• Korean Journal of Metals and Materials
• /
• v.48 no.11
• /
• pp.1014-1020
• /
• 2010

In order to improve the purity on deposit in cobalt electrowining, a fundamental study using Pulse-Reverse Current (PRC) was carried out. Based on a sulfate solution, Cu, Ni, and Fe as impurities were added during cobalt electrowinning. There were four reverse waveforms and frequency conditions from 1 Hz to 10 kHz, and the purity of each condition was compared with the Direct Current (DC) purity. From the results, it was found that the anodic potential induced by reverse current affects selective dissolution of impurities. In this work, the case of the highest reverse peak current density ($I_r$) with a short reverse time ($t_r$) at 100 Hz showed a higher purity than that of the DC. This PRC condition also showed only a 4% low current efficiency comparable to the DC. We concluded that an optimized PRC for cobalt electrowinning could improve the purity with little loss of current efficiency.

• Journal of Power Electronics
• /
• v.19 no.1
• /
• pp.146-157
• /
• 2019

The inverter is an essential part of permanent magnet synchronous motor (PMSM) drive systems. The performance of an inverter is greatly influenced by its modulation strategy. Using a proper management of modulation strategies can guarantee high performance from a PMSM under various speed conditions. Switching between modulations is a pivotal technique that determines the performance of a PMSM. Most works on hybrid methods focus on two-level induction motors drive systems. In this paper, in order to improve the performance of PMSMs under various speed conditions, a hybrid method of a pulse width modulation (PWM) control scheme based on a neutral-point-clamped (NPC) three level topology was proposed. This hybrid PWM modulation comprised space vector PWM (SVPWM) and selective harmonic elimination PWM (SHEPWM). Under low speed conditions, the SVPWM is employed to cause the PMSM to start smoothly, and to obtain a rapid response from the control system. Under high speed conditions, the SHEPWM is employed to reduce the switching frequency and to eliminate particular current harmonics. Moreover, the harmonic characteristics of different modulations are analyzed to obtain a smooth transition between the SHEPWM and the SVPWM. Experimental and simulation results indicated the effectiveness of the proposed control method.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.15 no.6
• /
• pp.2240-2254
• /
• 2021

We investigate the channel allocation problem in an ultra-dense device-to-device (D2D) enabled cellular network in underlaying mode where multiple D2D users are forced to share the same channel. Two kinds of low complexity solutions, which just require partial channel state information (CSI) exchange, are devised to resolve the combinatorial optimization problem with the quality of service (QoS) guaranteeing. We begin by sorting the cellular users equipment (CUEs) links in sequence in a matric of interference tolerance for ensuring the SINR requirement. Moreover, the interference quota of CUEs is regarded as one kind of communication resource. Multiple D2D candidates compete for the interference quota to establish spectrum sharing links. Then base station calculates the occupation of interference quota by D2D users with partial CSI such as the interference channel gain of D2D users and the channel gain of D2D themselves, and carries out the channel allocation by setting different access priorities distribution. In this paper, we proposed two novel fast matching algorithms utilize partial information rather than global CSI exchanging, which reduce the computation complexity. Numerical results reveal that, our proposed algorithms achieve outstanding performance than the contrast algorithms including Hungarian algorithm in terms of throughput, fairness and access rate. Specifically, the performance of our proposed channel allocation algorithm is more superior in ultra-dense D2D scenarios.

• International Journal of Knowledge Content Development & Technology
• /
• v.14 no.1
• /
• pp.33-52
• /
• 2024

This study examined the virtual methods of service delivery being deployed by librarians in private universities in Nigeria. The objective of the study was to analyse the virtual methods of service delivery among librarians and determine the predominant method used among the librarians. Survey research design was adopted for the study. Total enumeration technique was adopted for the study. A population of 181 librarians from 45 private universities in Southern Nigeria were involved. Data were gathered, analysed and presented using frequency counts, percentages, mean and standard deviation. The study found that librarians used different virtual methods of service delivery. Library website 157 (90%) and e-mail 132 (76.3%) were the prominent electronic media used by librarians while Facebook 59 (34%) and Whatsapp 57 (32.9%) were the predominant social media platforms applied for service delivery by librarians. Electronic media were more used for latest publications arrival, as well as library education and document delivery services while social media were more used for reference services and selective dissemination of information. In conclusion, virtual methods of service delivery were deployed by librarians in private universities for service delivery. In comparing the virtual methods, librarians used more of electronic media than social media to deliver services to their users. Therefore, electronic media were predominantly used than social media, many of the virtual methods were found to be underutilised while recommendations were proffered.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.12
• /
• pp.2394-2402
• /
• 2017

The frequency selective fading by multipaths determines a performance of underwater acoustic communication system in shallow littoral ocean. In this study, a characteristics of underwater acoustic channel and performance of multi-carrier system is evaluated in littoral ocean with a 50m deep water, an effective wave height of 0.5m and sandy mud bottom near Busan city. A multipath delay spread and time and frequency domain are presented as a function of a transmitter-to-receiver range. A bit-error-rate of a 5 channel 4FSK(Frequency Shift Keying) with a transmission rate of 1kbps, is examined and RS(Reed-Solomon) code is also adopted to remove a burst error due to time domain fading. A number of multipath are less than four and a bit-error-rate is decreased as an increase of a transmitter-to-receiver range which gives a congestion of multi-paths resulting in a decrease of time and frequency domain fading. The measured bit-error-rate is about 10-4 at greater than 600m of transmitter-to-receiver range.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.9
• /
• pp.799-804
• /
• 2016

