• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.2
• /
• pp.95-101
• /
• 2013

This paper presents the comparison of the earth resistivity obtained from the measurements made with the three-electrode and four-electrode fall-of-potential techniques. The ${\rho}-a$ curve obtained from Wenner four-electrode method in undisturbed earth is in good agreement with the ${\rho}-l$ curve obtained from the three-electrode method based on the fall-of- potential method. However, The ${\rho}-a$ curve in disturbed earth with moisture and freezing is significantly different with the ${\rho}-l$ curve. The ${\rho}-a$ curve is considerably sensitive to the freezing and the moisture present in the earth surface compared to the ${\rho}-l$ curve. Thus to determine the actual earth resistivity, it is necessary to take into account the earth surface conditions when measuring the earth resistivity.

• Journal of IKEEE
• /
• v.23 no.4
• /
• pp.1122-1127
• /
• 2019

In this study, the bio-impedance of the human body is able to obtain a lot of information by monitoring the pathological and physiological conditions of clinical and biological tissues. The four electrode method system for biometrics measured the potential difference between two electrodes and the other two electrodes were used as electrodes for current flow. The newly developed dry gold electrode measured impedance from 1 Hz to 50 kHz and produced reproducible results. To verify the impedance measurement of the dry electrode, the pitting was performed using an equivalent circuit model of the bioelectrode skin, and the effectiveness was demonstrated through modeling. Fixed electrode types have a constant position of the electrodes attached during the measurement, so that a stable measurement can be obtained, thereby minimizing the error.

• Journal of Biomedical Engineering Research
• /
• v.35 no.6
• /
• pp.234-241
• /
• 2014

This study was designed to investigate the effects of stimulation intensity and inter-electrode distance on the parameters of the measured sensory nerve signal. 30 healthy subjects participated in this study. Sensory nerve signals were elicited by four different pulse amplitudes, i.e., 3, 6, 9, 12 mA, with the pulse width fixed at $500{\mu}s$. The sensory nerve signals elicited by the four different pulse amplitudes were measured by four different inter-electrode distances (20, 30, 40, and 50 mm). We extracted four parameters (pulse amplitude, pulse width, pulse area, and latency time from stimulation) from the sensory nerve signals. The measured pulse amplitude and pulse width were increased when the measuring inter-electrode distance was increased while the stimulating pulse amplitude was fixed. The measured pulse amplitude was saturated with the stimulating pulse amplitudes of over 6 mA while measuring inter-electrode distance. Under the same condition, measured pulse width was increased, and sensory nerve signal was initiated early. Sensory nerve signals, specially those of pulse amplitude, were distorted by a differential amplification method that commonly measures the human body signal. The experimental results indicate that the differential amplification method is required to be replaced when measuring nerve signals. Our observations suggested that the hyperpolarization of the action potential of the sensory nerve signal for preventing distortion could be used to clarify the correlation between the parameters of the sensory nerve signals and quantification of sensations.

• Journal of Biomedical Engineering Research
• /
• v.25 no.3
• /
• pp.227-233
• /
• 2004

In this paper, it is proposed that the four channel electrode arrangement at a frontal lobe and the noise reduction method using a JADE for the EEG biofeedback system. The proposed electrode arrangement is based on the retina-cornea dipole model. Using JADE and signals which are acquired by the proposed arrangement, four independent components are separated. To estimate a pure EEG component among four components, it is measured that a ratio of alpha wave to the whole signal and then the component that has a maximum value is considered as a pure EEG which the noise is eliminated. As a result of experiments, the proposed methods are effective in reduction of noises during acquisition of the EEG.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.50 no.11
• /
• pp.575-580
• /
• 2001

