• 소성∙가공
• /
• 제19권8호
• /
• pp.494-501
• /
• 2010

The main objective of this study is to examine the sensitivity of calibration curves of FEA of ring compression test to frictional shear factor. Ring compression test has been investigated by measuring dimensional changes at different positions of ring specimen and they include the changes in internal diameter at the middle and top section of the specimen, outer diameter at the middle and top section, surface expansion at the top surface, respectively. Initial ring geometries employed in analysis maintain a fixed ratio of 6 : 3 : 2, i.e. outer diameter : inner diameter : thickness of the ring specimen, which is generally known as 'standard' specimen. A rigid plastic material for different work-hardening characteristics has been modeled for simulations using rigid-plastic finite element code. Analyses have been performed within a definite range of friction as well as over whole range of friction to show different sensitivities to the interfacial friction for different ranges of friction. The results of investigation in this study have been summarized in terms of a dimensionless gradient. It has been known from the results that the dimensional changes at different positions of ring specimen show different linearity and sensitivity to the frictional condition on the contact surface.

• Tribology and Lubricants
• /
• 제30권4호
• /
• pp.240-245
• /
• 2014

Low alloy heat resistant brake disk and sintered brake pad are applied to mechanical brake system for the speed-up of urban rapid transit. In this research, we analyzed how the frictional characteristics between brake disk and pad are influenced by the disk mass. At a high disk mass, the friction stability was the lower value as a result of the lack of tribofilm formation at the disk surface. Wear rates of friction materials showed the higher value at a low disk mass and wear rates of 10 mm and 15 mm showed the similar level. Average friction coefficient was the lower value at the 10 mm disk thickness and range of variation of average friction coefficient was also the smaller value at the 10 mm disk thickness. However, there were no significant changes in the friction coefficients under any of test conditions. Surface roughness of a disk showed the highest value at the 5 mm disk and surface roughnesses of 10 mm and 15 mm showed the similar level. As a result, friction characteristics of disk mass influenced the friction stability, as well as the wear rate of friction pad and disk, but not the friction coefficient.

• Journal of Mechanical Science and Technology
• /
• 제20권8호
• /
• pp.1266-1274
• /
• 2006

A numerical study is performed to investigate the effect of inner surface roughness and micro-particles on adiabatic single phase frictional pressure drop in a perfect square micro channel. With the variation of particles sizes (0.1 to $1{\mu}m$) and occupied volume ratio (0.01 to 10%) by particles, the Eulerian multi-phase model is applied to a $100{\mu}m$ hydraulic diameter perfect square micro channel in laminar flow region. Frictional pressure loss is affected significantly by particle size than occupied volume ratio by particles. The particle properties like density and coefficient of restitution are investigated with various particle materials and the density of particle is found as an influential factor. Roughness effect on pressure drop in the micro channel is investigated with the consideration of roughness height, pitch, and distribution. Additionally, the combination effect by particles and surface roughness are simulated. The pressure loss in microchannel with 2.5% relative roughness surface can be increased more than 20% by the addition of $0.5{\mu}m$ diameter particles.

• 한국재료학회지
• /
• 제16권12호
• /
• pp.766-770
• /
• 2006

The frictional behavior of oxide films on top of the plasma nitrocarburized compound layers was investigated in terms of post-oxidation treatment temperatures. The post-oxidation treatment at both temperatures($400^{\circ}C,\;500^{\circ}C$) produced magnetite($Fe_3O_4$) films which led to a significant enhancement in corrosion resistance. However, this process did not result in any improvement in frictional behavior of the nitrocarburized surface. The wear mechanisms were governed predominantly by the abrasive action of the slider on the surface irrespective of the counterface material(SiC and Bearing steel). When the specimen was sliding against a SiC counterface, the oxide films were destroyed during the early stage of the sliding process and the wear debris of the oxide film at the sliding track had a great influence on the friction coefficient. On the other hand, when sliding against a bearing steel counterface, the slider was mainly worn out due to the much higher hardness of the surface hardened layer. The fluctuation of the friction coefficient of $400^{\circ}C$-oxidized/ nitrocarburized specimen is much severer than that of $500^{\circ}C$ specimen, due to the less amount of wear debris.

• 대한기계학회논문집A
• /
• 제28권12호
• /
• pp.1906-1913
• /
• 2004

A new method has been proposed for the calibration of frictional forces in atomic force microscopy. Angle conversion factor is defined using the relationship between torsional angle and frictional signal. Once the factor is obtained from a cantilever, it can be applied to other cantilevers without additional experiments. Moment balance equations on the flat surface and top edge of a commercial step grating are used to obtain angle conversion factor. Proposed method is verified through another step grating test and frictional behavior of Mica.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.846-851
• /
• 2004

A new method has been proposed for the calibration of frictional forces in atomic force microscopy. Angle conversion factor is defined using the relationship between torsional angle and frictional signal. Once the factor is obtained from a cantilever, it can be applied to other cantilevers without additional experiments. Moment balance equations on the flat surface and top edge of a commercial step grating are used to obtain angle conversion factor. Proposed method is verified through another step grating test and frictional behavior of Mica.

