• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.9
• /
• pp.934-943
• /
• 1990

There are no turn-on losses in the series Resonant Converter which operates above the resonance frequency, and the commutation stress on the switched component is low. For a given Series Resonant Converter with specified load resistance, the output voltage is a function of the operation frequency. This paper describes the static and dynamic characteristic analysis of the Series Resonant DC to DC Converter, which is operating above the resonant frequency, with frequency control. For the analysis method, state plane technique is adopted, and the circuit operation is defined from normalized switching frequency, Fsn. Under this condition, circuit performance is analyzed ideally. The validity of the proposed analysis is verified by comparing with experimental results, the stability of the converter is confirmed against small variations around the operating point by conventional frequency domain analysis, and the stress quantity added to switch component is shown.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.12 no.2
• /
• pp.124-132
• /
• 1987

In this paper, a new Open and Closed Loop Alternation(OCLA) frequency synthesizer is developed to eliminate a frequency error occurring in the transition state of a frequency hopping. This frequency synthesizer consists of a phase comparator(PC), two low pass filters(LPF), two voltage controlled oscillators(VCO), switching elements, a programmable divider and frequency hopping controller, and the stabilized output frequency can be obtained by switching performance. In addigion, it can be found that the characteristic of its circuit construction makes it easy to attach an external circuitry to the open loop.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.109-109
• /
• 2009

This paper represented driving characteristic of a thin-type ultrasonic motor by fabricating and utilizing two kinds of drivers which could generate sinusoidal wave, square wave, respectively. A thin brass plate was used as a cross shaped vibrator and sixteen ceramic plates were attached on upper and bottom side of the brass plate. From the thin stator, elliptical displacements of the four contact tips were obtained. Speed, torque, and current were measured by applying sinusoidal waves through driving equipment such as function generator, power amplifier: to measure characteristic of the motor. As a result, the speed and the torque changed linearly at either driving frequency of 88.6 ~ 87.6[kHz] or voltage of 24~36[V]. Two-drivers which generate sinusoidal waves and square waves were designed respectively, and then were compared through some experiments in order to be put to practical use. In conclusion, the drivers had similar characteristic of speed-torque at similar frequency and voltage. It was able to control the motor linearly by using the driver generating square wave among two-drivers. Besides, it also was possible to make the drivers smaller.

• Journal of Advanced Navigation Technology
• /
• v.13 no.5
• /
• pp.714-719
• /
• 2009

In this paper, a compact antenna with band-rejected characteristic for Ultra-Wideband(UWB) applications is proposed. The designed antenna not only shows sufficient impedance bandwidth but has band-rejected characteristic for the frequency band of 5.15~5.825GHz limited by IEEE 802.11a and HIPERLAN/2. To obtain both properties of wideband band rejection, the techniques of a partial ground plane and embedded thin U-slot into planar radiator are used respectively. A designed antenna satisfied a VSWR less than 2:1 for the frequency band of 3.1~10.3GHz with band rejection of 4.90~5.92GHz.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.4 no.2
• /
• pp.122-129
• /
• 2001

A characterization procedure for analyzing symmetric coupled MIS(Metal-Insulator-Semiconductor) transmission line is used the same procedure as a general single layer symmetric coupled line with perfect dielectric substrate from the extraction of the characteristic impedance and propagation constant for even- and odd-mode. In this paper, an analysis for a new substrate shielding symmetric coupled MIS structure consisting of grounded crossbar at the interface between Si and SiO2 layer using the Finite- Difference Time-Domain(FDTD) method is presented. In order to reduce the substrate effects on the transmission line characteristics, a shielding structure consisting of grounded crossbar lines over time-domain signal has been examined. Symmetric coupled MIS transmission line parameters for even- and odd-mode are investigated as the functions of frequency, and the extracted distributed frequency- dependent transmission line parameters and corresponding equivalent circuit parameters as well as quality factor for the new MIS crossbar embedded structure are also presented. It is shown that the quality factor of the symmetric coupled transmission line can be improved without significant change in the characteristic impedance and effective dielectric constant.

