• Textile Coloration and Finishing
• /
• v.1 no.1
• /
• pp.54-62
• /
• 1989

The woven fabric composed of nylon 6 filaments was treated with aqueous solutions (20, 30, 40, 50, 60%) of formic acid at 3$0^{\circ}C$ for 10 minutes under unrestrained condition, and the shrinkage behavior and some kinds of properties were examined. The shrinkages of the constituent yarns and fabric were increased with formic acid concentration, but they were lower than that of the original filaments because of fabric-structural factors. And the shrinkage of the warp was lower than that of the weft because of the residual stress from weaving process. By the restraint forces such as fabric-structural factors and residual stress, the constituent filaments were damaged partially at 60% of formic acid concentration and the degree of damage on the warp was greater than on the weft. And though the fabric count were increased overall, the spacing between the warps was decreased prior to the weft and eliminated nearly at 60% of formic acid concentration. The thickness, tensile strength, elongation, and handle value of fabric were increased overall with formic acid concentration excepting that the tensile strength for both the warp and weft directions and the elongation for the warp direction were decreased instead by the damage of yarns. But the crease recovery was decreased except the case of the weft direction at 60% of formic acid concentration.

• Journal of Microbiology and Biotechnology
• /
• v.19 no.8
• /
• pp.845-850
• /
• 2009

Bioethanol derived from lignocellulosic biomass has the potential to replace gasoline. Cellulose is naturally recalcitrant to enzymatic attack, and it also surrounded by the matrix of xylan and lignin, which enhances the recalcitrance. Therefore, lignocellulosic materials must be pretreated to make the cellulose easily degraded into sugars and further fermented to ethanol. In this work, hydrothermal pretreatment on corn stover at $195^{\circ}C$ for 15 min with and without lower concentration of formic acid was compared in terms of sugar recoveries and ethanol fermentation. For pretreatment with formic acid, the overall glucan recovery was 89% and pretreatment without formic acid yielded the recovery of 94%. Compared with glucan, xylan was more sensitive to the pretreatment condition. The lowest xylan recovery of 55% was obtained after pretreatment with formic acid and the highest of 75% found following pretreatment without formic acid. Toxicity tests of liquor parts showed that there were no inhibitions found for both pretreatment conditions. After simultaneous saccharification and fermentation (SSF) of the pretreated corn stover with Baker's yeast, the highest ethanol yield of 76.5% of the theoretical was observed from corn stover pretreated at $195^{\circ}C$ for 15 min with formic acid.

• Korean Chemical Engineering Research
• /
• v.61 no.4
• /
• pp.561-569
• /
• 2023

Furfural is a platform chemical that is produced from xylose, one of the hemicellulose components of lignocellulosic biomass. Furfural can be used as an important feedstock for phenolic compounds or biofuels. In this study, we compared and optimized the conditions for producing furfural from xylose in a batch system using two types of catalysts: sulfuric acid, which is commonly used in the furfural production process, and formic acid, which is an environmentally friendly catalyst. We investigated the effects of xylose initial concentration (10 g/L~100 g/L), reaction temperature (140~200 ℃), sulfuric acid catalyst (1~3 wt%), formic acid catalyst (5~10 wt%), and reaction time on the furfural yield. The optimal conditions according to the type of catalyst were as follows. For sulfuric acid catalyst, 3 wt% of catalyst concentration, 50 g/L of xylose initial concentration, 180 ℃ of temperature, and 10min of reaction time resulted in a maximum furfural yield of 59.0%. For formic acid catalyst, 5 wt% of catalyst concentration, 50 g/L of xylose initial concentration, 180 ℃ of temperature, and 150 min of reaction time resulted in a furfural yield of 65.3%.

