• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 B
• /
• pp.1292-1295
• /
• 2000

In this paper, we proposed a new single-stage single-switch power factor correction(S-4 PFC) converter with output electrical isolation. The configuration of this converter is achieved by combining a fly back circuit and a forward circuit in one power stage. To verify the theoretical analysis of the proposed converter, a design example is given with its Pspice simu-lation and experimental results.

• 조명전기설비학회논문지
• /
• 제14권3호
• /
• pp.6-14
• /
• 2000

고효율 다중공진형 컨버터는 스위칭 손질을 다중공진 회로를 이용하여 감소시킬 수 있기 때운에 고주파에서 동작이 가능하다. 이려한 고주파 스위칭 동작은 컨버터에 높은 전력 밀도를 제공한다. 그러나 공진 스위치애 걸리는 전압 스트레스는 입력전압의 4~5배 정도여서, 높은 정격의 소자를 필요로 하기 때문에 소자의 온-저항으로 인한 전도 손실을 증가시킨다. 본 문에서는 이러한 문제점 해결하기 위해 제안했던 전압 스트레스를 줄일 수 있는 AT 포워드 MRC는 모델링 해석파 이를 이용한 등가 모드 해석을 하였다. AT 포워드 MRC는 2개의 다중 공전 스위치의 동작 순서에 따라 8개의 등가 모델링이 가능하다. 이 컨버터의 동작 원리는 입력 48[V], 출력 5[V]/50[W]의 실험세트와 PSpice 시뮬레이션을 통해 확인되었으며, 측정된 최대 전압 스트레스는 입력전압의 2.9 배인 170[V]였고 최대 효율은 81.66i%로 측정되었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.166-170
• /
• 2003

This paper presents the TTFC(Two Transistor Forward Converter) using Synchronous Rectifier of Compulsory Control-driver. The two transistor forward circuit is used to decrease voltage stress of primary side and the synchronous rectifier is used to reduce current stress of secondary side. Previous synchronous rectifier's MOSFET of TTFC have long dead time This paper presents synchronous rectifier of compulsory control-driver for minimized dead time. This paper compared with diode rectifier, self-driven synchronous rectifier and compulsory control-driver synchronous rectifier of TTFC. The principle of operation, feature and design considerations are illustrated and verified through the experiment with a 200W 100kHz MOSFET based experimental circuit.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 F
• /
• pp.2691-2694
• /
• 1999

The multi-resonant converter(MRC) can reduce the switching losses exiting in a converter, so it is capable of operating at a high frequency. Such a few MHz high frequency application provides a high power density [$W/inch^{3}$]. But the high voltage stress across a switch of the resonant circuit is about 4$\sim$5 times the input voltage, it causes increasing of the conduction loss in MRC. In this paper, the mode analysis for the suggested AT Forward MRC with low voltage stress is discussed. The operational modes of the AT Forward MRC are divided to 8 equivalent modes according to the two switching sequences, Each mode is analyzed over all of the paper.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2010년도 하계학술대회 논문집
• /
• pp.228-229
• /
• 2010

This paper presents an active voltage balancing approach using a forward fly-back power converter. In the proposed balancing scheme, cell with the higher voltage is selected to extract the extra energy and then a proportion of this extracted energy is distributed to other supercapacitors via the proposed circuit. A system structure consisting of five supercapacitors is built up to verify operation of the proposed scheme.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2013년도 추계학술대회 논문집
• /
• pp.13-14
• /
• 2013

Multiple output converters (MOCs) are widely used for applications which require various kinds of the output voltages due to its advantages in cost, volume, and efficiency. However, most of the MOCs developed so far can regulate only one output tightly and require as many secondary windings in the transformer as the number of the outputs. In this paper, a novel Time Division Multiple Control (TDMC) method to regulate all the outputs in high precision is proposed and applied to the double ended forward converter for the multiple battery charger. Additional benefit of the proposed topology is to require only one secondary winding in the transformer for all the outputs. The proposed converter can charge two different kinds of batteries or same kind of batteries in different state of charges (SOCs) by CC/CV mode independently with the even degree of tight regulation, thereby satisfying the ripple requirements for each battery.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 A
• /
• pp.348-350
• /
• 1996

A new reset winding clamped forward converter with transformer voltage feedback technique for power factor correction with a single-switch/single-stage is proposed. The proposed converter gives the good power factor correction, low current harmonic distortions, and tight output voltage regulation. The prototype shows the IEC555-2 requirements are met satisfactorily with nearly unity power factor.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 Proceedings ICPE 01 2001 International Conference on Power Electronics
• /
• pp.198-202
• /
• 2001

This paper presents a novel prototype version of ZCS-PWM forward DC-DC power converter using power MOSFETs which is designed for application specific low voltage large current conversion operation. The soft-switching forward power converter with a high frequency isolated transformer link which can efficiency operate over wide load ranges under two conditions of ZCS as well as active voltage clamped switching is evaluated and discussed on the basis of the simulation and experimental results.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 A
• /
• pp.136-139
• /
• 1997

The active-clamped double forward-flyback converter is studied in this paper. The converter reduces the voltage stress of the switches and decreases switching loss, EMI. The energy stored in the magnetic core is transferred to both the input voltage source and the flyback output. This makes it possible the output circuit of the flyback to operate at CCM without complex control circuit. The MOSFET is used at output stage, which decreases switching loss.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2002년도 전력전자학술대회 논문집
• /
• pp.374-377
• /
• 2002

This paper presents dynamic analyses and control design of the current-mode controlled active-clamp forward-flyback converter. The circuit averaging technique is used to extract the small-signal circuit model for the power stage From the small-signal circuit model of the power stage, the open-loop transfer functions are derived and used for the compensation design. The analysis results are verified using an experimental converter that delivers a 3.3V/10A output from a $40\~60V$ input source.