• Journal of Mechanical Science and Technology
• /
• 제18권10호
• /
• pp.1755-1762
• /
• 2004

Friction phenomenon can be described as two parts, which are the pre-sliding and sliding regions. In the motion of the sliding region, the friction force depends on the velocity of the system and consists of the Coulomb, stick-slip, Streibeck effect and viscous frictions. The friction force in the pre-sliding region, which occurs before the breakaway, depends on the position of the system. In the case of the motion of the friction in the sliding region, the LuGre model describes well the friction phenomenon and is used widely to identify the friction model, but the motion of the friction in the pre-sliding such as hysteresis phenomenon cannot be expressed well. In this paper, a modified friction model for the motion of the friction in the pre-sliding region is suggested which can consider the hysteresis phenomenon as the Preisach model. In order to show the effectiveness of the proposed friction model, the sliding mode controller (SMC) with hysteresis friction compensator is synthesized for a ball-screw servo system.

• 한국수소및신에너지학회논문집
• /
• 제26권6호
• /
• pp.659-665
• /
• 2015

In this study, an experimental investigation is performed for evaluation of a liquid pool spreading model with continuous release. The model considered in this study was developed based on a concept which means that the liquid pool spreading is governed by a balance between an inertia force from gravity and a frictional force from friction with the ground under the whole base of the liquid pool. For evaluation of the model, experimental study is performed. Experimental apparatus is setup for measuring release rate, spreading velocity, and evaporation rate from a liquid pool. The experimental results are compared with results from the model. By applying release and evaporation rates obtained from experiments to solving the model, liquid pool radius variation according to time can be obtained. For evaluation of an effect of friction force in the spreading model, results obtained from the models with and without the friction force are compared with those obtained from the experiments. As a result, it is shown that there exists a large deviation between the results obtained from the model without the friction force and the experimental results. On the other hand, the tendency of liquid pool radius variation according to time is similar between the results obtained from the model without the friction force and the experimental results.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.422-422
• /
• 2000

Parallel manipulators have been used to a variety of applications, including the motion simulators and mechanism for precise machining. A Stewart-Gough type parallel manipulator is composed of six linear joints which have wider contact areas than revolute ones, so linear joints are more affected by frictional force. First, the reference trajectories are computed from the model of the parallel manipulator assuming that it is subject to only the gravitational force and no friction exists. In the actual operation where friction exists, the control inputs, which correspond to the friction forces, are obtained by forcing the actual joint variables to follow these trojectories by proper control. It is shown that control performance can be improved when the friction compensation based on this information is added to the controller for position control of the moving plate of a parallel manipulator.

• 한국정밀공학회지
• /
• 제18권11호
• /
• pp.67-73
• /
• 2001

This paper aims at developing a torque model for the high-speed tapping with small-diameter taps. As recent industries such as automobile and information technology grows, taps smaller than 5mm in diameter are needed much more. In that occasion, the friction force between a tap surface and a workpiece plays much more important role in the tapping torque than in he larger tapping. Tapping mechanism was analysed based on the tap geometry. It has two steps : one is a forward cutting composed of the chamfered threading and full threading and the other is the backward cutting. The torque by the cutting force in the chamfered threading is calculated using the cutting area and the specific cutting force while the torque by the friction force, which is rather dominant than the cutting force both in the full threading and in the backward cutting, is calculated using the normal force on the threads and the friction coefficient. The experiment has shown that the results by the proposed torque model fit quite well with the acutal measurements within the error of 10%.

• Smart Structures and Systems
• /
• 제6권8호
• /
• pp.953-974
• /
• 2010

The performance of variable dampers for seismic protection of the benchmark highway bridge (phase I) under six real earthquake ground motions is presented. A simplified lumped mass finite-element model of the 91/5 highway bridge in Southern California is used for the investigation. A variable damper, developed from magnetorheological (MR) damper is used as a semi-active control device and its effectiveness with friction force schemes is investigated. A velocity-dependent damping model of variable damper is used. The effects of friction damping of the variable damper on the seismic response of the bridge are examined by taking different values of friction force, step-coefficient and transitional velocity of the damper. The seismic responses with variable dampers are compared with the corresponding uncontrolled case, and controlled by alternate sample control strategies. The results of investigation clearly indicate that the base shear, base moment and mid-span displacement are substantially reduced. In particular, the reduction in the bearing displacement is quite significant. The friction and the two-step friction force schemes of variable damper are found to be quite effective in reducing the peak response quantities of the bridge to a level similar to or better than that of the sample passive, semi-active and active controllers.

