• Korean Chemical Engineering Research
• /
• v.48 no.6
• /
• pp.784-790
• /
• 2010

VOCs such as acetone, benzene, toluene, ethylbenzene were adsorbed in a fixed-bed adsorber using zeolite synthesized from coal fly ash and 4 kinds of activated carbon at 101.3 kPa. The adsorber was operated batchwise with the charge of 5 g adsorbent to obtain the breakthrough curve of VOCs. Experiments were carried out at $40^{\circ}C$, nitrogen flow rate of $70cm^3/min$ and sparger temperature of $30^{\circ}C$. The deactivation model was tested for these curves by combining the adsorption of VOCs and the deactivation of adsorbent particles. The observed values of the adsorption rate constant and the deactivation rate constant were evaluated through analysis of the experimental breakthrough data using a nonlinear least square technique. The experimental breakthrough data were fitted very well to the deactivation model than the adsorption isotherm models in the literature. Also, adsorption capacities of adsorbents were obtained from the breakthrough curve to observe the correlation between adsorption capacity and the physical properties of VOCs.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.8
• /
• pp.566-573
• /
• 2012

This study examined the removal rate of heavy metals from synthetic control water using red mud and lime stone. Overall, the percent of absorption obtained in this study for the red mud treatment was 94.0% ($Pb^{2+}$), 67.1% ($As^{3+}$), 37.5% ($Cu^{2+}$), and 36.6% ($Cr^{6+}$), while that of lime stone was $Pb^{2+}$ (30.8%), $Cu^{2+}$ (16.5%), $Cr^{6+}$ (11.5%), and $As^{3+}$ (8.9%). The kinetic data presented that the slow course of adsorption follows the Pseudo first and second order models, the equilibriuim adsorption of $Cr^{6+}$ and $Pb^{2+}$ obeys Freundlich isotherm model, while the adsorption of $Cu^{2+}$ obeys only Langmuir model. The results also showed that adsorption rate slightly increased with increasing pH from 5 to 9. Interestingly, this trend is similar to results obtained as function of loading amount of red mud. Meanwhile, an unit adsorption rate was slightly decreased. For lime stone, it did not much change in adsorption as function of treatment amount. Consequently, it was concluded that the absorbents can be successfully used the removal of the heavy metals from the aqueous solutions.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.8
• /
• pp.663-672
• /
• 2009

In this studies, the adsorption test using Chlorella pyrenoidosa was conducted to examine the effect of Pb adsorption according to various immobilized methods such as Ca-alginate, K-carrageenan, and Polyacrylamide. From the results, the duration to need to reach adsorption equilibrium was delayed according to the immobilization. And, the higher adsorption capacity of immobilized Chlorella pyrenoidosa was represented in the higher concentration of Pb, the smaller amount of immobilizing agent, and the higher pH of solution. The maximum adsorption capacity of Pb was shown in the adsorption test using Chlorella pyrenoidosa immobilized with Ca-alginate even though it was sensitive pH. The adsorption results properly represented with Freundlich isotherm equations. And, pseudo second-order chemisorption kinetic rate equation was applicable to all the biosorption data over the entire time range. The FT-IR analysis showed that the mechanism involved in biosorption of Pb by Chlorella pyrenoidosa was mainly attributed to Pb binding of carbo-acid and amide group. Adsorbed Pb on immobilized Chlorella prenoidosa was easily desorbed in the higher concentration of desorbents(NTA, HCl, EDTA, $H_2SO_4,\;Na_2CO_3$). Among the several desorbents, NTA showed the maximum desoption capacities of Pb from Chlorella pyrenoidosa immobilized with Ca-alginate and K-carrageenan and EDTA was the most effective in Chlorella pyrenoidosa immobilized with polyacrylamide. The desoprtion efficiency in the optimum condition was 90.0, 83.0, and 80.0%, respectively.

• Korean Journal of Environmental Agriculture
• /
• v.7 no.2
• /
• pp.96-101
• /
• 1988

It is important to assess the effects of ionic strength and type of anions when studying the adsorption of heavy metals on zeolite because the background salt may complex with heavy metals and compete for adsorption sites. This experiment was carried out to determine the effect of ionic strength and anion species($Cl^-$, $SO^{2-}\;_4$, and $ClO^-\;_4$) on heavy metal adsorption. Heavy metal adsorption by zeolite from solutions in the range of 10 to 50ppm was studied in the presence of NaCl, $Na_2SO_4$ and $NaClO_4$, with different concentrations. The ionic strength ranged from 0.01 to 1.00. Adsorption of heavy metal cations could be described by the Freundlich isotherm equation. Increasing the ionic strength of equilibrium solutions, the amounts of heavy metal adsorbed on the zeolite surfaces decreased in all three of the anion systems. This fact could be attributed to the competition of background salt cation and the decrease in initial activity of heavy metal cations. In the presence of Cl anion, less adsorption resulted than in the presence of $SO_4$ or $ClO_4$ anions of the same ionic strength, indicating the presence of uncharged and negatively charged complexes of heavy metal with Cl ligands.

