• 한국자동차공학회논문집
• /
• 제7권8호
• /
• pp.116-122
• /
• 1999

According to the stringent exhaust emission regulation, precise control of air fuel ratio is one of the most important issues on gasoline engine. Although many researches have been carried out to identify the fuel transport phenomena in a port fueled gasoline engine, complexity of fuel film behavior in the intake port makes it difficult. The fuel film behavior was investigated recently by using visualization method and these gave us qualitative understanding. The purpose of this study is to estimate of wall wetting fuel in the intake port and the inducted fuel mass was predicted by using wall wetting fuel model . The model coefficient($\alpha$,$\beta$) and fuel film mass on the port wall were determined from measured in-cylinder HC concentration using FRFID after injection off. The fuel film mass was increased, but $\alpha$(ratio of directly inducted fuel mass into cylinder from injected fuel mass) was decreased with increasing load at the same engine speed. $\beta$is nearly constant value(0.8~0.9). when injected fuel mass is varied at 1500rpm , the calculated air fuel ratio using well wetting fuel model was nearly the same as measured by UEGO.

• Nuclear Engineering and Technology
• /
• 제51권2호
• /
• pp.345-355
• /
• 2019

Use of the reconstructed fuel assemblies from partially burnt nuclear fuel pins is analyzed. This reutilization option is a potential candidate technique to make better use of the nuclear resources. Standard two step method is used to calculate node i.e. fuel assembly average burnup and then pin by pin ${\eta}$ values are reconstructed to ascertain the residual reactivity in the used fuel pins. Fuel pins with ${\eta}$ > 1:0 are used to reconstruct to-be-reused fuel assemblies. These reconstructed fuel assemblies are burnt during the cycle 3, 4, 5 and 6 of a 1000 MW PWR core by replacing fresh, once burnt and twice burnt fuel assemblies of the reference core configurations. It is concluded that using reconstructed fuel assemblies for the fresh fuel affect dearly on the cycle length (>50 EFPD) when more than 16 fresh fuel assemblies are replaced. However, this loss is less than 20 days if the number of fresh fuel assemblies is less than eight. For the case of replacing twice burned fuel, cycle length could be increased slightly (10 days or so) provided burnt fuel pins from other reactors were also available. Reactor safety parameters, like axial off set (< ${\pm}10%$), Doppler temperature coefficient (<0), moderator temperature coefficient at HFP (<0) are always satisfied. Though, 2D and 3D pin peaking factors are satisfied (<1:55) and (<2:52) respectively, for the cases using eight or less reconstructed fuel assemblies only.

• 동력기계공학회지
• /
• 제12권2호
• /
• pp.12-17
• /
• 2008

Biodiesel fuel(BDF) which is easily produced from vegetable oils such as soybean oil and rice bran oil can be effectively used as an alternative fuel in diesel engine. But biodiesel fuel can affect the performance and emissions in diesel engine because it has different chemical and physical properties from diesel fuel. To investigate the combustion characteristics of biodiesel fuel as an alternative fuel for D.I. diesel engine, the experiments were carried out at the three-cylinder, four stroke D.I. diesel engine with T/C. Experimental parameters adopted a conventional diesel fuel and a blend of biodiesel fuel derived from soybean. As a result of experiments in a test engine, BSFC with blend of BDF resulted in higher than with diesel fuel. The ignition delay decreased with blend of BDF than with diesel fuel.

• 한국대기환경학회지
• /
• 제14권2호
• /
• pp.107-116
• /
• 1998

Coal gasification fuel has generally a lower calorific values than natural gas and also contains ammonia which is a main source of fuel NOx. Such a fuel is in need of the advanced technologies for the NOx reduction with higher combustion efficiency. Therefore fuel staged combustion was investigated for the fuel NOx control using a bench scale gas combustoi for the fuel NOx control. Parametric screening studies were performed with the variation of air ratio, retention length and reburning fuel. The NOx reduction efficiency was increased with an increase of total air ratio having optimum reburning air ratio differently, The Increased retention length of the reburning zone was preferable for NOx reduction. Hydrocarbonic reburning fuels like propane and butane were more effective for the NOx reduction efficiency than hydrogen fuel. The NOx concentration at exit was linearly increased according to the fuel-N the fuel.

• 한국자동차공학회논문집
• /
• 제9권4호
• /
• pp.112-120
• /
• 2001

Poor fuel vaporization in gasoline engines causes the problem of HC emission during the cold start and warm-up period. This paper presents a strategy to improve fuel atomization during the warm-up phase. In this experiment, the heated fuel-rail system is constructed to investigate the effects of fuel heating on the average size of fuel droplets. The fuel atomization effects are examined by measuring Sauter Mean Diameter (SMD) of the fuel droplets from the three different types (two-hole, pintle, and six-hole) of injectors based upon a returnless heated fuel-rail system. The results show that the six-hole type injector is the most sensitive to fuel heating in terms of SMD among three different types of injectors.

