• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.957-967
• /
• 2017

Firing test of the fuel grain for solid fuel ramjet with additives and ignition support material was conducted. Fuel grain consist of HTPB mixed with AP particle 15 wt.%, Boron particle 5 wt.%. To cause the short ignition delay, ignition support consist of $NC/BKNO_3$ and composite propellant was coated to the fuel grain. An oxidant gas having a controlled temperature, pressure and oxygen composition close to the air condition in the ramjet combustor was supplied using the Ethanol blended $H_2O_2$ gas generator. Gas was set to flow at a mass flow rate of 150 g/s and mass flux of $200kg/m^2s$ in the grain port. Through the test, ignition support operated well and ignition delay of 0.5. During the test, stable chamber pressure with 8 bar and high combustion efficiency of 0.86 was confirmed.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.145-148
• /
• 2009

Combustion tests of a fuel-rich gas generator had been conducted using the assembly of a powerpack. A gas generator is prone to longitudinal modes of combustion instabilities in a powerpack due to the increase of a characteristic length. It has been observed that the orifice inserted at the exit of the gas generator suppresses a longitudinal combustion instability. The intensities of pressure fluctuations in the manifolds and the chamber increase quadratically with a chamber pressure. Pressure fluctuations in the fuel manifold reveal two-fold strength greater than those in the oxygen manifold and the chamber. Frequency analysis indicates nonlinear characteristics inherent in the pressure fluctuations in the fuel manifold.

• Journal of Microbiology and Biotechnology
• /
• v.20 no.7
• /
• pp.1092-1100
• /
• 2010

Bacteria, fungi, and protozoa inhabiting the rumen, the largest chamber of the ruminants' stomach, release large quantities of hydrogen during the fermentation of carbohydrates. The hydrogen is used by coexisting methanogens to produce methane in energy-yielding processes. This work shows, for the first time, a fundamental possibility of using a hydrogen-rich fermentation gas produced by selected rumen ciliates to feed a low-temperature hydrogen fuel cell. A biohydrogen fuel cell (BHFC) was constructed consisting of (i) a bioreactor, in which a hydrogen-rich gas was produced from glucose by rumen ciliates, mainly of the Isotrichidae family, deprived of intra- and extracellular bacteria, methanogens, and fungi; and (ii) a chemical fuel cell of the polymer-electrolyte type (PEFC). The fuel cell was used as a tester of the technical applicability of the fermentation gas produced by the rumen ciliates for power generation. The average estimated hydrogen yield was ca. 1.15 mol $H_2$ per mole of fermented glucose. The BHFC performance was equal to the performance of the PEFC running on pure hydrogen. No fuel cell poisoning effects were detected. A maximum power density of $1.66\;kW/m^2$ (PEFC geometric area) was obtained at room temperature. The maximum volumetric power density was $128\;W/m^3$ but the coulombic efficiency was only ca. 3.8%. The configuration of the bioreactor limited the continuous operation time of this BHFC to ca. 14 h.

• Journal of Advanced Marine Engineering and Technology
• /
• v.26 no.1
• /
• pp.37-47
• /
• 2002

Recently gasoline direct injection method has been applied to gasoline engine to reduce fuel consumption rate by controlling fuel air mixture on lean condition by means of stratified charging, and to reduce simultaneously. Pollutant emissions especially NOx and CO by lowering the combustion temperature. But difficulty of controling local fuel air ratio at ignition area in flammability limit unavoidably appeared, because it is merely controlled by injection timing with spatial and temporal distribution of fuel mixture. In this study, the authors devised a uniquely shaped combustion chamber so called three-chamber GDI engine, intended to keep the more reliable fuel air ratio at ignition area. The combustion chamber is divided into three regions. The first region is in the rich combustion division, where the fuel is injected from the fuel injection valve and ignited by the spark plug. The second region is in the lean combustion division, where the combustion gas from the rich combustion division flows out and burns on lean condition. And the last region is in the main combustion division ie in the cylinder, where the gas from the above two combustion divisions mixed together and completes the combustion during expansion stroke. They found that the stable range of operation of three-chamber GDI engine on low-load condition exists in the lean area of average equivalence ratio. And they also found that the reformed engine reveals less specific fuel consumption and less pollutant emissions compared with conventional carburettor type gasoline engine.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.05a
• /
• pp.258-261
• /
• 2003