• Korean Journal of Soil Science and Fertilizer
• /
• v.25 no.4
• /
• pp.407-410
• /
• 1992

Changes in the concentrations of six low-molecular-weight organic acids extracted from hydrolysates of plant residues undergoing decomposition for 90 days under the laboratory condition were investigated. 1. Litters of deciduous and coniferous trees and wild grass cuttings were sampled for the study and concentrations of formic, acetic, succinic, tartaric, malic and citric acids were determined. The concentration of malic acid were negligible. 2. In the wild grass cuttings, the total concentration of low-molecular-weight organic acids decreased with the passage of decomposition. Monocarboxylic acids, I. e., formic and acetic acids, predominated over dicarboxylic and tricarboxylic acids. Formic and acetic acids appeared to be compensatory for each other. Concentration of citric acid increased at a remarkable rate. 3. The total concentration of organic acids in the hydrolysates of deciduous litter was shown to increase. The concentration of monocarboxylic acids was significantly higher in the end of the period of decomposition. Here again a compensatory relationship was observed between concentrations of formic and acetic acids. 4. There was comparatively little change exhibited during the period of experiment concerning the concentrations of organic acids from hydrolysates of decomposing coniferous litter. In contrast with the others, however, the concentration of succinic acid, a dicarboxylic acid, maintained the highest level.

• Asian-Australasian Journal of Animal Sciences
• /
• v.18 no.3
• /
• pp.390-395
• /
• 2005

Reported here are the effects of added formic acid on inhibitory effect of Salmonella gallinarum in poultry feed. Two experiments were conducted to investigate the viability of S. gallinarum and pH of poultry feed using different dietary formic acid levels (0.0, 0.5, 1.0 and 1.5%) on inhibitory effect of S. gallinarum in broiler feed. Experiment one was conducted to investigate the viability of S. gallinarum and pH of artificially contaminated diet at 0, 1, 3, 5 and 7 days after treatment in vitro. Formic acid showed a significant (p<0.05) reduction in the viability for all treatments with time after treatment. Various formic acid levels in vitro showed a reduction in the pH of the diet depending upon the concentration of treated acid, and the diet remained acidic below the growth range of S. gallinarum. This meant that the bacterial cells were exposed to stressful conditions that made them unable to grow. Experiment two was conducted to find out the effect of dietary formic acid levels on S. gallinarum colonization and pH in the contents of crop, small intestine, large intestine and ceca and mortality rate of broiler chicks at 7, 14 and 21 days of age when fed artificially contaminated diet with S. gallinarum. The numbers of S. gallinarum re-isolated from all treated groups except in groups treated with 0.5% formic acid, decreased significantly (p<0.05) compared with the control group. The treatment significantly (p<0.05) lowered the pH of the crop, small intestine, large intestine and ceca contents in all groups except the groups treated with 0.5% formic acid compared with the control. All treated groups showed a significant (p<0.05) reduction in overall mortality rate during the experimental period (3 to 21 days) compared with the control. The results indicate that addition of formic acid in a total concentration of 1.5% to the diet of newly hatched broiler chicks significantly decreases the contamination of diet with S. gallinarum.

• Journal of the Korean Chemical Society
• /
• v.4 no.1
• /
• pp.70-77
• /
• 1957

