• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.866-867
• /
• 2011

As part of the green growth, The Green Car has attracted wide attention. Types of the Green Car are Electric Vehicle, Plug-in Hybrid Electric Vehicle, Hybrid Electric Vehicle, Fuel Cell Vehicle and Clean Diesel Vehicle. Of these, The electric vehicle is equipped with the BDU(Battery Disconnecting Unit). BDU is supplying stable battery power and blocking it to protect electrical system of the electric vehicle. The BDU consists of electric components such as current sensor, fuse and pre-charge resistor. These must pass Voltage withstand test, Salt mist test, Thermal shock test, Vibration test and Short-circuit test commonly to verify reliability of the electric components. In addition, The current sensor should be verified whether normal operation. The breaking capacity of fuse should be verified. The durability of pre-charge resistor should be verified by supplying battery power and blocking it repeatedly. The reliability of BDU as well as the electric vehicle is secured by verifying the reliability of electric components. In addition, It will contribute to the acceleration and promotion of Green Car Technology.

• 자동차안전학회지
• /
• 제8권2호
• /
• pp.30-36
• /
• 2016

According to revolutionary developments in automobile technologies, various electronically controlled components of vehicles are rapidly increasing. A variety of advanced vehicles (hybrid vehicle, hydrogen fuel-cell vehicle, electric vehicle, etc.) using electrical energy source are increasing, too. The electromagnetic compatibility is getting more important for development of a vehicle because those advanced vehicles are equipped with more new electronic systems. In general, electromagnetic compatibility tests consist of an electromagnetic interference (EMI) test and an electromagnetic susceptibility (EMS) test. In this paper, in order to investigate the electromagnetic interference in the cabin of vehicle by various electric and electronic components of vehicles, a series of narrowband electromagnetic emission tests are conducted. For comparison, the several digital home appliances (smartphone under charging, laptop compuer and digital camera), which are used a lot in daily lives, are tested.

• 전기학회논문지
• /
• 제65권12호
• /
• pp.2197-2210
• /
• 2016

Recently, the trend of zero emissions has increased in automotive engineering because of environmental problems and regulations. Therefore, the development of battery electric vehicles (EVs), hybrid/plug-in hybrid electric vehicles (HEVs/PHEVs), and fuel cell electric vehicles (FCEVs) has been mainstreamed. In particular, for light-duty electric vehicles, improvement in electric motor performance is directly linked to driving range and driving performance. In this paper, using an improved design for the interior permanent magnet synchronous motor (IPMSM), the EV driving range for the light-duty EV was extended. In the electromagnetic design process, a 2D finite element method (FEM) was used. Furthermore, to consider mechanical stress, ANSYS Workbench was adopted. To conduct a vehicle simulation, the vehicle was modeled to include an electric motor model, energy storage model, and regenerative braking. From these results, using the advanced vehicle simulator (ADVISOR) based on MATLAB Simulink, a vehicle simulation was performed, and the effects of the improved design were described.

• 한국항공우주학회지
• /
• 제41권3호
• /
• pp.233-239
• /
• 2013

화학수소화합물 수소저장방법을 이용한 100 W 급 연료전지 시스템을 소형 무인항공기의 추진시스템으로 적용하는 연구를 수행하였다. 소형/경량 수소 발생 제어장치와 연료전지/배터리 하이브리드 전력 공급 방법으로 효율성 및 안정성을 증대하였다. $NaBH_4$ 수용액을 이용한 수소 발생장치와 Dead-end 형식의 PEMFC를 이용한 연료전지 시스템의 지상, 비행 시험이 수행되었다. 연료전지 스택을 안정적으로 운전하고, 높은 효율을 얻기 위해 45 kPa의 압력을 가하는 방법을 적용하였다. 수소 발생 시스템 내부 압력을 이용한 수소 발생 제어 장치는 45~55 kPa 사이에서 유지되며 안정적으로 수소가 공급되는 것을 확인하였다. 그 결과, 100 W 연료전지 시스템이 소형 무인항공기 적용하기에 무게 및 소비 전력을 만족함을 확인하였고, 시험비행을 통해 성능을 입증하였다.

• Journal of Electrical Engineering and Technology
• /
• 제12권5호
• /
• pp.1891-1901
• /
• 2017

In this paper, optimal control of the fuel cell and design of a high-efficiency power converter is implemented to build a high-priced fuel cell system with minimum capacity. Conventional power converter devices use a non-isolated boost converter for high efficiency while the battery is charged, and reduce its conduction loss by using MOSFETs instead of diodes. However, the efficiency of the boost converter decreases, since overshoot occurs because there is a moment when the body diode of the MOSFET is conducted during the dead time and huge loss occurs when the dead time for the maximum-power-flowing state is used in the low-power-flowing state. The method proposed in this paper is to adjust the dead time of boost and rectifier switches by predicting the power flow to meet the maximum efficiency in every load condition. After analyzing parasite components, the stability and efficiency of the high-efficiency boost converter is improved by predictive compensation of the delay component of each part, and it is proven by simulation and experience. The variation in switching delay times of each switch of the full-bridge converter is compensated by falling time compensation, a control method of PWM, and it is also proven by simulation and experience.