In this paper, using $500\mum-thickness\; (100)\; silicon\; wafer,\; flat\; 65\mum-thickness$ silicon mirror plates were fabricated through dry etching and wet etching, and $45\mum-depth$ grooved driving electrodes were fabricated through UV-LIGA process. Four shapes of the driving electrode were fabricated: twenty four grooves of the $50\mum-width$, twelve grooves of the $100\mum-width$, six grooves of the $200\mum-width$, and no grooves on the driving electrode. Fabricated mirror plate size and spring size are $2400\times2400\times65\mum3\; and \;500\times10\times65\mum3,$ respectively. Mirror plate parts and driving electrodes were assembled into the scanning mirrors. Measured natural resonance frequencies were about 600Hz which have error within $\pm 2%$ to calculated value. Due to the squeeze effect in the narrow gap between the mirror plate and the driving electrode, measured resonance frequencies were reduced as raising the amplitude of the mirror plate. In a case of driving electrode without grooves, the resonance frequency was reduced largely, compared with a case of driving electrode with grooves. According to the experimental results, squeeze effect was smaller in the driving electrode with smaller-width and many grooves. Therefore, the driving electrode with smaller-width and many grooves was effective in low voltage and high speed operation.

• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.207-212
• /
• 2001

Electro-Rheological(ER) fluid are suspensions which show an abrupt increase in rheological properties under electric fields. ER effects arise from electrostatic forces between the starch particles dispersed in the electrically insulating silicone oil, induced when an electric field is applied. Yield stress of the fluids were measured on the couette cell type rheometer as a function of electric fields. This paper presents performance analyses of four types of the two parallel-plate. Which have different electrode length and width but same electrode area. On the basis of the pressure drop and flow rate analysis. Four types of the two parallel-plate are designed and manufactured. Using ER fluid, it is possible to directly interface between electric signals and fluid power without moving parts.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1024-1026
• /
• 2004

We have developed the five mask $PMOS^1$ and the six mask CMOS process architecture for poly-Si TFT. In order to have a competitive process with that for a-Si TFT, the simple co-planar electrode structure whose data line electrode and pixel electrode are on the same plane was adopted. In addition, RGB + White four color $technology^2$ were applied to achieve high aperture ratio and transmittance. Using the aforementioned process architecture and four color technology, 2.0 inch qCIF transmissive micro-reflectance (TMR) device was successfully fabricated.

• Journal of the Korean Chemical Society
• /
• v.20 no.2
• /
• pp.129-135
• /
• 1976

A direct-reading conductance measuring system using a potentiostatic circuit and a four-electrode conductance cell was devised. The difficulties with the traditional method of using the Wheatston bridge and a two-electrode cell due to the complicated nature of the electrochemical system, the double layer capacitance and the Faradaic impedance at the electrodes, etc., could be avoided in this method. The devised instrument proved to be convenient and suitable for precise measurements. The results of measured conductivities of KCl and HCl solutions are reported.

• Proceedings of the KOSOMBE Conference
• /
• v.1991 no.11
• /
• pp.98-100
• /
• 1991

We studied the characteristics of the compound electrode and found that the compound electrode provides the four-electrode method in a compact form. We developed a new method of measuring the skin impedance using simple electrodes at low frequencies. At high frequencies where the effect of internal tissue impedance is not negligible, we used the compensation method using compound electrodes since they measure the voltage right under the skin. At 50 kHz, we measured the real part of the skin impedance of less than $80\;{\Omega}$ on the thorax.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.05a
• /
• pp.100-100
• /
• 2009

$TiO_2$ is widely being used as a semiconductor electrode for DSSC. Anti-recombination property and surface area of $TiO_2$ give an important influence to the DSSC efficiency. In this study, $TiO_2$ electrode was fabricated on FTO using screen printing method. Various overlayers were coated on them by dip coating in solution of saturated $Ba(NO_3)_2$, $Mg(NO_3)_2$ and $N_{2}O_{6}Sr$. They reduced the recombination of electrons from photo excited state of Ru dye. The atmospheric plasma treatment was applied to both the $TiO_2$ and each overlayer coated $TiO_2$ surfaces to improve contact ability with dye. We prepared four samples, one sample has bare $TiO_2$ surfaces to improve contact ability with dye. We prepared four samples, one sample has bare $TiO_2$ electrode and the other samples consist of each overlayer coated $TiO_2$ electrodes. We used XRD, FE-SEM, J-V, IPCE and EIS in order to investigate characteristic.