• 지질공학
• /
• 제31권1호
• /
• pp.83-101
• /
• 2021

고밀도 폴리 우레탄 공법은 주입 물질의 순간 팽창압을 이용하여 연약지반의 불안정한 지반의 안정화를 위해 적용되며 내구성이 매우 탁월한 친환경 공법이다. 순간 팽창압에 의해 연약지반 보강 및 복원, 차수공사가 가능하다. 본 주입공법의 경우 작업시간이 매우 짧고 신속하여 열악한 환경에서도 타 공법보다 접급성과 작업성이 매우 탁월하다. 따라서 본 연구에서는 고밀도 폴리 우레탄이 지반 내에서 작용하는 물리·역학적 특성을 검증하고자 하였다. 먼저, 주입재료의 강도정수 및 물성값을 확인하기 위하여 일축압축강도시험, 직접전단시험, 토압시험 등을 수행하였고 환경적인 문제에 대한 부분을 확인하고자 투수시험 및 토양환경안정성 시험을 수행하였다. 실험결과, 조밀한 사질토와 단단한 점성토를 대상으로 비교하였을 때, 내부마찰각은 약 2배, 점착력은 약 2.5~3.5배 이상 높은 것으로 확인되었고, 투수계수 또한 1.0 × 10-5의 범위 이내를 만족하며, 기존 그라우팅 공법과 비교하였을 때 현저히 낮은 투수계수를 확인할 수 있었다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 추계학술대회 논문집
• /
• pp.62-65
• /
• 2009

There have been strong demands for micro size screw with high precision due to miniaturization and integration trends for electronic products such as Hard Disk Drives. The thread rolling process for screw manufacturing are lower unit cost, reduced material utilization, and superior mechanical properties compared to the machining process. But little work has been done on the thread rolling of micro size screw. In this paper, we investigate thread rolling process using Finite Element Analysis (FEA) and parameter study for screw manufacturing. And we also carried out compression tests to obtain the material property and to implement into the FE tool for the numerical simulation. In case that parameter of relative position oldies is half length of pitch for maintaining the continuous thread profiles, we found that shear friction factor was 0.9 during the thread rolling process using FEA. We are trying to develop the thread rolling process using the FE-simulation to manufacture screws which have been commonly produced from the industrial level fabrication at present.

• Tribology and Lubricants
• /
• 제36권3호
• /
• pp.147-152
• /
• 2020

This paper is within the framework of an adhered complete contact problem wherein the contact between a half plane and sharp edged indenter, both of which are elastic in character, is constituted. The eigensolutions of the contact shear and normal stresses, σ_rq and σ_q, respectively, are evaluated via asymptotic analysis. The ratio of σ_rq/σ_qq is investigated and compared with the coefficient of friction, μ, of the contact surface to observe the propensity to slip on the contact surface. Interestingly, there exists a region of |σ_rθ/σ_θθ| ≥ |μ|. Thus, slipping can occur, although the problem is solved under the condition of an adhered contact without slipping. Given that a tribological failure potentially occurs at the slipping region, it is important to determine the size of the slipping region. This aspect is also factored in the paper. A simple example of the adhered contact between two elastically dissimilar squares is considered. Finite element analysis is used to evaluate generalized stress intensity factors. Furthermore, it is repeatedly observed that slipping occurs on the contact surface although the size of it is extremely small compared with that of the contacting squares. Therefore, as a contribution to the field of contact mechanics, this problem must be further explained logically.

• Earthquakes and Structures
• /
• 제12권2호
• /
• pp.251-262
• /
• 2017

The present research intends to study the effects of the seismic soil-foundation-structure interaction (SFSI) on the dynamic response of various buildings. Two methods including direct and Cone model were studied through 3D finite element method using ABAQUS software. Cone model as an approximate method to consider the SFSI phenomenon was developed and evaluated for both high and low rise buildings. Effect of soil nonlinearity, foundation rigidity and embedment as well as friction coefficient between soil-foundation interfaces during seismic excitation are investigated. Validity and performance of both approaches are evaluated as reference graphs for Cone model and infinite boundary condition, soil nonlinearity and amplification factor for direct method. A series of calculations by DeepSoil for inverse earthquake record modification was conducted. A comparison of the two methods was carried out by root-mean-square-deviation (RMSD) tool for maximum lateral displacement and story shear forces which verifies that Cone model results have good agreement with direct method. It was concluded that Cone method is a convenient, fast and rather accurate method as an approximate way to count for soil media.

