• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.7
• /
• pp.1349-1355
• /
• 2009

This paper is studied on a novel power factor correction (PFC) AC-DC converter of high efficiency by soft switching technique. The input current waveform in the proposed converter is got to be a sinusoidal form composed of many a discontinuous pulse in proportion to the magnitude of a ac input voltage under the constant switching frequency. Therefore, the input power factor is nearly unity and the control method is simple. The proposed converter adding an electric isolation operates with a discontinuous current mode (DCM) of the reactor in order to obtain some merits of simpler control, such as fixed switching frequency, without synchronization control circuit used in continuous current mode (CCM). To achieve the soft switching (ZCS or ZVS) of control devices, the converter is constructed with a new loss-less snubber for a partial resonant circuit. It is that the switching losses are very low and the efficiency of the converter is high, Particularly, the stored energy in a loss-less snubber capacitor recovers into input side and increases input current from a resonant operation. The result is that the input power factor of the proposed converter is higher than that of a conventional PFC converter. This paper deals mainly with the circuit operations, theoretical, simulated and experimental results of the proposed PFC AC-DC converter in comparison with a conventional PFC AC-DC converter.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.54 no.12
• /
• pp.622-628
• /
• 2005

This paper is given a full detail of mathematical analyses of input current and output voltage for a novel active type power factor correction (PFC) converter. These are compared with harmonics components of input current for a conventional PFC converter. The proposed PFC converter is constructed in using a new loss-less snubber circuit to achieve a soft switching of control device. Also the proposed converter for discontinuous conduction mode (DCM) eliminates the complicated circuit control requirement and reduces the size of components. The input current waveform in the proposed converter is got to be a sinusoidal form of discontinuous pulse in proportion to magnitude of ac input voltage under the constant duty cycle switching. Therefore, input power factor is nearly unity and the control method is simple. Particularly, the stored energy of loss-less snubber capacitor is recovered with input side and increases input current from resonant operation. The result is that input power factor of the proposed converter is higher than that of conventional PFC converter. Some simulative results on computer and experimental results are included to confirm the validity of the analytical results.

• Archives of design research
• /
• v.6 no.1
• /
• pp.47-72
• /
• 1993

Nowadays conmpetltlOn of developing new products is getting keen. We can notice that the role and importance of design are emphasized more than ever.The main cause of this tendency is that technical power is no more a factor which secures the superiority in products competition, as technology is gneneralized in the world. Therefore, design is recognized intensely as a competitive strategy to promote competitive power of products. It is an already known fact that the design for both rational function and charming form to satisfy consumer's desires is a short cut to success, when a company develops a new product to promote competitive power in market. The design which plays a leading role in the activity of developing more cnovenient, more economical and more aesthetic products is called 'Competitive Edge' or 'New Corporate Weapon'. Judging form each company's case of developing products, we can guess that it has its own plan and process of developing new products with defferdnl interest and effort. The strategy of developing products is considered as the most important factor that affects the very existence of rhe company. This thesis is composed of six chapters in all. In the firstchapter, I describe the purpose, method, and scope of study.The second chapter includes the image of form in oil fan heater market in nearby Japan and that of interior in our domestic home and shops, and the trend of word life cycle by analyzing circumstances. The third chapter focuses on consumer's attitude. In the fourth chapter, I compare and test current products of competitive companies including Samsung, Daewoo, Shinilwith those of Gold STar. The trend of products, technique, and design which resulted form this comparison is described. In the fifth chapter I explain the strategy, and process of design of oil fan heater in 1992. The last conclusive chapter presents the major point drawed form the case study, but not includes an estimation of products and the condition of market. In this thesis, I reconsider the general understanding of design and designing process and the value of design as a main factor in the strategy of management by investigating the development of products and the strategy of design, and the process of design.

• Asia-Pacific Journal of Business
• /
• v.11 no.4
• /
• pp.1-19
• /
• 2020

Purpose - This study analyzes the intertemporal patterns in personnel decisions made between a supervisor and a subordinate to understand potential supervisor bias in the decisions. A correlation between the current and the most recent personnel decisions made for a subordinate by a current supervisor captures certain relationship-embedded and time-invariant factors in effect. The characteristics speak to the nature of a supervisor bias arising from a relationship, or favoritism. Design/methodology/approach - This study manually collects the executive profile data from annual reports of key Samsung Group affiliates and compile a longitudinal sample of 3,675 executive-years. It mainly explores the logistic regression analysis. Findings - The study finds that a supervisor' previous promotion award to a subordinate does not improve but decreases the likelihood of promotions in ensuing years, suggesting the containment of favoritism; and that the time since the last promotion award to a subordinate by the current supervisor increases the likelihood of both promotions and dismissals of the subordinate. Research implications or Originality - The findings are generally consistent with the theory suggesting that incentive schemes that align interests between an individual and an organization will contain the form of a supervisor bias.