• Journal of information and communication convergence engineering
• /
• v.16 no.1
• /
• pp.12-16
• /
• 2018

In this work, a voltage controlled oscillator (VCO) monolithic microwave integrated circuit (MMIC) was demonstrated for 10-GHz band motion detecting sensors. The VCO MMIC was fabricated using a $2-{\mu}m$ InGap/GaAs HBT process, and the tuning of the oscillation frequency is achieved by changing the internal capacitance in the HBT, instead of using extra varactor diodes. The implemented VCO MMIC has a micro size of $500{\mu}m{\times}500{\mu}m$, and demonstrates the value of inserting the VCO into a single chip transceiver. The experimental results showed that the frequency tuning characteristic was above 30 MHz, with the excellent output flatness characteristic of ${\pm}0.2dBm$ over the tuning bandwidth. And, the VCO MMIC exhibited a phase noise characteristic of -92.64 dBc/Hz and -118.28 dBc/Hz at the 100 kHz and 1 MHz offset frequencies from the carrier, respectively. The measured values were consistent with the design values, and exhibited good performance.

• Journal of IKEEE
• /
• v.24 no.3
• /
• pp.713-718
• /
• 2020

The method of measuring skin active points is a technique for obtaining a lot of biometric information because it is measured with convenience, low cost and non-invasive methods. In this paper, we used in a three electrode measure method that has the advantage of measuring the impedance of the APs under the skin. The impedance measuring method is well illustrated by a simple model of an equivalent electrical circuit that correlates well with experimental results. The characteristic frequencies of APs are about 15-30HZ higher than that of surrounding skin and the values of measured reactance are about 35-77KΩ smaller. This technology analyzed accurately and objectively the reactance and characteristic frequency of APs and the surrounding skin using a non-invasive measuring system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.1341-1346
• /
• 2001

In this study, the acoustic properties of steel-wire sound absorbing materials with different thickness and bulk density were investigated in terms of characteristic impedance, propagation constant, and absorption coefficient. The well-known two-cavity method was used for evaluating those acoustic parameter values in experiments. Also, in order to validate the experimentally measured values, the results were compared with the results obtained from Chung and Blaser's transfer function method and SWR method. The experimentally measured values of normal absorption coefficients were generally agreed well with the corresponding values from the transfer function method and the SWR method. Based on the experimental results, the following conclusions could be made. The magnitude of the absorption coefficient and the frequency range of the maximum absorption coefficient were controllable by changing the thickness and bulk density of the sound absorbing materials. Also, the magnitude of the absorption coefficient depended on the characteristic impedance and the propagation constant. As large as the air cavity depth at the rear side of the steel-wire sound absorbing materials, the maximum magnitude of the absorption coefficient occurred at the lower frequency ranges.

• Earthquakes and Structures
• /
• v.20 no.4
• /
• pp.457-471
• /
• 2021

This study aims at providing a simple and effective methodology to define a meaningful characteristic period for special class of earthquake records named "pulse-like ground motions". In the proposed method, continuous wavelet transform is employed to extract the large pulse of ground motions. Then, Fourier amplitude spectra obtained from the original ground motion and the residual motion is simply compared. This comparison permits to define a threshold pulse-period (Tp∗) as the threshold period above which the pulse component has negligible contributions to the Fourier amplitude spectrum. The effect of pulse on frequency content of motions was discussed on the light of this definition. The advantage and superior features of the new definition were related to the inelastic displacement ratio (IDR) for single-degree-of-freedom systems with period equal to one half of the threshold period. Analyses performed for the proposed period at three ductility levels u=2,4,6 were compared with the results obtained at half of pulse period derived from wavelet analysis, peak-point method and the peak of product of the velocity and the displacement response spectra (Sv x Sd). According to the results, pulse effects on inelastic displacement ratio seem to be more important when $\frac{T_p^*}{T}=2$ (T is the fundamental vibration period of system). The results showed that utilizing of the proposed definition could facilitate an enhanced understanding of pulse-like records features.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.437-442
• /
• 2005

This paper deals with the measurement and analysis of radio characteristic of 424 MHz for using the automation of transmission and supply of electric power, ana automatic meter reading(AMR). Normally radio propagation characteristic is the base of system design, performance evaluation and choice of position of the base station in wireless communication. It is the most accurate way to design a base station through practical measurements, but it costs much time, money and engineers. So, we developed 424 MHz short range wave propagation model for AMR service.