• Particle and aerosol research
• /
• v.9 no.4
• /
• pp.271-277
• /
• 2013

This article reports the drag reduction phenomenon of aqueous suspensions containing carbon nanotubes (CNTs) flowing through horizontal tubes. Stable nanofluids were prepared by using a surfactant. It is found that the drag forces of CNT nanofluids were reduced at specific flow conditions compared to the base fluid. It is found that the friction factor of CNT nanofluids was reduced up to approximately 30 % by using CNT nanofluids. Increased kinematic viscosities of CNT nanofluids are suggested to the key factors that cause the drag reduction phenomenon. In addition, transition from laminar to turbulent flow is observed to be delayed when CNT nanofluids flow in a horizontal tube, meaning that drag reduction occurs at higher flow rates, that is, at higher Reynolds numbers.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.25 no.6
• /
• pp.795-801
• /
• 2019

The aim of this study was to investigate the possibility of the skin-friction reduction by vortex control. A vortical system such as a horseshoe vortex, a hairpin vortex, and a wake region was induced around a hemisphere attached on a Perspex flat plate in the circulating water channel. Hairpin vortices were developed from the wake region and horseshoe vortices were formed by an adverse pressure gradient in front of the hemisphere. The horseshoe vortices located on the flank of the hemisphere induced a high momentum flow in the wake region by the direction of their vorticity. This process increased the frequency of the hairpin vortices as well as the frictional drag on the surface of the wake region. To reduce the skin-friction drag, suction control in front of the hemisphere was applied through a hole. Flow visualization was performed to optimize the free-stream velocity, size of the hemisphere, and size of the suction hole. Once the wall suction control mitigated the strength of the horseshoe vortex, the energy supplied to the wake region was reduced, causing the frequency of the hairpin vortex generation to decrease by 36.4 %. In addition, the change in the skin-friction drag, which was measured with a dynamometer connected to a plate in the wake region, also decreased by 2.3 %.

• KSTLE International Journal
• /
• v.2 no.2
• /
• pp.150-153
• /
• 2001

The effects of humidity on friction performance of automotive brake materials were studied using a pad-on-disk type friction tester. Three different friction materials based on a simple formulation were investigated by changing the solid lubricant graphite, MoS$_2$, and Sb$_2$S$_3$. Friction materials without solid lubricants were also examined to study the effect of other ingredients in the matrix on humidity. The friction material containing graphite was strongly affected by the humidity showing lower friction coefficient at high humidity level than other conditions. On the other hand, the friction material containing MoS$_2$exhibited higher friction coefficient at initial stage under high humidity level. The friction material without solid lubricant or with Sb$_2$S$_3$ was not affected by humidity conditions. However, the friction material containing barite showed strong speed dependence.

• Tribology and Lubricants
• /
• v.13 no.3
• /
• pp.10-19
• /
• 1997

Frictional characteristics of two different types of automotive friction materials were studied. They were non-asbestos organic and semi-metallic friction materials. The two friction materials were tested using an inertial brake dynamometer to investigate friction stability, rooster tailing phenomena, temperature change during drags and stops. Results show that the level of the friction force is strong functions of time, temperature, and speed regardless of the type of friction materials. In particular, rooster tailing effects are pronounced in the case of semi-metallic friction materials compared to non-asbestos organic friction materials. The phenomena appear strongly dependent on raw materials contained in the friction materials.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1999.06a
• /
• pp.92-100
• /
• 1999

Friction characteristics of automotive friction materials according to the types of phenolic resin were investigated by using a pad-on-disk type friction tester. Four different simplified friction materials bound with Bakelite$^{TM}$ and Xylok$^{TM}$ phenolic resin were studied in this work. Two different modes of drag test(constant initial temperature test and constant interval test) were employed to analyze the effects of the binders on friction characteristics. Friction materials containing modified Xylok$^{TM}$ resin showed good heat resistance and friction stability. The results also showed that aramid fiber played important roles in improving friction stability and weard wear

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.10a
• /
• pp.323-329
• /
• 1998

The effect of humidity on friction characteristics of friction materials were studied using a pad-on-disk type friction tester. Three different friction materials containing simplified ingredients were investigated by changing the solid lubricant, graphite, MoS$_2$, and $Sb_2S_3$. A friction material without solid lubricant was also examined to study the effect of ingredients in the matrix on humidity. Friction material containing graphite showed lower friction coefficient at high humidity level than other conditions, however, friction material containing MoS$_2$ indicated higher friction coefficient at initial stage under high humidity level. Friction materials without solid lubricant and with $Sb_2S_3$ were little affected by humidity conditions.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1999.06a
• /
• pp.255-264
• /
• 1999

Friction characteristics of automotive friction materials containing different metallic fibers rubbing against Al-MMC and cast iron disk specimens have been studied. Friction materials containing aluminum, copper or low steel carbon fiber were tested. Friction tests were composed of three different phases to investigate the effect of temperature, pressure, speed, and drag time. The results showed that the friction material containing Al fibers has lower friction force and wear amount than the others with Cu or Steel fiber. On the other hand, the wear of friction material was severe in the case of using Al-MMC rotors. These results showed that the thermal decomposition of solid lubricants (and organic components), formation of transfer layer, and SiC particles in the AI-MMC rotor play crucial roles in determining the friction characteristics.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.7
• /
• pp.489-495
• /
• 2020

An accelerometer-based system was designed and constructed for drag measurement in a shock tunnel. Drag coefficient of a conical model was measured under a Mach 6 flow condition. A simple and intuitive calibration method was presented to compensate for the friction force of the drag measurement system, and the results of the measurement were compared with computational fluid dynamics in which the simple conical model was analyzed. The influence of drag measurement interference by supports of various shapes was identified and the design was presented to minimize. The drag coefficient measurement using the modified support showed that the error of the drag coefficient by the support was decreased.

• Journal of Advanced Marine Engineering and Technology
• /
• v.21 no.2
• /
• pp.126-135
• /
• 1997

Drag reduction in polymer solutions is the phenomenon where by extremely dilute solutions of high molecular weight polymers exhibit frictional resistance to flow much lower than the pure solvent. This effect, largely unexplained as yet, has attracted the attention of polymer scientists and fluid flow specialists. Although applications are beginning to appear, the principle interest to data has been in attempting to relate the effect to the fluid mechanics of turbulent flow. Drag reduction in two phase flow can be applied to the transport of crude oil, phase change system such as chemical reactor, and pool and boiling flow. But the research on drag reduction in two phase flow is not intensively investigated. Therefore, experimental investigations have been carried out to analyze the drag reduction produced by polymer addition in the single phase and two phase flow system. The objectives of the proposed investigation are primarily in identifying and developing high performance polymer additives for fluid transportations with the benefits of turbulent drag. Also we want to is to evaluate the drag reduction in horizontal flow by measuring pressure drop and mean velocity. Experimental results show higher drag reduction using co - polymer(A611P) then using polyacrylamide (PAAM) and faster degradation using PAAM than using A611P under the same superficial velocity.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.10a
• /
• pp.330-336
• /
• 1998

The friction and wear characteristics of automotive friction materials reinforced with carbon fibers were studied using a direct drive brake dynamometer. Two types of model friction materials, a low-metallic and an NAO type, were prepared and each of the materials was modified by substituting 5 vol% of carbon fibers with other reinforcing fiber used in the model formulations. Drag tests were carried out to investigate the friction properties of these materials at various braking conditions. Results showed that the modified friction materials were improved in the friction stability and the wear resistance.