• 한국자동차공학회논문집
• /
• 제22권7호
• /
• pp.135-143
• /
• 2014

Electrified vehicles can be classified with hybrid electric vehicles, battery electric vehicles and fuel cell electric vehicles. These vehicles have two more than energy converters which are the part of a powertrain. It is particularly difficult to estimate the power of hybrid electric vehicles due to two different energy converters with different power characteristics. Therefore, a new power concept for these vehicles is needed. The vehicle power as the new concept for solving this problem was defined in this study. The test method and the procedure were made a development in this study. Four electrified vehicles with different electric fraction were used to validate the method. Two percentage of COV was suggested as a criterion for the maximum vehicles power based on the previous studies. The repeatability of this method was within ${\pm}2$ per cent for the maximum vehicle power and within ${\pm}5$ per cent for the vehicle speed at maximum vehicle power.

• 전기전자학회논문지
• /
• 제24권2호
• /
• pp.610-618
• /
• 2020

본 논문에서는 규칙기반 알고리즘을 이용한 수소연료전지/배터리 하이브리드 철도차량 모델링을 제시한다. 모터의 운전영역에 따른 토크 곡선을 계산하여 견인 시스템의 구동 전력을 결정하고 철도차량의 각 운전 모드에 적용하여 전기 시스템을 모델링 한다. 전기 시스템의 전력은 규칙기반 알고리즘을 이용한 에너지 관리시스템(Energy Management System, EMS)으로 결정한다. 배터리의 충전상태(State Of Charge, SOC)에 따라 운전 영역을 세분화하여 수소 소비량을 효율적으로 관리한다. 제안하는 철도차량 모델링의 타당성은 MATLAB/Simulink 시뮬레이션을 통해 검증한다.

• 한국추진공학회지
• /
• 제14권6호
• /
• pp.1-8
• /
• 2010

본 논문에서는 PAV에 쓰이는 전기추진 시스템에 대해서 기술하고 동력시스템에 대한 분석, 무게산정을 통하여 PAV 추진시스템으로서의 전기추진시스템을 살펴보았다. 연료전지와 배터리를 같이 사용 하는 전기추진의 경우 아직은 내연기관만큼 성능을 내진 못하지만 에너지 밀도가 약 0.75 kW$^*$hr/kg, 출력밀도는 약 2.5 kW/kg 정도까지 성능이 나온다면 기존의 내연기관을 대체할 수 있을 것으로 예상된다. 연료전지와 배터리 등을 이용한 친환경적인 전기추진 방식은 요즘 주된 관심사인 소음 공해 문제를 해결할 수 있는 훌륭한 해결책이 될 수 있을 것이라 생각된다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 춘계학술대회 논문집
• /
• pp.911-915
• /
• 2007

This paper deal with the design concept of traction motor for Bimodal low floor vehicles that are CNG(Compressed Natural Gas) hybrid bus and Fuel-cell bus. The design concept of the traction motor is studied in terms of electrical characteristics and mechanical construction. Finally, this paper introduces the characteristic of the traction motor for low floor vehicles which are applied in the world, and mentioned the detail design concept of traction motor.

• 한국자동차공학회논문집
• /
• 제24권6호
• /
• pp.694-701
• /
• 2016

According to revolutionary developments in automobile technologies, eco-friendly advanced vehicles (hybrid vehicle, hydrogen fuel-cell vehicle, electric vehicle, etc.) are rapidly increasing. The electromagnetic compatibility is getting more important for development of a vehicle because those advanced vehicles are driven by electric energy and equipped with more electric systems. In general, electromagnetic compatibility tests consist of an electromagnetic interference(EMI) test and an electromagnetic susceptibility(EMS) test. EMI test of the electric vehicles are needed not only in driving mode but also in charging mode because they must be recharged by much electric energy for driving. Depending on vehicle manufacturers, the charging device type and the location of charging device inlet in electric vehicles are various. In this paper, in order to investigate EMI of electric vehicles in charging mode in consideration of the direction of measuring antenna and the location of charging device inlet, a series of electromagnetic emission tests are conducted using three electric vehicles (neighborhood electric vehicle, electric vehicle and electric vehicle-bus). The test results show that electromagnetic emission measurements in charging mode are dependent on the direction of measuring antenna and the location of charging device inlet.