• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.8
• /
• pp.1577-1584
• /
• 2002

This paper develops a finite element model for studying the occupant behavior and injury cofficients of a large-sized cab-over type truck. Since it does not have a room to absorb collision energy and deformation in front of the passenger compartment the deformation is directly transmitted to the passenger compartment. Moreover, since its steering column is attached on the frame, severe deformation of the frame directly affects on the steering wheel's movement. Therefore, if the occupant behavior and injury coefficients analysis is performed using a finite element model developed based on a sled test, it is very difficult to expect acquiring satisfactory results. Thus, the finite element model developing in this paper is based on the frontal crash test in order to overcome the inherent problems of the sled test based model commonly used in the passenger car. The occupant behavior and injury coefficients analysis is performed using PAM-CRASH installed in super-computer SP2. In order to validate the reliability of the developed finite element model, a frontal crash test is carried out according to a test method used fur developing truck occupant's secondary safety system in european community and japan. That is, test vehicle's collision direction is vertical to the rigid barrier and collision velocity is 45kph. Thus, measured vehicle pulses at the lower parts of the left and right B-pilla., dummy chest and head deceleration profiles, HIC(head injury criterial) and CA(chest acceleration) values, and dummy behavior from the frontal crash test are compared to the analysis results to validate reliability of the developed model.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.1
• /
• pp.153-161
• /
• 2002

This paper develops a finite element model for crashworthiness analysis ova small-sized bus. The full vehicle finite element model is composed of 31,982 shell elements,599 beam elements,42 bar elements, and 34,204 nodes. The model uses four material models (such as elastic, elastic-plastic(steel), rigid. and elastic-plastic (rubber) material model) of PAM-CRASH. The model uses four contact types to define sliding interfaces in ten areas. A frontal crash test using an actual vehicle with 30mph velocity to a rigid barrier is carried out. Vehicle pulses at lower part of left and right b-pillar are measured, and deformed shapes of frame and driver seat's lower left area are photographed. A frontal crash simulation using the developed full vehicle finite element model is performed with PAM-CRASH installed in super computer SP2. The simulation is performed with the same conditions as the test. The measured vehicle pulses and photographed deformed shapes from the test are compared to ones from the simulation to validate the reliability of the developed model.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.9
• /
• pp.203-211
• /
• 1999

The research committee for automobile repairs (RCAR), an international body of insurance research centers, has adopted the typical low speed crash test based on an average damage level in crash accidents to estimate the damageability , repairability and safety. The characteristics of body acceleration and the probability of injury are investigated based on damaged components, accelerations of body and injured dummy to analyze damageability and the driver's safety under low speed crash environment. It is found from the experimental results that the probability of head and thorax injuries are very low comparing to the injury criteria of FMVSS No.208. Furthermore, it is suggested that the deployment of airbag may not be necessary at RCAR low speed frontal crash test.

• Journal of Biomedical Engineering Research
• /
• v.24 no.1
• /
• pp.15-21
• /
• 2003

In this study, for a safetv assessment of light weight wheelchair occupant in frontal crash, we tested a dynamic sled impact test. we carried out total 6 times test and impact speed was 20g/48 km/h. By using Hybrid III 50%ile male dummy, head injury criteria(HIC), neck flexion moment, neck axial tension force, neck shear force. chest acceleration, head, wheelchair and knee excursion were measured, we evaluated light weight wheelchair occupant safety by motion criteria(MC) which proposed in SAE J2249 and combined injury criteria(CIC) which is a voluntary standard(GM-IARV) of General Motors Co.. when we assumed that the maximum injury value in frontal crash was 100%, the result of motion criteria(MC) of wheelchair occupant was 52%, occupant upper body injury index(CIC) was 60.1%.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.5
• /
• pp.72-77
• /
• 2007

