• 한국정밀공학회지
• /
• 제13권6호
• /
• pp.45-51
• /
• 1996

Silicon wafers are required to be finished under the roughness of nanometer order for the subsequent chip fabrication processes. Recently, the finish grinding techniques have been researched for the improvement of accuracy and surface roughness simultaneously. Among them, the grinding technique using fine abrasive has been known as an easily accessible method. However, the manufacture of the fine grit grinding wheel has been very difficult because of the coherence of the grits. In this paper, the development of the ultrafine grit silica($SiO_2$) grinding wheel by the combination of the binder coating and the vacuum forming techniques is reported. And, the mechanochemical removal effects of the grinding conditions are discussed. Finally, a successful result of Ra O.4nm. Rmax 4nm in the ground surface roughness of a 6 inch silicon wafer was achieved.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 추계학술대회 논문집
• /
• pp.239-242
• /
• 2005

In the roll forming, a flat strip is progressively deformed by feeding it through a series of rotating rolls. There are various layouts for the tube toll-forming stages. The process sequences are as follows: leveling, roll-forming, welding, bead removing, seam annealing, cooling, sizing and cutting. Electric resistance welded(ERW) tubes have been widely used for the machinery parts, especially for hydroformed automotive parts. However conventional ERW tubes do not have a high formability because of hardening of welded portion by rapid cooling. Moreover the decrease in thickness of the welded portion during the grinding of the inner and outer bead may reduce the formability of the tube. In case of applying the tubular parts without grinding the bead, the flow of the fluid can be prevented due to the turbulent flow induced by the inner bead. In attempt to determine the optimal bead grinding amount in the roll forming process, in the present paper, the effects of the removal depth and width of the inner beads on the hydroformability are analyzed by the finite element simulation.

• 한국생산제조학회지
• /
• 제7권2호
• /
• pp.100-107
• /
• 1998

Diamond wheels with fine grains and multi-porous structures are newely trial developed for smoothing and mirror finishing materials. Grinding wheel must have performed both to remove tool marks efficienitly and to contact elastically with curved surfaces, that are employed for ultra precision and high performance grinding of difficult-to materials such as tungsten carbide alloy using tool and die materials, Diamond grains are bonded by a melamine resin to prevent the decrease of machining efficiency due to grain sinking within the bond materials. Also, highly foamed structures are developed to increase the flexibility of the grinding wheel, and to induce self-sharpening by increasing contact pressure between the grinding wheel and workpiece surfaces. In this paper, melamine-bonded diamond wheels try to manufacture, then the forming method of grinding wheel are suggested, and the grinding characteristics of melamine-bonded diamond grinding wheel are also illustrated.

• 한국기계가공학회지
• /
• 제10권3호
• /
• pp.19-27
• /
• 2011

A weaving machine for texture industry uses a lot of needles and the nib of these needles is necessary to be kept with sharp edge. The re-grinding of the needle by a special purpose of the grinding wheel can be selected for achieving this aim. This study focused on the manufacture and performance assessment the special grinding wheel. A forming mold for the grinding wheel was designed and a sintering process for furnace process control was established. Manufactured wheels were tested for determining suitable grade of the wheel. The selection of optimal grinding conditions was achieved by a response surface method and a genetic algorithm.

• 한국기계가공학회지
• /
• 제15권2호
• /
• pp.84-88
• /
• 2016

This study evaluated the structural safety of a heavy-duty integrated machine for grinding wheel forming. Structural analysis was performed to evaluate the structural safety of the base. The base was designed by dividing the single base and detachable base. The analysis conditions were applied to the own weight and the load of component parts. From the structural analysis results, although the stress of the detachable base was decreased, the amount of deformation was increased. If the deformation of the detachable base decreases, it is expected to be safer than the single base.

• 한국재료학회지
• /
• 제17권11호
• /
• pp.606-611
• /
• 2007

This study was conducted to beneficiation of magnesite by dry grinding and air classification. The raw ore was ground in a ball mill and pin mill controlled with grinding time and linear velocity of grinding media and fractionated in an air classifier. Pin mill is more efficient than the ball mill for liberation. As a result, the MgO grade of concentrate was 47.1% with recovery of 51.51% for classified with 3,000rpm of air classifier for ground at 13,000rpm in pin mill.