• Journal of the Korean institute of surface engineering
• /
• v.42 no.5
• /
• pp.191-196
• /
• 2009

Nanocrystalline Cu thin films were electrodeposited from sulfate baths and investigated systematically the influences of $Cu^{2+}$ concentration and additives on current efficiency, residual stress, surface morphology, and XRD patterns of electrodeposited Cu film. Current efficiency was nearly 100% at from 0.2M to 1.0 M $Cu^{2+}$ concentration. but it was linearly increased with $Cu^{2+}$ concentration at less than 0.2M. The residual stress was observed in range of 7.9 to 18.4 MPa and tensile stress mode. Dendritic and powdered form was obtained at below 0.1 M. As increased with $Cu^{2+}$ concentration in solution, the main peak in the XRD pattern shifted (111) and (220) from (200). In the other hand, all about 100% current efficiency observed in all additive concentration systems, and residual stress observed in range of 20.4 to 26.3 MPa tensile stress. The condition 5(Ultra make-up - 10 ml/l, Ulta A - 0.5ml/l, Ultr B - 0.5 ml/l) was good surface morphology, and fcc(111) peak in XRD patterns increased with increasing additive concentration.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.10
• /
• pp.1888-1894
• /
• 2011

In this study, large-current (75 - 400 A), high-voltage (500 - 1000 $V_{rms}$), reliable capacitors with capacitances (C) of 100 - 1000 nF were developed for energy storage facility applications. Mica was used as the dielectric of the capacitors. In order to form a parallel stack of a capacitor element, 50 ${\mu}m$ thick mica sheets with a size of $30mm{\times}35mm$ were used with lead foils for the plate lead type of mica capacitors (HCM-L), while the same sizes of mica sheets coated by Ag paste were employed with lead foils for the parallel plate terminal type (HCM-C). The developed capacitors exhibited well behaviored device characteristics which meet the requirements of the capacitors. The developed capacitors also showed excellent characteristics for thermal shock test. The stability characteristics of developed capacitors for large current stress was superior to those measured for the capacitors prepared recently by CDETm.

• Korean Journal of Materials Research
• /
• v.30 no.12
• /
• pp.672-677
• /
• 2020

Expensive PCBN or ceramic cutting tools are used for the processing of difficult-to-cut materials such as Ti and Ni alloy materials. These tools have a problem of breaking easily due to their high hardness but low fracture toughness. To solve this problem, cutting tools that form various coating layers are used in low-cost WC-Co hard material tools, and researches on various tool materials are being conducted. In this study, WC-5, 10, and 15 wt%Ni hard materials for difficult-to-cut cutting materials are densified using horizontal ball milled WC-Ni powders and pulsed current activated sintering method (PCAS method). Each PCASed WC-Ni hard materials are almost completely dense, with a relative density of up to 99.7 ~ 99.9 %, after the simultaneous application of pressure of 60 MPa and electric current for 2 min; process involves almost no change in the grain size. The average grain sizes of WC and Ni for WC-5, 10, and 15 wt%Ni hard materials are about 1.09 ~ 1.29 and 0.31 ~ 0.51 µm, respectively. Vickers hardness and fracture toughness of WC-5, 10, and 15 wt%Ni hard materials are about 1,923 ~ 1,788 kg/mm2 and 13.2 ~ 14.3 MPa.m1/2, respectively. Microstructure and phase analyses of PCASed WC-Ni hard materials are performed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.255-256
• /
• 2006

The electrical properties of viologen ($VC_8SH$) were studied in terms of the tunneling current characteristics using self-assembling techniques and ultra high vacuum scanning tunneling microscopy (UHV-STM). We fabricated the Au substrate were deposited by thermal evaporation system($420^{\circ}C$). Self-assembled monolayers (SAMs) were prepared on Au(111), which had been thermally deposited onto freshly cleaved, heated mica. The Au substrate was exposed to a 1 mM/L solution of Octanethiol in ethanol for 24 h to form a monolayer. After through rinsing the sample, it was exposed to a 0.1 mM/L solution of $VC_8SH$ in ethanol for 30 min. We measurement of the morphology on the single viologen molecule. The current-voltage (I-V) properties were measured at arbitary configured points on the surface of the sample by using a STS.

• Journal of Welding and Joining
• /
• v.11 no.2
• /
• pp.74-85
• /
• 1993

Effect of Si metal powders addition with the plasma transferred arc(PTA) overlaying process on characteristics of the alloyed layer in aluminum alloy(A5083) has been investigated. The overlaying conditions were 175-250A in plasma arc current, 500mm/min in travel speed, the 5-20g/min in powder feeding rate. Main results obtained are summarized as follows. 1)Sufficient size of molten pool on surface of base metal was required for forming an alloyed layer; in a fixed travel, the formation of alloyed layer with clear and beautiful surface depend upon the plasma arc current and powder feeding rate; the greater plasma arc current and the smaller powder feeding rate were, the better bead was formed. Optimum alloyed conditions by which an excellent alloyed bead obtained was 225A in plasma arc current. PTA process made it possible to form an alloyed layer with up to 67wt% Si. 2)Microstructure in the alloyed layer was in accord with prediction from the Al-Si phase diagram 3)The hardness of the alloyed layer increased in proportion to Si content. 4)As volume fraction of primary Si increased, the specific wearness of the alloyed layer was significantly improved. However, no further improvement was found when the volume fraction was greater than about 30%. 5)Utilizing the PTA process, a crack free alloyed layer with maximum hardness of about Hv 310 could be obtained.

• Applied Chemistry for Engineering
• /
• v.10 no.8
• /
• pp.1119-1123
• /
• 1999

In this paper, electrorefining of uranium metal was studied to develop pyrometallurgical processing technology in molten salt system. The reaction between uranium metal and $CdCl_2$ was taken about 3 hours and the uranium metal deposits were obtained in the form of dendrite grown on the cathode surface in every electrotransport experiment. The shapes of dendrite were changed according to the applied voltages. Current efficiency was decreased with the increase of current density. Deposition rate was not changed after 6 hours and its maxium was obtained at $100{\sim}150mA/cm^2$ of current density and about 75 rpm of stirring speed, respectively. Also, the current efficiency was increased with decrease of the pitch of spiral groove curved on cathode.