• 전기학회논문지
• /
• 제60권11호
• /
• pp.2043-2048
• /
• 2011

High speed drive method for a fuel injector cleaner with current control is presented in this paper. The fuel injector cleaner is used for cleaning the fuel injectors in vehicles when it is clogged with deposit and rust. The fuel injector cleaner cleans the fuel injector by turning on and off the fuel injector rapidly. When the fuel injectors are cleaned, the switching speed is very important. However, when the fuel injector is turned off, the residual current in the fuel injector coil slows down the return action of the plunger in the fuel injector deteriorating performance and speed of the fuel injector cleaner. In this paper, fast turn off operation method of fuel injectors is developed for more effective cleaning. The simulation and experiment results show the validity of the proposed method.

• 한국자동차공학회논문집
• /
• 제11권1호
• /
• pp.72-78
• /
• 2003

Recently, lots of researchers have been attracted to develope various alternative fuels and to use renewable fuels as a solution of environmental problems from automobile. The use of biodiesel fuel is an effective way of substituting diesel fuel in the long nun. It is a domestically produced, renewable fuel that can be manufactured from vegetable oils, used vegetable oils, or animal fats. In this study, the usability of biodiesel fuel derived from rice ban oil, one of the oxygenated fuels as an alternative fuel for diesel engines was investigated in IDI diesel engine. Emissions were characterized with neat biodiesel fuel and with a blend of biodiesel fuel and conventional diesel fuel. Since the biodiesel fuel includes oxygen of about 11%, it could influence the combustion process strongly. So, the use of biodiesel fuel resulted in lower emissions of carbon monoxide and smoke emissions with some increase in emissions of oxides of nitrogen. It is concluded that biodiesel fuel can be utilized effectively as a renewable fuel for IDI diesel engine.

• 대한원격탐사학회지
• /
• 제23권1호
• /
• pp.21-32
• /
• 2007

Fire fuel map is one of the most critical factors for planning and managing the fire hazard and risk. However, fuel mapping is extremely difficult because fuel properties vary at spatial scales, change depending on the seasonal situations and are affected by the surrounding environment. Remote sensing has potential to reduce the uncertainty in mapping fuels and offers the best approach for improving our abilities. Especially, Hyperspectral sensor have a great potential for mapping vegetation properties because of their high spectral resolution. The objective of this paper is to evaluate the potential of mapping fuel properties using Hyperion hyperspectral remote sensing data acquired in April, 2002. Fuel properties are divided into four broad categories: 1) fuel moisture, 2) fuel green live biomass, 3) fuel condition and 4) fuel types. Fuel moisture and fuel green biomass were assessed using canopy moisture, derived from the expression of liquid water in the reflectance spectrum of plants. Fuel condition was assessed using endmember fractions from spectral mixture analysis (SMA). Fuel types were classified by fuel models based on the results of SMA. Although Hyperion imagery included a lot of sensor noise and poor performance in liquid water band, the overall results showed that Hyperion imagery have good potential for wildfire fuel mapping.

• Nuclear Engineering and Technology
• /
• 제37권4호
• /
• pp.317-326
• /
• 2005

The burning-out of excess plutonium from the reprocessing of spent nuclear fuel and from the dismantlement of nuclear weapons is recently emphasized due to the difficulties in securing the final repository for the spent fuel and the necessity to consume the ex-weapons plutonium. An irradiation test in the Halden reactor was launched by the OECD Halden Reactor Project (HRP) to investigate the in-pile behavior of plutonium-embedded fuel as a form of mixed oxide (MOX) and of inert matrix fuel (IMF). The first cycle of irradiation was successfully accomplished with good integrity of test fuel rods and without any undesirable fault of instrumentations. The test results revealed that the MOX fuel is more stable under irradiation environments than IMF. In addition, MOX fuel shows lower thermal resistance due to its better thermal conductivity than IMF. The on-line measured in-pile performance data of attrition milled MOX fuel are used in the analysis of the in-pile performance of the fuel with the fuel performance code, COSMOS. The COSMOS code has been developed for the analysis of MOX fuel as well as $UO_2$ fuel up to high burnup and showed good capability to analyze the in-reactor behavior of MOX fuel even with different instrumentation.

• 방사성폐기물학회지
• /
• 제20권1호
• /
• pp.119-126
• /
• 2022

This study provides technical information about the nuclear fuel handling process, which consists of various subprocesses starting from new fuel receipt to spent fuel shipment at a nuclear power plant and the design requirements of fuel handling equipment. The fuel handling system is an integrated system of equipment, tools, and procedures that allow refueling, handling and storage of fuel assemblies, which comprise the fuel handling process. The understanding and reaffirming of detailed code requirements are requested for application to the design of the fuel handling and storage facility. We reviewed the design requirements of the fuel handling equipment for its adequate cooling, prevention of criticality, its operability and maintainability, and for the prevention of fuel damage and radiological release. Furthermore, we discussed additional technical issues related to upgrading the current code requirements based on the modification of the fuel handling equipment. The suggested information provided in this paper would be beneficial to enhance the safety and the reliability of the fuel handling equipment during the handling of new and spent fuel.