4,5-Diphenyl Imidazolone is synthesized from Benzoin, Urea, and Acetic acid catalyser. Nowadays, it is being used as an optical bleaching agent for wool and nylon textiles. Up to now, only one process of synthesis has been known. In order to find out the best conditions governing the yield were examined under various catalysers and conditions. In this experiment, the summary of results were as follows. a. On Acetic acid catalyser. The maximum yield conditions were mol ratio (Benzoin: Urea: Acetic acid) 1 : 2 : 14, Acetic acid concentration 99.9%. Reaction temperature 115$^{\circ}$. Under reaction time of 2 hours, above yield was 96.4%. b. On Mineral acid Catalyser. In using of Sulfonic acid, the color of solution was changed dark purlish black. With other mineral acid catalysers, in spite of increasing of temperature, it was proved that Benzoin floats on the solution, so that this reaction could not be continue. c. On Phosphoric acid catalyser. It was made clear that it can not be used for this reaction. d. On Sodium hydroxide catalyser. As one of Alkali catalyser, Sodium hydroxide was examined but this was unsuitable substance for this reaction. e. On Formic acid catalysers. The maximum yield conditions were mol ratio (Benzoin: Urea: Formic acid) 1: 2: 30. Formic acid concentration 85.%. Reaction temperature 150∼110$^{\circ}$. Under reaction time of 90 minutes, the best yield was 87%. Hereby, it was proved that organic acids such as Acetic acid and Formic acid can be used. When using Acetic acid, the yield was better than Formic acid, but it takes longer reaction time than Formic acid. About the fluorescent effect, the temperature of dye-bath must not be over 904,5-Diphenyl Imidazolone is synthesized from Benzoin, Urea, and Acetic acid catalyser. Nowadays, it is being used as an optical bleaching agent for wool and nylon textiles. Up to now, only one process of synthesis has been known. In order to find out the best conditions governing the yield were examined under various catalysers and conditions. In this experiment, the summary of results were as follows. a. On Acetic acid catalyser. The maximum yield conditions were mol ratio (Benzoin: Urea: Acetic acid) 1 : 2 : 14, Acetic acid concentration 99.9%. Reaction temperature 115$^{\circ}$. Under reaction time of 2 hours, above yield was 96.4%. b. On Mineral acid Catalyser. In using of Sulfonic acid, the color of solution was changed dark purlish black. With other mineral acid catalysers, in spite of increasing of temperature, it was proved that Benzoin floats on the solution, so that this reaction could not be continue. c. On Phosphoric acid catalyser. It was made clear that it can not be used for this reaction. d. On Sodium hydroxide catalyser. As one of Alkali catalyser, Sodium hydroxide was examined but this was unsuitable substance for this reaction. e. On Formic acid catalysers. The maximum yield conditions were mol ratio (Benzoin: Urea: Formic acid) 1: 2: 30. Formic acid concentration 85.%. Reaction temperature 150∼110$^{\circ}$. Under reaction time of 90 minutes, the best yield was 87%. Hereby, it was proved that organic acids such as Acetic acid and Formic acid can be used. When using Acetic acid, the yield was better than Formic acid, but it takes longer reaction time than Formic acid. About the fluorescent effect, the temperature of dye-bath must not be over 90$^{\circ}$. and the ratio of 4,5-Diphenyl Imidazolone and water should be from 1:50000. to 1:10000. It proved that the best effect on textiles, and the best condition were dye-temperature near 704,5-Diphenyl Imidazolone is synthesized from Benzoin, Urea, and Acetic acid catalyser. Nowadays, it is being used as an optical bleaching agent for wool and nylon textiles. Up to now, only one process of synthesis has been known. In order to find out the best conditions governing the yield were examined under various catalysers and conditions. In this experiment, the summary of results were as follows. a. On Acetic acid catalyser. The maximum yield conditions were mol ratio (Benzoin: Urea: Acetic acid) 1 : 2 : 14, Acetic acid concentration 99.9%. Reaction temperature 115$^{\circ}C$. . Under reaction time of 2 hours, above yield was 96.4%. b. On Mineral acid Catalyser. In using of Sulfonic acid, the color of solution was changed dark purlish black. With other mineral acid catalysers, in spite of increasing of temperature, it was proved that Benzoin floats on the solution, so that this reaction could not be continue. c. On Phosphoric acid catalyser. It was made clear that it can not be used for this reaction. d. On Sodium hydroxide catalyser. As one of Alkali catalyser, Sodium hydroxide was examined but this was unsuitable substance for this reaction. e. On Formic acid catalysers. The maximum yield conditions were mol ratio (Benzoin: Urea: Formic acid) 1: 2: 30. Formic acid concentration 85%. Reaction temperature 150∼110$^{\circ}C$. Under reaction time of 90 minutes, the best yield was 87%. Hereby, it was proved that organic acids such as Acetic acid and Formic acid can be used. When using Acetic acid, the yield was better than Formic acid, but it takes longer reaction time than Formic acid. About the fluorescent effect, the temperature of dye-bath must not be over 90$^{\circ}C$. and the ratio of 4,5-Diphenyl Imidazolone and water should be from 1:50000. to 1:10000. It proved that the best effect on textiles, and the best condition were dye-temperature near 70$^{\circ}C$. and dye-time 15 minutes. . and dye-time 15 minutes. . and the ratio of 4,5-Diphenyl Imidazolone and water should be from 1:50000. to 1:10000. It proved that the best effect on textiles, and the best condition were dye-temperature near 70$^{\circ}C$. and dye-time 15 minutes.