• 산업식품공학
• /
• 제13권4호
• /
• pp.269-274
• /
• 2009

습식분쇄의 최적조건을 얻고자 부형제 종류, 농도, 습식 분쇄시 rotor speed, bead size, feed rate, 분쇄회수를 달리하여 분쇄한 결과, 부형제로는 gum arabic을 사용하여 5%의 농도로 첨가할 때 가장 좋은 분쇄효과를 나타내었다. Rotor speed를 달리하여 습식분쇄한 결과, rotor speed가 증가할수록 좋은 결과를 나타내어 4,000 rpm에서 가장 우수한 것으로 나타났다. 원료와 직접 부딪혀 분쇄를 하게 되는 bead는 0.4 mm의 크기를 사용하였을 때 가장 작은 사이즈로 분쇄되는 것으로 나타났다. 분쇄가 이루어지는 chamber내에 원료를 공급하는 비율에 따른 결과에서는 40 L/h 의 속도로 공급했을 때 가장 작은 입도분포를 보였다. 분쇄회수에 따른 영향은 횟수에 따라서는 8회 이상으로 분쇄하였을때 0.6 $\mu$m이하의 입도분포가 90% 이상으로 나타나 10회를 분쇄하였을때 가장 좋은 효과를 나타내었다. 연속운전과 비연속운전의 비교에서는 연속운전이 더 효율적이었으며 부형제 종류에 따른 영향은 gum arabic을 첨가하여 분쇄하였을때 가장 우수한 결과를 나타내었다. 따라서 적절한 농도와 종류의 부형제 사용과 rotor speed, bead size, feed rate, 용매와의 혼합비의 최적공정을 수립한 습식 분쇄기술로 초미세액상칼슘의 제조가 가능하였고, 습식분쇄기술을 식품가공기술로 활용할 수 있는 가능성을 확보하였다.

• 대한금속재료학회지
• /
• 제50권5호
• /
• pp.375-381
• /
• 2012

Magnesium prepared by mechanical grinding under $H_2$ (reactive mechanical grinding) with transition elements or oxides showed relatively high hydriding and dehydriding rates when the content of additives was about 20 wt%. Ni was chosen as a transition element to be added. $Fe_2O_3$ was selected as an oxide to be added. Ti was also selected since it was considered to increase the hydriding and dehydriding rates by forming Ti hydride. A sample $Mg-14Ni-3Fe_2O_3-3Ti$ was prepared by reactive mechanical grinding, and its hydrogen storage properties were examined. This sample absorbs 4.02 wt% H for 5 min, and 4.15 wt% H for 10 min, and 4.42 wt% H for 60 min at n = 2. It desorbs 2.46 wt% H for 10 min, 3.98 wt% H for 30 min, and 4.20 wt% H for 60 min at n = 2. The effects of the Ni, $3Fe_2O_3$, and Ti addition, and hydriding-dehydriding cycling were discussed.

• Design & Manufacturing
• /
• 제8권1호
• /
• pp.27-30
• /
• 2014

Alloy tool steel such as SKD11 and SKD61 or high speed tool like SKH51 are used as materials for semiconductor dies. Cavities, curl blocks, pot blocks and housings are made from those materials. To make those parts from alloy tool steel or high speed tool, one utilizes discharge machining, and mechanical machining including machining center, milling, drilling, forming grinding and others. In the process of cutting machining and polishing, the die materials become unsuitable for machining owing to bubbles and foreign substances in them, which hinders production process. Therefore, this study focuses on die material selection criteria, and on analysis and comparison of material characteristics to help companies to solve their problems, make die manufacture less burdensome and extend die life.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.143-147
• /
• 2003

Despite of outstanding optical performance of glass lens, glass lens have not been widely used because of poor productivity and high cost due to manufacturing process i.e. grinding, polishing. However, press-forming method of glass lens overcomes this disadvantage because of mass production. When glass lens is produced by press-forming method using closed die, it is needed that the volume of glass lens preform precisely measured in order to prevent incomplete products and to increase in life of die. The present paper shows the shortcoming of forming process with closed die, and performs FEM simulation of forming process with open die in order to overcome this shortcoming. The design parameter of open die is selected in standard of assembly with optical module and maintenance of optical performance. FEM simulation is carried out with selected parameter of open die and two basic preform. According to distribution of effective strain in glass lens, optical property of glass lens formed at each set of die and preform is compared.