• 대한기계학회논문집A
• /
• 제27권12호
• /
• pp.2019-2027
• /
• 2003

Pitting wear is a dominant from of polyethylene surface damage in total knee replacements, and may originate from surface cracks that propagate under repeated tribological contact. In this study, stress intensity factors, K$\_$I/and $_{4}$, were calculated for a surface crack in a polyethylene-CoCr-bone system under the rolling and/or sliding contact pressures. Crack length and load location were considered in determination of probable crack propagation mechanisms and fracture modes. Positive K$\_$I/ values were obtained for shorter cracks in rolling contact and for all crack lengths when the sliding load was apart from the crack. $_{4}$ was the greatest when the load was directly adjacent to the crack (g/a=${\pm}$1). Sliding friction caused a substantial increase of both K$\_$I/$\^$max/ and $_{4}$$\^$max/. The effective Mode I stress intensity factors, K$\_$eff/, were the greatest at g/a=${\pm}$1, showing the significance of high shear stresses generated by loads adjacent to surface cracks. Such behavior of K$\_$eff/ suggests mechanisms for surface pitting by which surface cracks may propagate along their original plane under repeated rolling or sliding contact.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1222-1227
• /
• 2003

Pitting wear is a dominant form of polyethylene surface damage in total knee replacements, and may originate from surface cracks that propagate under repeated tribological contact. In this study, stress intensity factors, $K_{I}$ and $K_{II}$, were calculated for a surface crack in a polyethylene - CoCr - bone system under the rolling and/or sliding contact pressures. Crack length and load location were considered in determination of probable crack propagation mechanisms and fracture modes. Positive $K_{I}$ values were obtained for shorter cracks in rolling contact and for all crack lengths when the sliding load was apart from the crack. $K_{II}$, was the greatest when the load was directly adjacent to the crack $(g/a={\pm}1)$. Sliding friction caused a substantial increase of both $K_{I}^{max}$ and $K_{II}^{max}$. The effective Mode I stress intensity factors, $K_{eff}$, were the greatest at $g/a={\pm}1$, showing the significance of high shear stresses generated by loads adjacent to surface cracks. Such behavior of $K_{eff}$ suggests mechanisms for surface pitting by which surface cracks may propagate along their original plane under repeated rolling or sliding contact.

• 한국정밀공학회지
• /
• 제25권4호
• /
• pp.61-68
• /
• 2008

Of the seven base units of the international system of units, only the kilogram is still defined in terms of a material artifact. One of the experimental approaches opening the way to a new definition of the kilogram is the watt balance To improve the performance of the NPL watt balance, we need to quantify and reduce hysteresis effects in the balance knives. In this paper, we discuss the mechanical characteristics of the knife edges used in the NPL watt balance. The hysteresis mechanism is analyzed using the finite element method. It is found that the cause of hysteresis is not normal stress but shear, and the deformation of the flat, rather than the knife, is an important factor in the hysteresis mechanism. The study presented here, using finite element analysis, suggests that parameters such as material property, tip radius and knife straightness can be more important than others, such as friction coefficient, tip angle, etc.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 추계학술대회 논문집
• /
• pp.192-197
• /
• 2002

In this study, examined the cutting characteristics of alumuminum alloy AC8A-T6 that is used to present car piston materials. And in been holding materials machining empirically escape as result that experiment comparison changing the cutting speed and feed on various condition to choose efficient machining condition. The following results can be summarized from this research. 1. As the cutting speed decreased, principal cutting force and thrust cutting force is increased, and reason that cutting force interacts greatly in the low cutting speed is thought by result by BUE's stabilization. 2. The feed speed and cutting speed increase, friction factor is decrescent and the cause appeared the thrust cutting force is fallen than cutting force relatively because chip flow according to increase of the feed rate is constraint. 3. Though specific cutting resistance grows cutting area and the feed rate are few, the cause was expose that shear angle decreases by rake face of tool gets into negative angle remarkably as wear of a cutting tool or defect part of workpiece is cut. 4. Cutting speed do greatly depth of cut is slow, surface roughness examined closely through an experiment that becomes bad, and know that it can get good surface that process cutting speed because do feed rate by 0.1mm/rev low more than 250m/min to get good surface roughness can.

