• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.507-512
• /
• 2000

The ob.jective of this study is to determine fracture behaviors(penetrati0n modes) and resistance to penetration duringballistic impact of Al 5052-H34 alloy laminates and anodized Al 5052-H34 alloy laminates. Resistance to penetration is determined by $V_{50}$ ballistic limit, a statical velocity with 50% probability for complete penetration, test method. Fracture behaviors and ballistic tolerance, described by penetration modes, are respectfully observed that result from V50 test and Projectile Through Plates (PTP) test at velocities greater than $V_{50}$. PTP tests were conducted with 0" obliquity at room temperature using 5.56mm ball projectile. $V_{50}$ tests with 0" obliquity at room temperature were conducted with projectiles that were able to achieve near or complete penetration during PTP tests. Surface Hardness, resistance to penetration, and penetration modes of A1 5052-H34 alloy laminates compared to those of anodized Al 5052-H34 alloy laminates.y laminates.

• 대한치과기공학회지
• /
• 제23권2호
• /
• pp.95-103
• /
• 2002

For this study, self curing resin and heat curing resin used for existing usual resin denture base in the denture industry were chosen by manufacturer. Curing tests for 30-minute, I-hour, 2-hour and 3-hour were conducted to know the strength of the resins and conduct analysis to get other necessary information. The results obtained are as follows: 1. Heat curing resins show a little differences among the manufacturers. However 30-minute curing resin shows great difference as shown in the fracture strength test. 2. The effect from the granularity of the resins on the fracture strength was found insignificant which means there is no difference between coherence and strength. 3. To summarize the results from each time level, the longer the time is, the more the minute cracks on the surface, which is the cause of reduced strength. From this test, it was identified that in making the denture base for patients in dental clinics, 30-minute curing is most efficient and effective in reducing discoloration and monomers, although long-time curing has been considered to be the principal.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2006년도 춘계 학술발표회 논문집
• /
• pp.1132-1141
• /
• 2006

Recently it is difficult to secure sand used in the improvement of soft ground, and so it is necessary to find alternative materials. For this reason many researchers are studying and trying to find new substitute materials. One of the materials is considered as converter slag by wind fracture which is generated in the production of steel manufacture by electric circuit. It is environment friendly since it is a recycled material and economical since it is cheaper than sand. To investigate the applicability of converter slag by wind fracture as the alternative material such as vertical drains, it is necessary to check the drainage effect of this in the field construction. In order to attain an successful design it is important to predict problems encountered in field construction. Accordingly, in this study the laboratory test was executed under different conditions in advance of applying of the field. A total of 4 cases including slag, sand+slag, pack slag and sand as vertical drains was conducted, and at the base of the laboratory test the field test was executed and analyzed.

• 한국표면공학회지
• /
• 제46권1호
• /
• pp.42-47
• /
• 2013

The strain-induced phase transformation from austenite to martensite is responsible for the high strength and ductility of TRIP steels. However high strength steels are susceptible to hydrogen embrittlement. This study aimed to evaluate the effects of hydrogen on the behavior of hydrogen delayed fracture in TRIP steel with hydrogen charging conditions. The electrochemical hydrogen charging was conducted at each specimen with varying current density and charging time. The relationship between hydrogen concentration and mechanical properties of TRIP steel was established by SP test and SEM fractography. The maximum loads and displacements of the TRIP steel in SP test decreased with increasing hydrogen charging time. The results of SEM fractography investigation revealed typical brittle mode of failure. Thus it was concluded that hydrogen delayed fracture in TRIP steel result from the diffusion of hydrogen through the ${\alpha}$' phase.

• Computers and Concrete
• /
• 제2권6호
• /
• pp.499-516
• /
• 2005

A composite model is used to represent the heterogeneity of plain concrete consisting of coarse aggregates, mortar matrix and the mortar-aggregate interface. The composite elements of plain concrete are modeled using triangular finite element units which have six interface nodes along the sides. Fracture is captured through a constitutive single branch softening-fracture law at the interface nodes, which bounds the elastic domain inside each triangular unit. The inelastic displacement at an interface node represents the crack opening or sliding displacement and is conjugate to the internodal force. The path-dependent softening behaviour is developed within a quasi-prescribed displacement control formulation. The crack profile is restricted to the interface boundaries of the defined mesh. No re-meshing is carried out. Solutions to the rate formulation are obtained using a mathematical programming procedure in the form of a linear complementary problem. An event by event solution strategy is adopted to eliminate solutions with simultaneous formation of softening zones in symmetric problems. The composite plain concrete model is compared to experimental results for the tensile crack growth in a Brazilian test and three-point bending tests on different sized specimens. The model is also used to simulate wedge-type shear-compression failure directly under the loading platen of a Brazilian test.