• 한국자동차공학회논문집
• /
• 제21권1호
• /
• pp.78-85
• /
• 2013

This paper presents the sliding mode control methods for anti-lock brake system (ABS) with the friction force observer. Using a simplified quarter car model, the sliding mode controller for ABS is designed to track the desired wheel slip ratio. Here, new method to find the desired wheel slip ratio which produces the maximum friction force between road and tire is suggested. The desired wheel slip ratio is varying according road and tire conditions to produce maximum friction force. In order to find optimum desired wheel slip ratio, the sliding mode observer for friction force is used. The proposed sliding mode controller with observer is evaluated in simulation, and the control design is shown to have high performance on roads with constant and varying adhesion coefficients.

• 한국자동차공학회논문집
• /
• 제16권4호
• /
• pp.103-109
• /
• 2008

Semi-spherical CVT(SS-CVT) is one of friction drives, which transmits power via the friction force between a spherical shaped variator and output disks. The variator varies the speed ratio of SS-CVT continuously as well as transmits input power into the output shaft. Therefore two friction forces are normally applied on the variator; one is the longitudinal friction force for power transmission and the other is the lateral for shifting. In order to investigate the dynamic behavior of SS-CVT, we introduced a numerical model of 2-dimensional friction force using a function of slip ratio and slip angle. And a dynamic model, which describes the shifting mechanism of SS-CVT, is developed through 3-dimensional vector analysis. Finally we presented numerical results of the shift characteristics focused on the transient behavior of the variator's slip ratio and slip angle. The numerical results also show the typical CVT shifting characteristics of SS-CVT and stable shifting behaviors of the variator.

• 한국정밀공학회지
• /
• 제32권5호
• /
• pp.423-429
• /
• 2015

Linear motion (LM) ball guides have good accuracy and high efficiency. They are widely applied for precision machinery such as machine tools, semiconductor fabrication machines and robots. However, friction force incurs heat between the balls and grooves. Thermal expansion due to the heat deteriorates stiffness and accuracy of the LM ball guides. For accurate estimation of stiffness and accuracy during the linear motion, friction models of LM ball guides are required. To formulate accurate frictional models of LM ball guides according to load and preload conditions, rolling and viscous frictional analyses have been performed in this paper. Contact loads between balls and grooves are derived from Hertzian contact analysis. Contact angle variation is incorporated for the precision modeling. Viscous friction model is formulated from the shear stress of lubricant and the contact area between balls and grooves. Experiments confirm validity of the developed friction model for various external load and feedrate conditions.

• 산업기술연구
• /
• 제24권B호
• /
• pp.207-214
• /
• 2004

An active stick which supplies force feedback to the operator is developed in this study. A mathematical model of the active stick is derived, and compared with the experimental result. It turns out that the frictional torque due to the mechanical contacts of several parts of the stick is one of the major barriers to achieve high precision operation of the stick. The frictional effect of the stick is cancelled out by using a friction observer. The efficacy of the friction observer is verified through the numerical simulation. Because of the observer dynamics, there are some limitations in exact recovering the static friction and Stribeck effect. However, the friction observer follows the real friction on the average. It's anticipated that the application of the friction observer to the closed loop control of the active stick improves the performance of the displacement versus force characteristics, which will be proved experimentally in the further study.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.27-30
• /
• 2007

In order to measure the friction coefficient used in sheet metal forming analysis, a friction tester was manufactured and friction tests were performed in various forming conditions. Based on the friction coefficients measured, a mathematical friction model was constructed in terms of lubricant viscosity, blank holding force, punch velocity and sheet roughness. In addition, the effect of the number of forming parameters in the calculation of friction coefficient on the accuracy of sheet metal forming analysis was investigated by comparing the punch loads obtained from the FEM simulation, in which the friction coefficients were determined by a few parameters with the experimental measurement.