Broadband powerline communication (BPLC) uses distribution lines as a medium for achieving effective bidirectional data communication along with electric current flow. As the material characteristics of power lines are not good at the communication channel, the development of power line communication (PLC) systems for internet, voice, and data services requires measurement-based models of the transfer characteristics of the network suitable for performance analysis by simulation. In this paper, an analytic model describing a complex transfer function is presented to obtain the attenuation and path parameters for a multipath power line model. The calculated results demonstrated frequency-selective fading in multipath channels and signal attenuation with frequency, and were in good agreement with the experimental results. Inductive coupling units are used as couplers for coupling the signal to the power line to avoid physical connections to the distribution line. The inductance of the ferrite core, which depends on the frequency, determines the cut-off frequency of the inductive coupler. Coupling loss can be minimized by increasing the number of windings around the coupler. Coupling efficiency was improved by more than 6 dB with three windings compared to the results obtained with one winding.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.16 no.10
• /
• pp.941-950
• /
• 1991

channel is severely degraded by multipath delay time spread. In this paper. We propose a simple multipath delay time detection method, which has a merit of in serviceable, yet simple H/W realizability for $\pi/4$ shift QPSK by detecting cross channel interference. A $\pi/4$ shift QPSK signal originally has quadrature channel(Q-ch) component. Thus in order to measure CCI between in-phase channel(I-ch) and quadrature channel(Q-ch), which closely related to multipath delay time, Frequency doubling scheme(frequency doubler) and differential detector is proposed, which makes $\pi/4$ shift QPSK signal look like BPSK and also makes it possible for CCI to be detected at I-ch detector output. To get an information from time varying I-ch output signal under the multipath lading environment, a method for obtaining the mean of the absolute value$(V_{MABS}(t))$ and another one for obtaining the root mean square value$(V_{RMS}(t))$ of CCI are proposed. Furthermore, a relationship between delay spread and CCI is also analyzed. In order to confirm theoretical results, computer simulation has been carried out under the quasi-static and Reyleigh distributed two ray multipath fading environments. A fairly good result was obtained. However it was also shown that this method is sensitive to bandwidth restriction to some extent. In addition, some idea for a simple hardware realization for the frequency doubler are given.

• The Journal of the Acoustical Society of Korea
• /
• v.38 no.1
• /
• pp.30-38
• /
• 2019

In recent years, researches on various communication methods have been conducted, particularly on OFDM (Orthogonal Frequency Division Multiplexing) and CDMA (Code Division Multiple Access) methods, as the use of underwater communication increases. While OFDM is, in general, advantageous in that it is resistant to Doppler in the water and it enables a high-speed communication, CDMA is resistant to frequency selective fading in the water and it can reduce energy consumption. Therefore, in this paper, we performed experiments in the shallow water in Western Sea of Korea to analyze the performance of OFDM and CDMA communication systems in the underwater channel environment. The maximum delay spread and Doppler spread were drawn by using the data obtained from the real sea area in order to analyze the underwater channel environment characteristics of the shallow water in Western Sea of Korea. The communication performances of OFDM and CDMA are shown as coded BER (Bit Error Rate) according to the variation of the maximum delay spread and the Doppler spread, respectively. The result of the analysis show that the OFDM method has more resistant performances to the underwater channel environment changes than the CDMA method.

• Journal of the Korean Vacuum Society
• /
• v.22 no.5
• /
• pp.238-244
• /
• 2013

Doping process using laser is an important process in fabrication of solar cell for heat treatment. However, the process of using the furnace is difficult to form a selective emitter doping region. The case of using a selective emitter laser doping is required an expensive laser equipment and induce the wafer's structure damage due to high temperature. This study, we fabricated a new costly plasma source. Through this, we research the selective emitter doping. We fabricated that the atmospheric pressure plasma jet injected Ar gas is inputted a low frequency (a few tens kHz). We used shallow doping wafers existing PSG (Phosphorus Silicate Glass) on the shallow doping CZ P-type wafer. Atmospheric plasma treatment time was 15 s and 30 s, and current for making the plasma is 40 mA and 70 mA. We investigated a doping profile by using SIMS (Secondary Ion Mass Spectroscopy) and we grasp the sheet resistance of electrical character by using doping profile. As result of experiment, prolonged doping process time and highly plasma current occur a deeper doping depth, moreover improve sheet resistance. We grasped the wafer's surface damage after atmospheric pressure plasma doping by using SEM (Scanning Electron Microscopy). We check that wafer's surface is not changed after plasma doping and atmospheric pressure doping width is broaden by increase of plasma treatment time and current.

• Geophysics and Geophysical Exploration
• /
• v.16 no.4
• /
• pp.211-216
• /
• 2013

In general, smoothing filters regularize functions by reducing differences between adjacent values. The smoothing filters, therefore, can regularize inverse solutions and produce more accurate subsurface structure when we apply it to full waveform inversion. If we apply a smoothing filter with a constant coefficient to subsurface image or velocity model, it will make layer interfaces and fault structures vague because it does not consider any information of geologic structures and variations of velocity. In this study, we develop a selective smoothing regularization technique, which adapts smoothing coefficients according to inversion iteration, to solve the weakness of smoothing regularization with a constant coefficient. First, we determine appropriate frequencies and analyze the corresponding wavenumber coverage. Then, we define effective maximum wavenumber as 99 percentile of wavenumber spectrum in order to choose smoothing coefficients which can effectively limit the wavenumber coverage. By adapting the chosen smoothing coefficients according to the iteration, we can implement multi-scale full waveform inversion while inverting multi-frequency components simultaneously. Through the successful inversion example on a salt model with high-contrast velocity structures, we can note that our method effectively regularizes the inverse solution. We also verify that our scheme is applicable to field data through the numerical example to the synthetic data containing random noise.