• Composites Research
• /
• 제24권5호
• /
• pp.39-43
• /
• 2011

탄소나노튜브로 보강된 고분자 수지에 대한 연구는 지난 20년간 활발히 수행되어 왔다. 또한 이를 이용하여 탄소섬유복합재의 물성을 증대시키기 위한 연구도 최근 그 영역을 넓혀가고 있다. 탄소섬유복합재는 탄소섬유의 비약적인 발전으로 섬유 방향의 기계적 물성은 상당히 만족할 만한 수준에 도달했으나, 수지에 의해 좌우되는 기계적 물성은 아직 기대에 못미치고 있다. 특히, 층간의 분리 (delamination)는 탄소섬유복합재의 가장 전형적이며 치명적인 파손의 원인중 하나이다. 이 층간분리에 대한 저항성을 알아보는 모드 1 파괴인성 실험 (혹은 double cantilever beam, DCB test)을 다양한 작용기로 기능화된 SWNT가 첨가된 탄소섬유복합재 시편에 대하여 수행하였다. 부직포 형태의 탄소나노튜브층을 이용한 시편의 경우 10.6%의 파괴인성 증대를 보였다.

• 대한기계학회논문집A
• /
• 제34권9호
• /
• pp.1299-1304
• /
• 2010

압연실험을 통해서 폭 방향 변형 편차가 존재하는 실리콘 강판의 가공파손을 고찰하였다. 폭 방향 변형 편차는 강판에 웨이브를 발생시키고 압연방향으로 소재의 에지 부위(혹은 센터 부위)에 인장(혹은 압축)을 준다. 실제 압연기에서 발생하는 웨이브를 실험실적으로 구현하기 위해서 공형롤을 설계 및 제작하였다. 실험에 사용한 소재는 고-실리콘(약 3%) 강판이다. 본 실험을 통해서 센터 웨이브에 의해 발생되는 에지 부위 인장응력이 가공파손에 가장 지배적인 요인이라는 것이 제시되었다. 센터 웨이브를 일으키는 폭 방향 변형 편차의 정도에 따라 에지 파손과 지그재그 형태의 시편 중심 절손을 유발한다는 결과도 도출하였다.

• 대한기계학회논문집A
• /
• 제40권3호
• /
• pp.253-258
• /
• 2016

입자강화복합재료를 이용하여 쐐기분열시험으로부터 얻은 파괴에너지, 균열진전 및 CTOD 에 대한 온도의 영향이 조사되었다. 이용된 재료는 고분자바인더, 산화제 및 알루미늄입자로 이루어져 있으며, 쐐기분열시편의 시험 속도는 50 mm/min 이고, 온도 조건은 $50^{\circ}C$, 상온, $-40^{\circ}C$, $-60^{\circ}C$이었다. 분열하중-CMOD 로부터 구한 파괴에너지는 $50^{\circ}C$에서 $-40^{\circ}C$까지 온도의 감소와 함께 증가한다. 또한 $-60^{\circ}C$에서 입자강화복합재료의 강도는 유리전이온도에 의해 급격히 증가하며 취성거동을 보였다. 그리고 디지털 이미지 상관법을 이용하여 균열 선단부근에 대한 변형률장이 분석되었다.

• 한국해양공학회지
• /
• 제29권6호
• /
• pp.445-453
• /
• 2015

The stress triaxiality and lode angle are known to be most dominant fracture parameters in ductile materials. This paper proposes a three-dimensional failure strain surface for a ductile steel, called a low-temperature high-tensile steel (EH36), using average stress triaxiality and average normalized lode parameter, along with briefly introducing their theoretical background. It is an extension of previous works by Choung et al. (2011; 2012; 2014a; 2014b) and Choung and Nam (2013), in which a two-dimensional failure strain locus was presented. A series of tests for specially designed specimens that were expected to fail in the shear mode, shear-tension mode, and compression mode was conducted to develop a three-dimensional fracture surface covering wide ranges for the two parameters. This paper discusses the test procedures for three different tests in detail. The tensile force versus stroke data are presented as the results of these tests and will be used for the verification of numerical simulations and fracture identifications in Part II.

• 한국가스학회지
• /
• 제16권3호
• /
• pp.54-64
• /
• 2012

실 배관을 평가하는 DWTT (Drop Weight Tearing Test)의 파괴인성 값은 실 배관의 파괴인성 값 및 연성취성천이 온도를 예측할 수 있는 실험방법이므로, 최근 DWTT의 값에 대한 중요성이 증가되고 있다. 본 연구에서는 API X70과 API X65 라인파이프강의 DWTT 후의 온도에 따른 연성파면율, 역파면율, 흡수에너지와 온도 $-60^{\circ}C$~상온)와의 관계를 비교분석 하고자 하였다. X65과 X70의 값에서 마찬가지로 연성파면율 및 흡수에너지는 온도가 낮아질수록 함께 낮아지는 경향을 보였으며, X70의 경우에는 $-40^{\circ}C$ 까지 연성파괴를 보이는 반면, X65는 $-30^{\circ}C$ 까지 연성파괴를 보였다.