• 한국항공우주학회지
• /
• 제37권7호
• /
• pp.642-652
• /
• 2009

항공기 주구조에 많은 부분은 겹침이음 형태의 조립구조이며 이러한 구조는 프레팅 손상으로 인해 단순피로에 비해 현저히 수명이 감소된다. 특히 노후 항공기의 경우 프레팅 피로균열은 감항안전을 저해하는 중요한 요인으로 최근 대두된 수명연장 문제와 관련해서도 손상허용성 평가에 프레팅 피로수명 예측이 필수적으로 요구되고 있다. 이러한 배경으로 본 연구에서는 볼트 체결력이 서로 다른 겹침이음 구조시편에 대하여 일련의 프레팅 피로시험을 수행하고 탄소성 접촉응력 유한요소해석 결과로부터 프레팅 파라미터를 구하고 균열발생 및 성장 수명예측 모델식과 최근 제안된 수정 모델식을 통하여 프레팅 피로수명을 예측하였다. 또한 시험결과와 비교분석함으로써 실제 항공기 겹침이음 구조에 프레팅 피로수명 예측 모델식의 적용 유효성을 고찰하였다.

• 한국공작기계학회논문집
• /
• 제14권3호
• /
• pp.103-109
• /
• 2005

Since fretting fatigue damage accumulation occurs over relatively small volumes, the role of the microstructure is quite significant in fretting fatigue analysis. The heterogeneity of discrete grains and their crystallographic orientation can be accounted for using continuum crystallographic cyclic plasticity models. Such a constitutive law used in parametric studies of contact conditions may ultimately result in more thorough understanding of realistic fretting fatigue processes. The primary focus of this study is to explore the influence of microstructure as well as the magnitude of the normal force and tangential force amplitude during the fretting fatigue process. Fretting maps representing cyclic plastic strain behaviors are also developed to shed light on the cyclic deformation mechanisms.

• 대한기계학회논문집A
• /
• 제35권9호
• /
• pp.983-989
• /
• 2011

본 연구에서는 경제요소법을 이용한 프레팅 마멸 예측을 위한 수치적 알고리즘을 개발하였다. 반무한체 해석을 통해 사각조각면위의 균일분포하중과 탄성변형량의 관계로부터 접촉 계면의 응력을 계산하였고 Archard wear 모델을 이용해 각 격자의 마멸 깊이를 계산하여 접촉면의 형상을 예측할 수 있는 알고리즘을 제시하였다. 본 연구의 정확성을 검증하기 위해 McColl 등의 연구와 비교하였고 개발된 알고리즘을 구접촉 모델에 확장하여 그 유용성을 확인하였다. 아울러 프레팅 해석의 효율적인 계산을 위해 한 step당 사이클 증가량인 step cycle이 해의 정확성에 미치는 영향을 검토하여 step cycle 설정의 중요성을 제시하였다.

• 한국정밀공학회지
• /
• 제24권4호
• /
• pp.123-130
• /
• 2007

Recently, a lot of work and interest have been devoted to the development of multiaxial fatigue parameters for fretting fatigue life prediction. In this study, the fretting fatigue lift and critical location ware estimated and evaluated through the multiaxial fatigue theories in a cylinder-on-flat contact configuration far Cr-Mo steel, SCM420, the material commonly is used in gears of the automobile and rollers of the conveyor. The strain-life curve was obtained from fatigue test for SCM420. The Fretting fatigue life and critical location were estimated through stress distributions, SWT-parameters and FS-parameters obtained from FEA. This paper showed possibility of applying multiaxial fatigue theories to fretting fatigue lift prediction comparing predicted life with experimental results.

• Tribology and Lubricants
• /
• 제21권1호
• /
• pp.33-38
• /
• 2005

Fretting is the oscillatory motion with very small amplitudes, which usually occurs between two solid surfaces in contact. Fretting wear is the removal of material from contacting surfaces through fretting action. Fretting wear of steam generator tubes in nuclear power plant becomes a serious problem in recent years. The materials for the tubes usually are Inconel 690 (I-690) and Inconel 600 (I-600). In this paper, fretting wear tests for I-690 and I-600 were performed under various applied loads in water at room temperature. Results showed that the fretting wear loss of I-690 and I-600 tubes was largely influenced by stick-slip. The fretting wear mechanisms were the abrasive wear in slip regime and the delamination wear in stick regime. Also, I-690 had somewhat better wear resistance than I-600.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.168-173
• /
• 2004

Fretting is a kind of surface degradation mechanism observed in mechanical components and structures. The fretting damage decrease in 50-70% of the plain fatigue strength. This may be observed in aircraft, automobile and nuclear power plant used in special environment and various loading conditions. In the present study, the characteristics of the fretting fatigue are investigated using the two aluminum alloy(Al2024-T3511 and Al7050-T7451). Through the experiment, it is found that the fretting fatigue strength of the Al7050-T7451 alloy decreased about 50% from the plain fatigue strength, while the fretting fatigue strength of the Al2024-T3511 alloy decreased about 45%. The tire track was widely observed in fracture surface area of oblique crack which was induced by contact pressure. These results can be the basic data to the structural integrity evaluation of aluminum alloy subjected to fretting damage.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.1467-1468
• /
• 2010

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2009년도 추계학술대회 논문집
• /
• pp.447-448
• /
• 2009

• 대한기계학회논문집A
• /
• 제33권10호
• /
• pp.1091-1098
• /
• 2009

In this paper, the procedure to estimate fatigue crack initiation life has been established by considering fretting wear and multiaxial stress states on the contact surface of press-fitted shafts. And a method to calculate the local friction coefficient during the running-in period of fretting wear process has been proposed. The predicted result of worn surface profile in the press-fitted shaft with non-linear local friction coefficient can avoid excessive wear depth estimation compared with that for the case of constant local friction coefficient. Furthermore, the predicted fatigue crack initiation lives based on Smith-Watson-Topper model considering the fretting wear are in good agreement with the experimental data. Consequently, the present method is valid not only for predicting worn surface profile, but also for assessing fatigue crack initiation lives considering the fretting wear during the running-in period in press fits.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 추계학술대회 논문집
• /
• pp.113-114
• /
• 2008