• Resources Recycling
• /
• v.13 no.4
• /
• pp.23-31
• /
• 2004

Basic studies have been conducted regarding the attempt of the utilization of waste Undaria pinnatifida as an adsorbent for the adsorption treatment of lead-containing wastewater. Undaria pinnatifida was found to be chiefly composed of hyo-carbonaceous compounds and have a fairly high specific surface area, which suggesting the possibility of its application as a Potential adsorbent. The electrokinetic Potential of Undaria pinnatifida particles was observed to be negatively highest at around pH 8 and the fact that its electrokinetic potentials are negative at the whole pH range supported it might be an efficient adsorbent especially for cationic adsorbates. Under the experimental conditions, $Pb^{2+}$ was found to mostly adsorb onto Undaria pinnatifida within a few minutes and reach the equilibrium in adsorption within ca. 30 minutes. The adsorption of $Pb^{2+}$ was exothermic and explained well by e Freundlich model. Acidic pretreatment of Undaria pinnatifida enhanced its adsorption capacity for $Pb^{2+}$ , however, the reverse was observed for alkaline pretreatment. The formation of organometallic complex between $Pb^{2+}$ and some functional groups on the surface of Undaria pinnatifida was considered to be one of the main drives for adsorption. Finally the adsorbability of$ Pb^{2+}$ was examined to be rather affected by several solution features such as the coexistence of other adsorbate, the variation of ionic strength, and the concentration of complexing agent.

• Journal of the Korean GEO-environmental Society
• /
• v.10 no.7
• /
• pp.25-32
• /
• 2009

The main objective of this study was to examine the removal properties of Cu from water by inflated vermiculites. The component of vermiculites was analyzed by XRF and the concentration of Copper ion was measured by UV-VIS. Serial batch Kinetic tests and batch sorption tests were conducted to determine the removal characteristics for Cu in aqueous solutions. The result shows that removal rate, $K_{obs}$, of Cu are 0.73, 1.52, and 1.71 for initial pH 3, pH 4, pH 5, respectively, and are 3.19, 1.90, and 0.73 for the initial concentration of $1mg\;L^{-1}$, $5mg\;L^{-1}$, $10mg\;L^{-1}$, respectively. It leads to the conclusion that the removal rates are inversely proportional to the initial Cu concentration and are increased proportionally to the initial pHs. Finally, Sorption data were correlated with both Langmuir and Freundlich isotherms. As a result, Langmuir and Freundlich models were well fitted to batch isotherm data with good values of the determination coefficient. but the determination coefficient value for the Freundlich model fit was slightly higher than that of Langmuir model (0.965 for the Freundlich model and 0.936 for the Langmuir model). Using the Langmuir model, the maximum sorption capacity ($Q_{max}$), Freundlich partition coefficient, and the numerical value of n wrer estimated as $1,250mg\;kg^{-1}$, $635.1L\;kg^{-1}$ and 1.69, respectively. These results show that the inflated vermiculites could be used as an excellent adsorbent for copper contained in various types of aqueous solutions.

• Journal of the Korean Chemical Society
• /
• v.66 no.2
• /
• pp.78-85
• /
• 2022

