• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.659-662
• /
• 2002

The present paper presents the experimental results for pressure drop in inclined tube bundles located in a rectangular duct. Measurements are made for pressure drop in triangular and rotated triangular tube arrays having P/d ratio of 1.6 and inclination angles of 30,45,60 and 90 degrees. The Reynolds number based on the free stream velocity and tube diameter ranges from $8{\times}10^2\;to\;6.3{\times}10^{4}$. The experimental results show that the magnitude of dimensionless pressure drop decreases significantly when the inclined angle is less than 45 degree. The measured data are compared with two existing correlations available in the literatures. The ESDU correlation agrees well with the present data far the triangular arrays. But some discrepancies are observed for the rotated triangular arrays when the inclined angles are 30 and 45 degrees. The Idel'chik correlation generally agrees well with the measured data for the rotated triangular arrays except for the inclined angle of 30 degree. The Idel'chik correlation needs modification for the triangular arrays. The modified Idel'chik correlation agrees well with the measured data within $10{\%}$. It is found that the present measured data can be applied to the evaluation and modification of previous correlations.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1997년도 추계학술대회
• /
• pp.380-384
• /
• 1997

This study was performed to understand the exogenous-water-drop induced thermomechanical effect on the tooth in the free-running Er:YAG laser mode for the proper use of water as a laser energy absorber and coolant in dentistry. The ree-running Er:YAG laser was used in the dental hard tissue ablation study. A Microjet system was employed to dispense precise water drops. Ablation rate, recoil momentum, and temperature rise in the pulp cavity were measured with and without an exogenous water drop on the tooth surface. Exogenous water enhanced ablation rate in the thick tooth in which the ablation rate on the dry surface does not increase linearly but shows plateau. Optimal exogenous water volume was shifted from 2 nl to 4 nl as the laser energy was increased from 48 mJ to 145 mJ. The magnitude of the recoil momentum was increased as the volume of exogenous water increased. The results of this study suggest that we must pay attention to the recoil momentum or recoil pressure study or the optimal and safe usage of water in the dental treatment because these mechanical effects depend on the volume of exogenous water on the tooth surface.

• 한국군사과학기술학회지
• /
• 제14권3호
• /
• pp.397-404
• /
• 2011

The aerodynamic characteristics of a separated captive body in flow field around aircraft are studied to observe aerodynamic stability for safe separation from aircraft. Since the captive body separated from aircraft is initially exposed to unsteady flow pattern, the change of aerodynamic forces and moments should be measured to analyze how the flow pattern affects on the captive body at the vicinity of aircraft. Aerodynamic forces and moments of the separated captive body are measured at selected positions along predictable dropping trajectories. The measuring trajectories, generated by the free drop test of the dropping model in the wind tunnel, are consisted of 9 possible lines by free dropped trajectories. Experimental results show that the aerodynamic forces and moments are significantly varied with the distance between the captive body and aircraft. In conclusion, the change of aerodynamic characteristics within flow field around aircraft should be considered to simulate trajectories of the separated captive body from aircraft.

• Nuclear Engineering and Technology
• /
• 제55권1호
• /
• pp.330-338
• /
• 2023

In this study, impacts of an enhanced-moderation Fuel Assembly (FA) named Truly Optimized PWR (TOP) lattice, which is modified based on the standard 17 × 17 PWR FA, are investigated in a natural circulation Soluble-Boron-Free (SBF) Small Modular Reactor (SMR). Two different TOP lattice designs are considered for the analysis; one is with 1.26 cm pin pitch and 0.38 cm fuel pellet radius, and the other is with 1.40 cm pin pitch and 0.41 cm fuel pellet radius. The NuScale core design is utilized as the base model and assumed to be successfully converted to an SBF core. The analysis is performed following the primary coolant circulation loop, and the reactor is modelled as a single channel for thermal-hydraulic analyses. It is assumed that the ratio of the core pressure drop to the total system pressure drop is around 0.3. The results showed that the reactor power could be increased by 2.5% and 9.8% utilizing 1.26/0.38 cm and 1.40/0.41 cm TOP designs, respectively, under the identical coolant inlet and outlet temperatures as the constraints.

• 마이크로전자및패키징학회지
• /
• 제22권3호
• /
• pp.1-7
• /
• 2015

In this study, properties of Pb-free solders for automotive electronics parts were discussed. Lead-free solders for electronics became important after RoHS (Restriction of the use of certain Hazardous Substances) to avoid environmental pollution. Also the growing electronic rate in automotive parts and ELV (End-of Life Vehicles) make Pb-free solder for automotive electronics to be inevitable trend. Definitely, Pb-free solder for automotive electronics should have good wettability, basic strength, but need more reliability than other solders, since it has harsh condition like high temperature, humidity and engine vibration. Thus, shear strength test, thermal shock, drop test and many others are needed to ensure the high reliability. This study describes the properties and requirements of Pb-free solders for automotive electronics.

