• 한국해양공학회지
• /
• 제19권2호
• /
• pp.47-52
• /
• 2005

This paper introduces a procedure for free span and fatigue analysis of offshore pipelines per DNV-RP-F105, 2002. The new method includes the axial force and deflection load in pipelines. The screening criteria were established to calculate the allowable span lengths in the new design codes. The screening criteria allows a certain amount of vortex-induced vibration due to wave and current loading. However, the induced pipe stresses are very small and usually below the limit stresess of typical S-N curves. In contrast, the conventional criteria did not allow any vortex-induced vibration in the free span of pipelines. Thus, the screening criteria yields reduced allowable span lengths. A simplified procedure was established to calculate the fatigue damage due to long-term current distribution. The long-term current statistics was assumed with a 3-parameter Weibull distribution. The fatigue damage was estimated for the span lengths obtained from the screening criteria for various conditions. Sample calculations show the effect of axial force for various boundary conditions. Comparisons with conventional criteria are included.

• 한국안전학회지
• /
• 제13권1호
• /
• pp.3-12
• /
• 1998

On the stability of the cantilever beam subjected to a follower force at the free end, the influences of the translational spring and the moment of inertia of a tip mass at the free end have been studied by numerical methods. The centroid of a tip mass is offset from the free end of a Beam and is located along its extended axis to vary the value of moment of inertia of a tip mass. It is proved that as the constants of a spring supporting the free end are augmented, the critical flutter loads of the above system decrease, whereas they increase without a tip mass.

• Journal of Welding and Joining
• /
• 제18권6호
• /
• pp.74-82
• /
• 2000

The fluxless wetting properties of UBM-coated Si-wafer to the binary lead-free solders(Sn-Ag, Sn-Sb, Sjn-In, Sn0Bi) were estimated by wetting balance method. With the new wettability indices from the wetting curves of one side coated specimen, the wetting property estimation of UBM-coated Si-wafer was possible. For UBM of Si-chip, Au/Cu/Cr UBm was better than au/Ni/TI in the point of wetting time/ At general reflow process temperature, the wettability of high melting point solders(Sn-Sb, Sn-Ag) was better than that of low melting point one(Sn-Bi, Sn-In). The contact angle of the one side coated Si-plate to the solder could be calculated from the force balance equation by measuring the static state force and the tilt angle.

• Structural Engineering and Mechanics
• /
• 제33권6호
• /
• pp.709-724
• /
• 2009

In this paper a free-free uniform beam with damping effects subjected to follower and transversal forces at its end is considered as a model for a space structure. The effect of damping on the stability of the system is first investigated and the effects of the follower and transversal forces on the vibration of the beam are shown next. Proportional damping model is used in this work, hence, the effects of both internal (material) and external (viscous fluid) damping on the system are noted. In order to derive the frequency of the system, the Ritz method has been used. The mode shapes of the system must therefore be extracted. The Newmark method is utilized in the study of the system vibration. The results show that an increase in the follower and transversal forces leads to an increase of the vibrational motion of the beam which is not desirable.

• 한국정밀공학회지
• /
• 제12권4호
• /
• pp.39-45
• /
• 1995

본 논문은 복수 집중질량을 갖고 제어 종동력을 받는 자유 Timoshenko보의 동적 안정성에 관한 것으로, 비행중의 미사일이나 로켓의 연료탱크, Payload등의 기계장치부를 복수의 집중질량으로 간주하여 이러한 항공우주 구조물들이 추진력인 종동력을 받을때에 대한 계의 동적 안정성을 판별한다. 수학적 모델에 대한 운동방정식은 확장된 해밀톤 원리를 이용한 유한요소법에 의해 유도되며, 복수 부가질량의 위치 및 크기변화, 센서의 위치 및 게인(gain)의 변화에 따른 계의 안정성 지도(stability maps)를 보여준다. 또한 보의 전단 변형이나 회전관성의 효과 뿐만아니라, 추질력의 방향이 제어되는 경우와 제어되지 않는 경우에 대한 최대 추진력 값이 수치 시뮬레이션을 통해 예측된다.

• 천문학논총
• /
• 제18권1호
• /
• pp.15-20
• /
• 2003

In the earlier papers we analyzed the axisymmetric, nonstationary electrodynamics of the central black hole and a surrounding thin accretion disk in an active galactic nucleus. Based on those papers we analyze the axisymmetric, nonstationary black hole magnetosphere in this paper. We concentrate on deriving the ‘Grad-Shafranov equations’; both in the force-free and non-force-free cases. In the time-independent limit our equations naturally coincide with stationary equations as they should.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2006년도 추계 학술대회논문집
• /
• pp.9-10
• /
• 2006

A numerical method for simulating tree surface flows including the surface tension is presented. Numerical scheme is based an a fractional-step method with a finite volume formulation and the interface between liquid and gas is tracked by Volume of Fluid (VOF) method. Piecewise Linear Interface Calculation (PLIC) method is used to reconstruct the interface and the surface tension is considered using a Continuum Surface Force (CSF) model. Several free surface flow phenomena were simulated to show its effectiveness to find such phenomena.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2000년도 추계학술대회 논문집(Proceeding of the KOSME 2000 Autumn Annual Meeting)
• /
• pp.108-114
• /
• 2000

The excitation forces from the periodical firing pressure in cylinder and the rotating crank mechanism cause lots of vibration problems in diesel engine. In this paper, the theoretical formulas for excitation forces are introduced and computational program for the optimization of crank angle is also developed to reduce the free moments in diesel engine. The computational results of 4-stroke in-line engine are applied to verify the reliability of the program.

• 소음진동
• /
• 제4권2호
• /
• pp.147-154
• /
• 1994

In this study, ultransonic vibration cutting system was contructed by installing throw-away-tool tip (KT 350) by screw lock on the bending vibration mode in free-free beam. During the conventional cutting and ultransonic conventional cutting of SM45C, variations of cutting force, roughness and acceleration were measured. The results were compared and analyzed in detail, and it was found that the ultransonic vibration cutting was more effective in reducing cutting force compareed with the conventional cutting .

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제8권6호
• /
• pp.589-601
• /
• 2016

The hybrid grid was adopted and numerical prediction analysis of propeller unsteady bearing force considering free surface was performed for mode and full-scale KCS hull-propeller-rudder system by employing RANS method and VOF model. In order to obtain the propeller velocity under self-propulsion point, firstly, the numerical simulation for self-propulsion test of full-scale ship is carried out. The results show that the scale effect of velocity at self-propulsion point and wake fraction is obvious. Then, the transient two-phase flow calculations are performed for model and full-scale KCS hull-propeller-rudder systems. According to the monitoring data, it is found that the propeller unsteady bearing force is fluctuating periodically over time and full-scale propeller's time-average value is smaller than model-scale's. The frequency spectrum curves are also provided after fast Fourier transform. By analyzing the frequency spectrum data, it is easy to summarize that each component of the propeller bearing force have the same fluctuation frequency and the peak in BFP is maximum. What's more, each component of full-scale bearing force's fluctuation value is bigger than model-scale's except the bending moment coefficient about the Y-axis.