Natural white clay was treated with 6 M of H₂SO₄ and heated at 80℃ for 6 h under mechanical stirring and the resulting acid active clay was used as an adsorbent for the removal of Cs⁺ in water. The physicochemical changes of natural white clay and acid active clay were observed by X-ray Fluorescence Spectrometry (XRF), BET Surface Area Analyser and Energy Dispersive X-line Spectrometer (EDX). While activating natural white clay with acid, the part of Al₂O₃, CaO, MgO, SO₃ and Fe₂O₃ was dissolved firstly from the crystal lattice, which bring about the increase in the specific surface area and the pore volume as well as active sites. The specific surface area and the pore volume of acid active clay were roughly twice as high compared with natural white clay. The adsorption of Cs⁺ on acid active clay was increased rapidly within 1 min and reached equilibrium at 60 min. At 25 mg L^- of Cs⁺ concentration, 96.88% of adsorption capacity was accomplished by acid active clay. The adsorption data of Cs⁺ were fitted to the adsorption isotherm and kinetic models. It was found that Langmuir isotherm was described well to the adsorption behavior of Cs⁺ on acid active clay rather than Freundlich isotherm. For adsorption Cs⁺ on acid active clay, the Langmuir isotherm coefficients, Q, was found to be 10.52 mg g^-1. In acid active clay/water system, the pseudo-second-order kinetic model was more suitable for adsorption of Cs⁺ than the pseudo-first-order kinetic model owing to the higher correlation coefficient R² and the more proximity value of the experimental value q_e,exp and the calculated value q_e,cal. The overall results of study showed that acid active clay could be used as an efficient adsorbent for the removal of Cs⁺ from water.

• Environmental Engineering Research
• /
• v.25 no.1
• /
• pp.96-103
• /
• 2020

The aim of this study is to investigate the effect of five different combinations including: sand 70%, bentonite 30% (S₇₀B₃₀)- sand 80%, bentonite 20% (S₈₀B₂₀)- sand 80%, organophilic 20% (S₈₀M₂₀)- sand 60%, bentonite 20%, organophilic 20% (S₆₀B₃₀M₂₀) and sand 75% - bentonite 15% - organophilic 10% (S₇₅B₁₅M₁₀) on landfill linear structure in order to decrease phenol leaching. Hydraulic conductivity and adsorption behavior of the samples were investigated. The results demonstrated that the lowest hydraulic conductivity coefficient ($1.16{\times}10^{-11}{\frac{m}{s}}$) was obtained for S₇₀B₃₀. Furthermore, adding more than 20% of bentonite had no significant effect on reducing permeability. Moreover, Freundlich isotherm was introduced as the best model explaining adsorption behaviour due to its highest determination coefficient (0.945). The best samples for adsorption capacity of phenol and for both permeability and adsorption are S₈₀M₂₀ and S₆₀B₃₀M₂₀, respectively. Although the presence of bentonite was effective in reducing hydraulic conductivity, organic clay had no considerable impact on reducing permeability. Though, it's an exceptional role in adsorbing organic contaminants including phenol cannot be ignored. To meet all regulatory constraints, the optimal compound is made up of 10.2% of bentonite and 2.8% of organophilic clays with a minimized cost of 13.64 ($/ton).

• Resources Recycling
• /
• v.20 no.6
• /
• pp.28-36
• /
• 2011

The adsorption of nickel(Ni) from sulfuric acid solution was carried out by ion exchange method. A series of batch tests in synthetic solutions were carried out using Lewatit Monoplus TP 220 resin. The following experimental parameters, such as temperature, shaking rate, reaction time, pH, resin dosage and concentration of nickel ions etc. were investigated to establish the effective optimum conditions of nickel adsorption. The solution pH(2.0~5.0) and shaking rate had little effects on the adsorption of nickel and adsorption time of 72hours was required to reach equilibrium. The experimental results show a good agreement with Feundlich isotherm and pseudo-second order reaction. The adsorption behavior of Ni obtained from synthetic solution was compared with that of waste electroplating solution. Elution of nickel from loaded resin increased with increase in $H_2SO_4$ concentration.

• Journal of the Korean Chemical Society
• /
• v.54 no.3
• /
• pp.300-309
• /
• 2010

The ability of sodium-exchanged clay particles as an adsorbent for the removal of commercial dyes, Methylene blue (MB) and Malachite green oxalate (MG) from aqueous solutions has been investigated under various experimental conditions. The effect of the experimental parameters, such as pH solution, agitation time, adsorbate concentration and adsorbent dose were examined. Maximum adsorption of dyes, i.e. >90% has been achieved in aqueous solutions using 0.03 g of clay at a pH of 7 and 298 K for both dyes. The adsorption process was a fast and the equilibrium was obtained within the first 5 min. For the adsorption of both MB and MG dyes, the pseudo-second-order reaction kinetics provides the best correlation of the experimental data. The adsorption equilibrium results follow Langmuir and Dubini-Radushkevich (D-R) isotherms with high regression coefficients $R^2$ > 0.98. The mean free energies $E_a$ of adsorption from D-R model were 3.779 and 2.564 kj/mol for MB and MG respectively, which corresponds to a physisorption process.