• Journal of the Korean Institute of Gas
• /
• v.19 no.3
• /
• pp.18-24
• /
• 2015

The flash point is one of the most important indicators of the flammabiliy of liquid solutions. The flash point is the lowest temperature at which there is enough concentration of flammable vapor to form an ignitable mixture with air. In this study the flash points of binary flammable solutions, 2-propanol+propionic acid and n-hexanol+formic acid systems, were measured using Seta flash closed cup tester. Particularly n-hexanol+formic acid system exhibited minimum flash point behavior. The measured values were compared with the calculated values using Raoult's law and optimization method. The calculated data by optimization method described the measured values more effectively than those calculated by Raoult's law.

• Korean Chemical Engineering Research
• /
• v.47 no.3
• /
• pp.362-367
• /
• 2009

Recently, the use of formic acid as a fuel for direct liquid fuel cells has emerged as a promising alternative to methanol. In the work presented herein, we evaluated direct formic acid fuel cells(DFAFCs) with various components under operating conditions, for example, the thickness of the proton exchange membrane, concentration of formic acid, gas diffusion layer, and commercial catalyst. The thickness of the proton exchange membrane influenced performance related to the fuel cross-over. To optimize the cell performance, we investigated on the proper concentration of formic acid and catalyst for the formic acid oxidation. Consequently, membrance-electrode assembly(MEA) consisted of $Nafion^{(R)}$-115 and the Pt-Ru black as a anode catalyst showed the maximum performance. This performance was superior to the DMFCs' one.

• Journal of Korean Society on Water Environment
• /
• v.31 no.5
• /
• pp.468-475
• /
• 2015

Various methods to degrade explosives efficiently in natural soil and water that include trinitrotoluene (TNT) have been studied. In this study, TNT in water was degraded by reduction with palladium (Pd) catalyst impregnated onto alumina (henceforth Pd-Al catalyst) and formic acid. The degradation of TNT was faster when the temperature of water was high, and the initial TNT concentration, pH, and ion concentration in water were low. The amounts of Pd-Al catalyst and formic acid were also important for TNT degradation in water. According to the experimental results, the degradation constant of TNT with unit mass of Pd-Al catalyst was $8.37min^{-1}g^{-1}$. The degradation constant of TNT was higher than the results of previous studies which used zero valent iron. 2,6-diamino-4-nitrotoluene and 2-amino-4,6-dinitrotoluene were detected as by-products of TNT degradation showing that TNT was reduced. The by-products of TNT were also completely degraded after reaction when both Pd-Al catalyst and formic acid existed. Even though there are several challenges of Pd-Al catalyst (e.g., deactivation, poisoning, leaching, etc.), the results of this study show that TNT degradation by Pd-Al catalyst and formic acid is a promising technique to remediate explosive contaminated water and soil.

• Mass Spectrometry Letters
• /
• v.14 no.2
• /
• pp.48-55
• /
• 2023

This study compares the efficiency of weak acid hydrolysis (WAH) using formic acid (FA) and hydrochloric acid (HCl) in the analysis of myoglobin peptides. WAH using 2% and 5% formic acid resulted in the identification of 32 peptides, with varying degrees of cleavage at the C-terminus of aspartic acid residues. HCl WAH with different concentrations demonstrated an increase in the total number of identified peptides but a decrease in fully cleaved peptides as the HCl concentration increased. Notably, deamidation was observed during HCl WAH but not in FA WAH. The addition of HCl WAH after FA WAH provided a similar pattern to HCl WAH, with slightly higher levels of hydrolysis. These findings highlight distinct cleavage patterns and deamidation effects between FA and HCl in the context of WAH.