• 한국군사과학기술학회지
• /
• 제20권1호
• /
• pp.81-89
• /
• 2017

This study investigates store separation characteristics of an unmanned aerial vehicle having generic stealth configuration over unsteady flow of an internal bay. Free-drop wind tunnel tests are conducted to simulate bomb releases from an internal weapons bay while high-speed camera images are taken. The images are analyzed to examine the effects of flow velocity, angle of attack, flap deflection and the ejector force application on the store separation trajectories. For the free-drop wind tunnel tests, Froude Scaling is applied to match the dynamic similarity for the bomb model, and the ejector force is simulated by using small pneumatic cylinders. The results indicate that the test bomb model safely separates from the internal bay at the given test conditions and configurations. It is also observed that the effects of the flow velocity and ejector force application have greater impacts on the separation trajectories than those of angle of attack and flap deflection.

• 마이크로전자및패키징학회지
• /
• 제15권4호
• /
• pp.77-86
• /
• 2008

본 연구에서는 유연솔더인 63Sn37Pb와 무연 솔더인 95.5Sn4.0Ag0.5Cu와 97Sn2.5Ag0.5Cu BGA(Ball Grid Array) 패키지를 인쇄회로기판(Printed Circuit Board, PCB)에 위치에 따라 장착하고 보드레벨의 낙하시험(Board Level Drop Test)을 실시하여 충격에 대한 유 무연 솔더의 특성을 분석하였고 4점굽힘시험(board Level 4-point Bending Test)을 실시하여 굽힘에 대한 솔더볼의 기계적 저항특성을 분석하였다. 또한 유한요소법(Finite Element Modeling, FEM)을 이용해 낙하시험과 4점굽힘시험에서 솔더 조인트에 미치는 응력과 변형률을 해석하였으며, 시험 설계 시에 솔더 조인트의 응력변화에 영향을 미칠 수 있는 변수를 고려하여 해석하고 결과를 비교 분석하였다. 낙하시험과 4점굽힘시험에서 모두 무연솔더는 유연솔더보다 2배 이상 높은 신뢰성을 보였으며, PCB의 중앙에 위치한 패키지는 외각에 위치한 패키지 보다 매우 낮은 신뢰성을 보였다. 유한요소법을 통해 해석한 결과 최외각 솔더에서 가장 큰 응력이 발생하였고, 솔더의 조성과, 시험설계변수에 의해 응력의 발생 정도가 다름을 나타내었다.

• 대한화장품학회지
• /
• 제47권1호
• /
• pp.31-40
• /
• 2021

프레스드 파우더의 주요 안정성 요인으로 경도와 낙하 안정도가 있다. 일반적으로 탈크가 포함된 프레스드 파우더의 경우 경도와 낙하 안정도를 고르게 충족시키며 사용감도 우수하지만 최근 탈크의 석면 이슈로 인해 대체를 원하는 고객들이 늘고 있다. 따라서 안정성을 유지하면서 사용감도 떨어지지 않는 탈크 프리 프레스드 파우더 제형의 개발이 시급하다. 본 연구에서는 탈크 프리 프레스드 파우더를 만들기 위한 최적의 원료 배합 비율을 찾기 위한 실험을 진행하였다. 파우더에 주로 사용되는 원료들의 특성을 확인하고 비율을 변화시켜 실험하여 명도와 경도를 측정하고 낙하 시험을 실시하였다. 천연 마이카 함량이 합성 마이카보다 많거나, 코팅된 실리카 대신 논 코팅 실리카를 사용할 경우 탈크가 포함된 내용물보다 경도와 낙하 안정도는 낮지만 명도는 유사하였다. 반대로 합성 마이카 함량이 천연 마이카 함량과 동일하거나 높을 경우, 코팅된 실리카 함량이 논코팅 실리카 함량과 동일하거나 높은 경우에 탈크가 포함된 내용물의 경도, 낙하 안정도와는 유사하였으나 명도는 낮게 측정되었다. 탈크가 포함된 내용물보다 경도는 높지만 낙하 안정성은 떨어지는 현상도 발견하여 경도와 낙하 안정성의 상관관계에 대해서는 추가적인 연구가 필요할 것으로 생각된다.

• Journal of Welding and Joining
• /
• 제15권3호
• /
• pp.36-46
• /
• 1997

Dynamics of molten drop detachment in the Gas Metal Arc (GMA) welding is investigated using the Volume of Fluid(VOF) method. The electromagnetic effects are included in the formulation of the VOF method which has been widely used to analyze the dynamics of the fluid having a free surface. The molten drop geometry, pressure and velocity profiles within the drop are calculated numerically in the cases of globular and spray transfer modes. It appears that the velocity and current distribution affect metal detachment. It is found that the taper is formed and maintained during the spray transfer by the electromagnetic force. Predicted results show reasonably good agreement with the available experimental data which validates the application of the VOF method to metal transfer analysis.

• Journal of Welding and Joining
• /
• 제15권5호
• /
• pp.84-91
• /
• 1997

The metal transfer phenomenon of the pulsed-GMAW is simulated by formulating the electromagnetic force incorporated with the Volume of Fluid algorithm. The free surface profiles, pressure and velocity distributions within the drop are computed numerically. Axial velocity and acceleration generated during peak current period are found to have a significant effect on drop detachment. Therefore, the accelerated inertia force becomes one of important factors affecting metal transfer in the pulsed-GMAW. When the pulse current parameters are selected properly, the molten drop is detached just after current pulse, and the operating range of the pulsing frequency increases with higher peak current and duty cycle. Calculated operating ranges show reasonably good agreements with the available experimental data.