• 한국수소및신에너지학회논문집
• /
• 제32권5호
• /
• pp.340-346
• /
• 2021

The initial electrochemical performance of ceramic fuel cell with thin-film electrolyte fabricated by plasma-enhanced atomic layer deposition method was evaluated in terms of peak power density ratio, open circuit voltage ratio, and activation/ohmic resistance ratios at 500℃. Hydrogen and air were used as anode fuel and cathode fuel, respectively. The peak power density ratio reduced as ~52% for 30 min, which continually decreased as time increased but degradation rate gradually decreased. The open circuit voltage ratio decreased with respect time; however, its behavior was evidently different from the reduction behavior of the peak power density. The activation resistance ratio increased as ~127% for 30 min, which was almost similar with the reduction behavior of the peak power density ratio.

• 대한기계학회논문집B
• /
• 제34권9호
• /
• pp.835-841
• /
• 2010

MEMS 가스터빈 엔진에서 연료와 공기의 혼합에 영향을 미치는 중요한 요소중 하나는 연료 분사구 형상의 설계이다. 본 연구에서는 3 개의 연료 주입부와 각 주입부에 연결된 여러 개의 분사구에 의해 연료와 공기가 혼합되는 시스템을 고려하여 분사구의 배열과 연료 공급비율의 변화에 따른 혼합 정도를 당량비를 통하여 정량적으로 해석하였다.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2001년도 제23회 KOSCO SYMPOSIUM 논문집
• /
• pp.97-103
• /
• 2001

The characteristics of flame stability have been studied experimentally using a slot burner. The blowout conditions of a fuel-lean premixed laminar flame, which is located in the middle of fuel-rich premixed laminar flames, are identified for propane, ethylene, and methane flames. The fuel-rich flames could stabilize the fuel-lean flame for the equivalence ratio as low as 0.2. The laminar flame speed along with the heat release rate is likely to be the important factor in stabilizing a fuel-lean flame. The increase of heat release rate on a fuel-rich flame lowers the equivalence ratio limit for the stable fuel-lean flames. The stability of fuel-lean flames, however, was not sensitive to the equivalence ratio of a fuel-rich flame.

• 대한기계학회논문집B
• /
• 제27권11호
• /
• pp.1548-1562
• /
• 2003

This paper is the first of several companion papers which compare the methods of Air-fuel ratio determination. There are many methods which calculate Air-Fuel ratio from exhaust emission. Most of them are based on the simple chemical equations, which use balance of atom, and the error of the calculation is negligible as far as the instrumentation accuracy is guaranteed. They assume homogeneous mixture and complete combustion to the extent of oxygen availability. Because of these simple assumptions, they cannot offer the information about the fuel distribution state and the malfunction of instrument. For these limitations, Eltinge offered new one based on stricter mathematical model. This result coincides with the others very well and gives more information about the mixture state and instrumentation. Consequently this might be a general solution for Air-fuel ratio determination and exhaust composition. The objects of the calculation, however, were not commercial fuels except gasoline and the compensation method of unburned hydrocarbon was not appropriate to recent analyzer. Moreover he did not consider the fuel which contains oxygen, such as methanol, ethanol and blend of gasoline-alcohol. In this paper, Eltinge chart is expanded to the arbitrary fuel composition as the reference exhaust compositions for the purpose of further discussions about Air-fuel ratio determination methods and the charts fur gasoline, diesel, methanol, M85, liquefied petroleum gas(LPG), natural gas(NG), propane, butane are illustrated.

• 한국수소및신에너지학회논문집
• /
• 제23권1호
• /
• pp.93-99
• /
• 2012

The investigation of clean and environment-friendly coal utilization technology is actively progressed due to high oil price and serious climate change caused by greenhouse gas emissions. In this study, the plasma gasification was performed using a 6kW microwave plasma unit under various reaction conditions: the particle sizes of coal ($45{\mu}m-150{\mu}m$), $O_2$/fuel ratio (0 - 1.3), and steam/fuel ratio (0 - 1.5). The $H_2$ composition decreases with decreasing coal particle size. With increasing $O_2$/fuel ratio, the $H_2$ composition in the syngas decreased while the $CO_2$ composition increased. As the steam/fuel ratio increased from 0 to 1.5, the $H_2$ composition in the syngas increased while the $CO_2$ composition decreased. From the results, it was proven that the variation of syngas composition greatly affected by $O_2$/fuel ratio than steam/fuel ratio. The $H_2$ composition in the syngas, carbon conversion, and cold gas efficiency increased with increasing plasma power.