Since 2000, sports utility vehicles(SUVs) occupy about 40% of domestic vehicle sales. As sports utility vehicle sales are increased the probability of crash accident between SUVs and passenger vehicles increases. Generally, SUVs are heavier than passenger vehicles and their drive height and front end stillness are higher than passenger vehicles. Because of these characteristics SUVs cause more severe injury and fatal injury in SUV to passenger vehicle head-on impact. To evaluate SUV's aggessivity to passenger vehicle, we carried out SUV to passenger vehicle head-on crash test. And finally the way how to reduce incompatibility between SUVs and passenger vehicles is suggested.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.4
• /
• pp.234-241
• /
• 2002

In this study, the car crash analysis that simulates the crushing behavior of car forestructure during a frontal impact is carried out. The analysis model for front impact of a car consists of the lumped mass and the spring model. The characteristics value of masses and springs is obtained from the static analysis of a target car. The deceleration-time curve obtained from the simulation are compared with NCAP test data from the NHTSA. They show a good agreement with frontal crash test data. The deceleration-time curve of passenger compartment is classified into 3 stages; beginning stage, middle stage, and last stage. And the behavior of masses at each stage is explained. The effect of stiffness variation on deceleration of passenger compartment is resolved. The maximum loaded peak-time of torque box and dash is the main factor to control the passenger compartment's maximum deceleration.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.2
• /
• pp.189-197
• /
• 1996

In this study, the crashworthiness analysis was carried out for the hat type section side rails which had an important role of absorbing the impact energy during frontal crash. In case of a tapered hat type section model, numerical simulation models and test models were designed with varing design variables; welding pitch, taper angle, initiator shape, initiator location. The effect of variation of the design variables was investigated by quasi-static and dynamic test and numerical simulation.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.6
• /
• pp.190-194
• /
• 2006

This research investigates vehicle structure acceleration and vehicle deformation with RCAR crash test. To investigate vehicle damage characteristics in an individual case, it is possible to RCAR low speed crash test. In this study, two tests were conducted to evaluate difference between RCAR new condition and RCAR old condition. A two large vehicles were subjected to a frontal crash test at a speed of 15km/h with an offset of 40% $10^{\circ}$ angle barrier and flat barrier. The results of the 15km/h with an offset of 40% $10^{\circ}$ angle barrier revealed high acceleration value on the vehicle structure and high repair cost compared to the RCAR 15km/h with an offset of 40% flat barrier. So in order to improve damage characteristics in low speed crash of vehicle structure and body component of the monocoque type passenger vehicles, the end of front side member and front back beam should be designed with optimum level and to supply the end of front side member as a partial condition approx 300mm.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.4
• /
• pp.420-427
• /
• 2015

This paper statistically reviewed for the USNCAP frontal crash test results carried out by NHTSA. Vehicle samples were selected on total 20 vehicles which were included on 15 vehicles for MPV&SUV and 5 Pickup. The results was summarized as followings. The performance for the driver was better than the passenger's in the average sense. There exist distinctions between the driver and the passenger on the USNCAP front test procedure, for example dummy size, seating position and airbag style. Therefore these differences originated in the statistical results. Main effect was Neck injury for crash performance on both dummies on the average value. Root cause of neck injury was different for each dummy, ie, the driver caused from Nte & Ntf, but the passenger did absolutely Nte mode. Reliability evaluated from the standard deviation was highly dependent upon chest injury on the driver and neck injury on the passenger. Restraint system was also summarized.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.6
• /
• pp.8-15
• /
• 2013

Wide range frequency pulses occur in a car crash test. Until now, low frequency under 400Hz has been used to determine an airbag deployment criteria. Also, FIS (Front Impact Sensor) has been used to detect the crash pulse in early stage. Nowadays, technology to determine an airbag delpoyment criteria by using a high frequency crash pulse without FIS is being focused on. In this paper, the signal transmissibility of high frequency pulse for two different cars was studied. Also, signal transfer test of high frequency pulse was done by using a high speed ball impact. Signal runtime of the frontal impact is compared with that of the side impact. The signal transmissibility difference due to the car structure difference was discussed and structure change for improving the signal transmissibility was proposed.