• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.11 s.242
• /
• pp.1534-1541
• /
• 2005

Unlike industrial manipulators, the manipulators mounted on service robots are interacting with humans in various aspects. Therefore, safety has been one of the most important design issues. Many compliant robot arms have been introduced for safety. It is known that passive compliance method has faster response and higher reliability than active ones. In this paper, a new safety mechanism based on passive compliance is proposed. Passive mechanical elements, specifically transmission angle of the 4-bar linkage, springs and shock absorbing modules are incorporated into this safety mechanism. This mechanism works only when the robot arm exerts contact force much more than the human pain tolerance. Validity of this mechanism is verified by simulations and experiments. It is shown that the manipulator using this mechanism provides higher performance and safety than those using other passive compliance mechanisms or active methods.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.5
• /
• pp.2031-2037
• /
• 2011

The French doors have the advantage that they can use inner space more efficiently due to without of partition between two rooms. However, when they are used for refrigerators, the door gaskets for sealing may cause interference of themselves during opening and closing, which causes fatal effect on sealing by worn out of the gaskets as well as increases door opening force. This research proposes a new mechanism for the French doors using the parallelogram motion of 4-bar linkage mechanism, which does not make any interference between gaskets. We manufactured the French doors of proposed mechanism to verify that they do not cause any interference during opening and closing, as well as opening force is decreased. The use of our developed mechanism is not limited to refrigerators, but can be extended to other industrial products with the French doors.

• Journal of Aerospace System Engineering
• /
• v.6 no.3
• /
• pp.24-28
• /
• 2012

An actuator should be added to a existing control linkage to make manned aircraft to unmanned. But it is quiet difficult to synchronize actuator with control surface because non-linear error necessarily occurs when four-bar linkage acts in three dimensional motion. In addition, in point of controller design view, while a real-time model needs the control surface deflection as its input, controller needs the actuator command as its output. Hence, the relation between both should be investigated. In this paper, the mathematical relation between actuator and control surface deflection investigated by kinematic analysis of a plant aircraft. The performance margin of the selected actuator also was verified.

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.5
• /
• pp.456-462
• /
• 2010

This paper proposes a new planar robotic manipulator using stackable 4-BAR mechanisms for various applications. The proposed manipulator has an advantage that we can separate the driving actuators from a robotic manipulator. By separating actuators from the manipulator, we are able to separate the electrical component such as electrical wiring from the mechanical linkage/joint components in the robotic manipulator. Also, we suggest the kinematic analysis of the proposed manipulator which is composed of input mechanisms, multiple 4-BAR mechanisms and output mechanisms. Finally, we suggest numerical simulations to show the effectiveness of the proposed manipulator.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• v.10 no.2
• /
• pp.21-25
• /
• 2005

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.10a
• /
• pp.271-272
• /
• 2013

• Journal of Magnetics
• /
• v.18 no.3
• /
• pp.255-259
• /
• 2013

In this paper a new coupling method for efficient and simple analysis of single phase induction motor is presented. The circuit representation of both the stator winding and each conducting rotor loop (composed of rotor bar and end ring segment) is used in conjunction with the distribution of magnetic flux linkage instead of inductance matrix. The flux linkage is calculated using air-gap flux density distributions driven by unit currents in the stator windings and rotor bars. The field distribution of one turn of a coil is calculated by FEM and the result is used to calculate total flux linkage by employing a coordinate transformation. The numerical results give good agreement with prior literature. The method is particularly effective in analyzing the effect of the number of rotor bars.

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.9
• /
• pp.833-839
• /
• 2010

In this paper, a novel 1 DOF hand rehabilitation robot is proposed in consideration of ADL training for stroke patients. To perform several ADL trainings, the proposed robot can move the thumb part and the part of 4 fingers simultaneously and realize the full ROM (Range of Motion) in grasp. Based on these characteristics, the proposed robot realizes several types of grasp such as cylindrical grasp, lateral grasp, and pinch grasp by using a passive revolute joint that can change the thumb movement direction. The movement of the thumb is driven by a cable mechanism and the part of 4 fingers is moved by a four-bar linkage mechanism.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.3_1spc
• /
• pp.587-592
• /
• 2013

Until recently, the primary users of wheelchairs were people with lower body disabilities. However, the number of patients recovering from accidents or surgery, as well as the number of elderly people using wheelchairs, is constantly increasing. This study examined the design and manufacture of standing and gait assist wheelchairs that assist temporary gait disturbed patients to take rehabilitation training and elderly people to engage in walking exercise. A kinematic analysis was used to select a drive motor and design a four-bar linkage mechanism for lifting the backrest vertically. Using a multibody dynamic simulation, detailed design was performed taking into consideration the spatial motion and partial interference, and the necessary push force and stroke of the linear actuator were also calculated. To ensure structural safety, the von-Mises equivalent stresses of the upper and lower brackets of the linear actuator were verified through a finite element analysis. The manufactured wheelchair was shown to operate successfully as intended, using the developed controller for the drive motors and linear actuator.

• Journal of the Korean Society of Industry Convergence
• /
• v.16 no.4
• /
• pp.141-145
• /
• 2013

This paper is the development of industrial robotic hand system and the design methods of industrial robot hand that can mimic human fingers motion. In order to overcome problems incurred during the reduction of the mobility, this study focuses on analyzing human hand structure and finger movements from an anatomical point of view. As a result, distinctive features that improve the discovered stability in constraints for range of motion in the fingers is reflected in this design concept. A 4-bar Linkage is used in robot finger structure. Lastly, there were experiments to inspect the developed robot hands performance. The developed robot hand has many potential applications and can be in many different fields.