The optimal design and combustion analysis of the gas generator for Liquid Rocket Engine (LRE) were performed. A fuel-rich gas generator in open cycle turbopump system was designed for 101on1 in thrust with RP-1/LOx combination. The optimal design was done for maximizing specific impulse of main combustion chamber with constraints of combustion temperature and power matching in turbopump system. Results of optimal design show the dimension of length, diameter, and contraction ratio of gas generator. The configuration of the gas generator and the condition for performance which can maximize the objective function were determined and found to meet the design constraints. Also, the combustion analysis was conducted to evaluate the performance of designed chamber and injector of gas generator. And the effect of the turbulence ring was investigated on the mixing enhancement in the chamber.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.3
• /
• pp.7-12
• /
• 2003

Mixture formation in the cylinder of a lean bum engine has been observed by Laser Induced Fluorescence technique. XeCl laser (308nm) was used to produce a laser sheet. 3-pentanone has been added to iso-octane fuel to produce fluorescence, the intensity of which is proportional to the concentration of the fuel. The laser sheet was introduced through the piston window and the fuel distribution in the vertical plane was observed through a side window. Comparison has been made for the cases of selected fuel injection timing as 0, 360, 405, and 450 CA. For the case of 0 and 360 CA injection, uniform fuel distribution in the combustion chamber has been obtained at the ignition time which is favorable for the high load mode. And the late injection cases, 405 and 450 CA, revealed the stratified formation of rich mixture around the spark plug. That extends the lean misfire limit and reduces cyclic variation in the low load mode.

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.1
• /
• pp.88-95
• /
• 1999

This study investigates the effects of different kind fuels on the flame structure by using the numerical simulation in triple flame made by a co-flowing fuels-air stream based on the elementary chemical reaction mechanism. Methane and Hydrogen were used as fuel for this study. In order to interpret the result of the study on numerical simulation Skeletal chemistry is employe as the elementary chemical reaction mechanism for methane Gutheil's as an offset ele-mentary chemical reaction mechanism for hydrogen. The result of this study is as follows. In com-parison between the apparent burning velocity change of triple flame and the one-dimensional pre-mixed flame hydrogen fuel flame is higher than methane fuel flame. The flame thrusts out for-ward in the down stream of the boundary between air-fuel mixture and air stream and a part of the flow is bent and forks out in this protruding flame so that a triple flame is originated.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.6
• /
• pp.9-16
• /
• 2006

Variable valve timing is one of the attractive ways to control homogeneous charge compression ignition (HCCI) engine. Hot internal residual gas which can be controlled by variable valve timing(VVT) device, makes fuel evaporated easily, and ignition timing advanced. Regular gasoline was used as main fuel and di-methyl ether(DME) was used as ignition promoter in this research. HCCI engine operating range is limited by high combustion peak pressure and engine noise. High combustion pressure can damage the engine during operation. To avoid engine damage, the rich limits have to define using various methods. Peak combustion pressure, rate of cylinder pressure rise was considered to determine rich limit of engine operating range. Knock probability was correlated with the rate of cylinder pressure rise as well as the peak combustion pressure.

• 한국연소학회:학술대회논문집
• /
• 2004.11a
• /
• pp.213-216
• /
• 2004

The results of combustion performance test of fuel-rich gas generator(GG) using LOx and kerosene as propellant at design and off-design point are described. The parameters used in this analysis are the average exit temperature($T_{GG}$) and the characteristic velocity($C^{\ast}$). The average gas temperature at the exit of gas generator is found to be a function of propellant O/F ratio. For the gas generator having residence time of 4msec or more, the effect of flame residence time and combustion chamber pressure on the exit temperature is not significant. The exit characteristic velocity is found to be linearly proportional to the gas temperature at the exit of gas generator.

• Journal of the Korean Society of Combustion
• /
• v.15 no.4
• /
• pp.9-14
• /
• 2010

Numerical simulations of freely propagating fuel-rich $CH_4/CH_3Cl$ premixed flames were performed at atmospheric pressure in order to understand the effect of the oxygen enrichment on the production of PAH. A chemical kinetic mechanism was used, which involved 157 gas-phase species and 1693 forward reactions. The calculated flame speeds were compared with the experiments for the flames established on the equivalence ratios of 1~1.6, the results of which were in good agreement. As the level of oxygen enrichment was increased, the concentrations of one or four ring aromatic hydrocarbons were decreased. This might cause the fact that the contribution of PAH species to soot was weakened.