with consideration for various specifications by each car model. As a result, margin width of full sized car is decreased by 18~21mm on the existing width. This is judged decreases accident of parking lot, because length of the front of car is not deviate parking Space Section. In conclusion, presented improvement ideas for parking plans with enhanced convenience and safety from the aspect of the drivers. Parking lot relevant businesses will also be maximized in terms of cost and efficiency when the criteria for the structure of parking lots and their installation is established and the improved parking plan is applied in the future.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.5
• /
• pp.48-53
• /
• 2012

A non-linear vehicle model and an observer are designed to observe the yaw rate and the body side slip angle when a vehicle is turning maneuver in this study. The developed vehicle model is a full car model and has fourteen degree of freedom. A Luenberg observer is applied to develop the observer. The vehicle model is validated with a reference result and shows good accordance. The observer is tested on dry asphalt, wet asphalt and snow paved road. The results prove the performance of observer is robust and reliable.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.8
• /
• pp.863-867
• /
• 2011

In this paper, we analyze the characteristic test results of an MR damper for a cruise bus, and we model the nonlinear hysteretic characteristics of the damper using arctangent and polynomial functions. We establish an experimental model of the MR damper according to the input current, and we set the model parameters using the MATLAB Optimization Toolbox. The model is verified via a computer simulation of a full-car model.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.6
• /
• pp.14-22
• /
• 2010

In this study, a large bus is tested for measuring the steering response based on the slarom test and step steer test. A full car model by using ADAMS/Car is established for computer simulation. For bus modeling, user defined templates are made and used in the simulation. Simulation results according to the slarom and step steer test are compared to the physical experiments, in which several sensors are installed to measure vehicle responses. The results obtained from the comparison show a good agreement with regard to the vehicle velocity and steering angle.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.1
• /
• pp.105-111
• /
• 2015

Since 2007, Insurance Institute of Highway Safety(IIHS) has conducted the new bumper test using bumper barrier to estimate the repair cost of impacted vehicle. In this study, for the front body FE model of a medium size passenger car analyzes were carried out to optimize the shape of backbeam center reinforcement bracket. First, overlap effect was examined with changing the overlap magnitude and spot welds were added along the backbeam center line for reducing the section shear deformation. Next, for an overlap model design parameter study was performed for the bracket. Thickness effect was examined and an inner reinforcement was added to the bracket. Also, the lower part of bracket was deleted and additionally the bracket length was extended. The results were discussed in terms of backbeam backward deflection, barrier backstop intrusion and weight. Compared with the current design, the final model showed 44.1% bracket weight reduction with 30.0% decrease of backbeam deflection.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.16 no.1
• /
• pp.105-111
• /
• 2003

Wheel for passenger car support the car weight with tires, and they transmit rolling and braking power into the ground. Whittling away at wheel weight is more effective to boost fuel economy than lighting vehicle body structure. A shape of hole in disk is optimized for minimizing the weight of steel wheel. Pro/ENGINEER program is used for formulating the design model, and ANSYS package is selected for analyzing the design model. It has difficulties to interface these commercial software directly. For Combining both programs, response surface methodology is applied to construct approximation functions for maximum stresses and maximum displacements are obtained by full factorial design of five levels. This steel wheel is modeled in 14-inch diameter of rim, and wide parameter of hole in disk is only selected as design variable for reducing the weight of steel whee. PLBA(Pshenichny-Lim-Belegundu-Arora) algorithm, which used the second-order information in the direction finding problem and uses the active set strategy, is used for solving optimization problems.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.1
• /
• pp.109-118
• /
• 2005

A functional suspension model is proposed as a kinematic describing function of the suspension that represents the relative wheel displacement in polynomial form in terms of the vertical displacement of the wheel center and steering rack displacement. The relative velocity and acceleration of the wheel is represented in terms of first and second derivatives of the kinematic describing function. The system equations of motion for the full vehicle dynamic model are systematically derived by using velocity transformation method of multi-body dynamics. The comparison of field test results and simulation results of the ADAMS/Car demonstrates the validity of the proposed functional suspension modeling method. This model is suitable for real-time vehicle dynamics analysis.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.3 s.174
• /
• pp.691-700
• /
• 2000

This paper presents a novel type of a semiactive damper featuring an electro-rheological(ER) fluid. Unlike conventional cylindrical ER damper, the proposed one has controllable orifices by the intensity of electric fields (We call it orifice type). The dynamic model of the orifice type ER damper is formulated by incorporating field-dependent Bingham properties of an arabic gum-based ER fluid. Design parameters such as electrode gap are subsequently determined on the basis of the dynamic model. After manufacturing the orifice type ER damper, field-dependent damping forces and damping force controllability are empirically evaluated. In the evaluation procedure, conventional cylindrical ER damper is adopted and its performance characteristics are compared with those of the orifice type ER damper. In addition, the proposed one is installed with a full-car model and its vibration control performance associated with a skyhook controller is investigated.

• Proceeding of EDISON Challenge
• /
• 2016.03a
• /
• pp.246-255
• /
• 2016

When spring of the suspension is exerted by an external load, a car should be designed to prevent predictable damages and designed for a ride comfort. We used experiments design to design VON-MISES STRESS and K, a constant, of spring of suspension which is installed in a car as a goal level. We analyzed the result from Edison's Elastic - Plastic Analysis SW(CSD_EPLAST) by setting D, d, n as external diameter of coil, internal diameter of coil, the number of total coil respectively. The experiment design let the outcome be as Full-second order by using Box-Behnken which is one of response surface methods. Experimented and analyzed results based on the established experiments design, We found out design parameter which has desired VON-MISES STRESS and the constant K. Additionally, we predicted life time of when the external load was exerted by repeated load by using fatigue equation, and verification of plastic deformation has also been made. Additionally we interpreted a model, which is formed by optimized design parameter, with linear analysis and non-linear analysis, at the same time we also analyzed plastic deformation with the values from the both models. Finally, we predicted fatigue life of optimized model by using fatigue estimation theory and also evaluated a ride comfort with oscillation analysis.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.5
• /
• pp.22-28
• /
• 2011

This paper presents an active roll motion control of a passenger vehicle. The roll controller is designed in the framework of $H_{\infty}$ control scheme based on the 3 DOF vehicle model taking into consideration parameter variations, which affect the roll dynamics, and unmodeled high frequency dynamics for robustness and performance. In order to investigate the feasibility of the active roll control system in a car, its performance is evaluated by simulation in a full vehicle model with nonlinear tire characteristics under various operating conditions. Finally, in order to enhance the performance in a transient region taking into account the limited bandwidth of the actuating module, a hybrid control strategy is presented.