• 한국분무공학회지
• /
• 제26권2호
• /
• pp.81-87
• /
• 2021

This study was performed to calculate the swirl ratio of a diesel engine intake port by a 1D computer simulation under actual engine operating conditions. The swirl ratio of the intake port was simulated according to the change of the engine speed during the operation of the motoring without fuel injection. The swirl ratio of the intake port was simulated according to changes in the crank angle during the four-cycle operation of intake, compression, expansion and exhaust. The swirl ratio represented by the three regions of the piston, center and squish was simulated. Among the three regions, the piston-region swirl ratio is important for effective air-fuel mixing in the engine cylinder. In particular, it was confirmed during the simulation that the piston swirl ratio before and after the compression top dead center (TDC) point when fuel is injected in the DI diesel engine can have a significant effect on the mixing of air and fuel. It was desirable to set the average piston swirl ratio over a crank angle section before and after compression TDC as the representative swirl ratio of the cylinder head intake port according to the change of the engine speed.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.3435-3439
• /
• 2007

The aim of this study is to find out the condition that generates maximum $H_2$ through the calculation of equilibrium model with conditions of pyrolysis gases of Refuse Plastic Fuel(RPF). This study deals with the computational simulation of a RPF gasification using an equilibrium model based on minimization of the Gibbs free energy. An equilibrium analysis was carried out to determine species composition of Syngas in RPF gasification and reactions to variation of temperature, $O_2$/Fuel ratio and Steam/Fuel ratio. Calculated results showed that $O_2$/Fuel ratio, Steam/Fuel ratio and temperature affected on mole fraction of $H_2$, CO.

• 동력기계공학회지
• /
• 제11권1호
• /
• pp.51-55
• /
• 2007

A study on combustion characteristics using emulsified fuel in a diesel engine were performed experimentally. In this paper, the experiments were performed at engine speed 1800rpm, emulsion ratios were 0%, 10%, 20%, and main measured items were specific fuel consumption, cylinder pressure, rate of pressure rise, rate of heat release etc. The obtained conclusions were as follows. 1) Specific fuel consumption increased maximum by 19.8% at low load, but was not affected at full load. 2) Rate of pressure rise and rate of heat release were about the same in the case of 10% and 20% of emulsion ratio. 3) Cylinder Pressure increased 9.6%, rate of pressure rise increased 53.4% in case of emulsion ratio 20% at full load. 4) Rate of heat release increased 72.4% in case of emulsion ratio 20% at full load.

• 한국자동차공학회논문집
• /
• 제6권6호
• /
• pp.252-258
• /
• 1998

In a SI engine, it is necessary to control fuel quantity in accordance with intake air amount in order to reduce exhaust emission and improve the specific fuel consumption. Generally the map data is used for the vehicles with a SI engine. For the precise control of air-fuel ratio, the real time control method is recommended rather than the control method using map data. In this paper, we developed real time control system using microprocessor and IBM-PC, and applied it to the commercial SI engine. We got good results for air-fuel ratio under the idle condition.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2012년도 제45회 KOSCO SYMPOSIUM 초록집
• /
• pp.29-30
• /
• 2012

The objectives of this study are to examine the variation of flame chemiluminescence on flame condition and to evaluate the possibility to apply the optical sensor for air/fuel ratio control. Flame chemiluminescence is one of the most important factor to judge the real time flame condition like a air/fuel ratio. In this paper, it is experimentally found that a strong relationship between the air/fuel ratio and optical element output (i.e., photo diode) should be existed. This is verified through the flame spectral analysis for various PD output signal.