• Elastomers and Composites
• /
• 제39권1호
• /
• pp.12-22
• /
• 2004

라디오 주파수(13.56 MHz) 무전극 종형 플라즈마 반응기를 이용하여 천연고무 가교체의 표면을 클로로디플루오로메탄으로 처리하였다. FT-적외선 분광분석으로 표면개질 정도를 정성적으로 조사하였다. 플라즈마 처리표면의 마찰힘은 플라즈마 처리시간 증가에 따라 감소하였다. 고무표면에 에틸렌글리콜과 물을 떨어뜨려 접촉각을 측정한 결과 플라즈마 처리에 따라 감소하는 것으로 미루어 플라즈마 개질에 따라 표면극성이 증가하는 것을 확인하였다. 유리판 표면을 동일조건으로 플라즈마 처리한 경우는 극성의 감소만이 확인되었다. 표면자유에너지의 London 비극성 및 극성요소를 계산하는데 있어서 기하평균법과 조화평균법이 유용한 것으로 확인되었다. 평균방법에 관계없이 플라즈마 처리시간이 증가함에 따라 표면자유에너지는 증가하였다 그러나 조화평균법으로 계산된 자유에너지가 기하평균법으로 계산된 값에 비해 상대적으로 높았다. 플라즈마 표면개질은 마찰의 계면, 히스테리시스, 점성요소들에 영향을 미침으로써 마찰계수를 변화시키는 것으로 나타났다.

• 터널과지하공간
• /
• 제26권2호
• /
• pp.68-86
• /
• 2016

암반 구조물의 안정성을 분석하기 위해서는 암반 내 존재하는 불연속면의 전단거동 특성을 파악하는 것이 필수적이다. 특히 심부 지하에서의 암석 불연속면 마찰 거동 특성은 역학적, 수리적, 열적 및 화학적 조건과 각각의 조건들의 상호작용에 의해 영향을 받게 된다. 본 연구에서는 다양한 열-수리-역학적 조건에서 불연속면의 전단 거동 특성을 파악하기 위해 매끈한 화강암 불연속면 시험편과 거칠기를 포함한 유사암석 불연속면 시험편을 대상으로 삼축압축장비를 이용한 전단실험을 수행하였다. Coulomb의 전단강도 예측식을 이용하여 실험결과를 분석한 바 화강암 시험편의 경우 실험 조건의 변화에 따라 마찰 거동에 큰 변화를 보이지 않았으나 유사암석 시험편의 경우 응력 수준에 따라 변화를 보였다. 실험 조건의 변화에 따른 강성 및 팽창각의 변화를 분석한 결과 온도 및 수압 조건의 변화에 따라서 크게 변화하지 않음을 알 수 있었다.

• 한국재료학회지
• /
• 제25권1호
• /
• pp.21-26
• /
• 2015

CMP(Chemical Mechanical Polishing) Processes have been used to improve the planarization of the wafers in the semiconductor manufacturing industry. Polishing performance of CMP Process is determined by the chemical reaction of the liquid sol containing abrasive, pressure of the head portion and rotational speed of the polishing pad. However, frictional heat generated during the CMP process causes agglomeration of the particles and the liquidity degradation, resulting in a non-uniform of surface roughness and surface scratch. To overcome this chronic problem, herein, we introduced NaCl salt as an additive into silica sol for elimination the generation of frictional heat. The added NaCl reduced the zata potential of silica sol and increased the contact surface of silica particles onto the sapphire wafer, resulting in increase of the removal rate up to 17 %. Additionally, it seems that the silica particles adsorbed on the polishing pad decreased the contact area between the sapphire water and polishing pad, which suppressed the generation of frictional heat.

• Tribology and Lubricants
• /
• 제38권6호
• /
• pp.235-240
• /
• 2022

Atomically-thin 2D nanomaterials can be easily deformed and have surface corrugations which can influence the frictional characteristics of the 2D nanomaterials. Chemical vapor deposition (CVD) graphene can be grown in a wafer scale, which is suitable as a large-area surface coating film. The CVD growth involves cooling process to room temperature, and the thermal expansion coefficients mismatch between graphene and the metallic substrate induces a compressive strain in graphene, resulting in the surface corrugations such as wrinkles and atomic ripples. Such corrugations can induce the friction anisotropy of graphene, and therefore, accurate imaging of the surface corrugation is significant for better understanding about the friction anisotropy of CVD graphene. In this work, the combinatorial analysis using friction force microscopy (FFM) and transverse shear microscopy (TSM) was implemented to unveil the friction anisotropy of CVD bi-layer graphene. The periodic friction anisotropy of the wrinkles was measured following a sinusoidal curve depending on the angles between the wrinkles and the scanning tip, and the two domains were observed to have the different friction signals due to the different directions of the atomic ripples, which was confirmed by the high-resolution FFM and TSM imaging. In addition, we revealed that the atomic ripples can be easily suppressed by ironing the surface during AFM scans with an appropriate normal force. This work demonstrates that the friction anisotropy of CVD bilayer graphene is well-correlated with the corrugated structures and the local friction anisotropy induced by the atomic ripples can be controllably removed by simple AFM scans.