• 한국지반환경공학회 논문집
• /
• 제11권1호
• /
• pp.13-18
• /
• 2010

암반구조물의 안정해석을 위해서는 암반의 특성을 연구하여 설계에 요구되는 매개변수를 합리적으로 결정해야한다. 본 논문에서는 여수, 광주, 양산, 부산, 대전 등의 안산암, 응회암지역을 대상으로 공내재하시험과 일축 및 삼축압축시험을 수행하고 기존에 제안된 추정식을 비교분석하였다. Nicholson & Bieniawski가 제안한 감쇠계수를 이용하여 변형계수를 추정한 결과 RMR이 60미만인 경우에는 감쇠계수를 고려한 공내재하시험결과를 이용하는 것을 제안하며, RMR값이 60 이상인 경우에 대해서는 김교원에 의해 제안된 식이 가장 근접하는 것으로 나타났다. 그리고 RMR과 점착력, 그리고 내부마찰각을 비교한 결과, 점착력과 내부마찰각 모두 Tsuchiya의 제안식이 가장 일치하는 것으로 나타났다. 본 연구에서 암반 변형계수와 RMR의 관계를 비교분석하고 RMR값을 이용한 전단강도정수 산정식을 제안하였는 바 변형계수와 전단강도정수는 RMR지수 산정요소에 포함되지 않아 여러 인자들에 의해 결과가 달라질 수 있으므로 국내 현장에 맞는 실용적인 추정식들이 제안되어져야 할 것으로 사료된다.

• 지질공학
• /
• 제11권1호
• /
• pp.1-11
• /
• 2001

우리나라 지질의 특성은 토층의 두께가 얇아서 보통 10m이상만 굴착해도 암반층이 나타나므로 대규모 지하굴착 공사시 암반층에서의 토압분포 산정방법이 절실하게 요구되고 있는 실정이다. 그러나, 암반층 암압산정시 기존의 경험식인 Terzaghi-Peck, Tschebotarioff식 등을 그대로 적용하는 것은 암반층의 점착력을 대부분 무시하게 되므로 실제 강도를 과소 평가하게 된다. 따라서 암반에서의 절리경사각, 절리면 전단강도, 지반 상재하중등을 고려한 쐐기형 블럭(Wedge Block)의 수평활동력을 산정하는것이 실제 암반층 토류구조물에 작용하는 암압과 근접할 것으로 판단된다. 본 연구에서는 뒷채움 흙이 점착력을 갖는 흙인 경우 쐐기형상으로 파괴가 일어난다고 가정하여 Coulomb 토압이론을 확장하여 힘의 평형 조건을 이용해 Prakash-Saran(1963)이론과 절리면의 전단강도 결정공식 $\tau$=c+$\sigma$tan $\Phi$를 적용해서 암반층에 작용하는 암압을 산정하였다. 산정된 이론식을 이용하여 절리면 충전물의 상태 변화에 따른 절리면 전단 강도와 절리경사각을 바꿔가면서 해석해 본 결과, 암반층은 자체의 점착력과 내부마찰각이 크므로 절리방향과 경사각이 굴착면을 향해 어떻게 정해지느냐에 따라서 토압이 작용하기도 하고 작용하지 않을 수도 있다. 본 연구에서 산정된 이론식은 향후 절리면 전단강도 산정시 필요한 강도정수, 절리면의 방위와 상태, 과잉측압, 동적하중, 지진을 비롯한 많은 지반정수(Parameter)들을 보다 엄밀히 산정하고, 특히 암반층에 작용하는 지하수위 효과등을 고려하여, 실제 현장에서 계측된 많은 자료와의 분석을 통해 그 적용성이 검토되어야 할 것으로 판단된다.