• Journal of the Korean Applied Science and Technology
• /
• v.21 no.2
• /
• pp.156-163
• /
• 2004

Low foaming scouring agents (LSSA) were prepared by blending of amine salt of dodecylbenzene sulfone, poly (PO-b-EO) glycol, Newpol PP-2000, MJU-100, ethylene glycol and organic solvent. As the results of several tests, LSSA-2 showed good scouring effect, penetrating ability and emulsifiability, and showed not much water pollution. The foaming power of LSSA-2 measured by Ross & Miles method was 11mm foam height immediately after foaming. And the foaming power of LSSA-2 measured by Ross & Clark method were less than 310mm foam height at $30^{\circ}C$, 17mm at $80^{\circ}C$. As a result, LSSA-2 was proved as a good foaming scouring agent.

• Textile Coloration and Finishing
• /
• v.24 no.1
• /
• pp.79-90
• /
• 2012

This study surveys the characteristics of the PU/MWNT foaming film according to foaming conditions. For this purpose, firstly, 16 kinds of PU/MWNT forming films were prepared with 4 kinds of dispersion solutions (IPA/MWNT, DMF/MWNT, MEK/MWNT, and Toluene/MWNT) and 4 kinds of blowing agents (organic I, organic II, capsule, and inorganic). The electrical resistivity of these PU/MWNT foaming films according to the dispersion solutions and blowing agents were analysed and discussed with surface profile and cell morphology of measured by SEM. And secondly, 24 kinds of PU/MWNT foaming films were also prepared with 2 kinds of IPA dispersion solution contents and 3 kinds of blowing agents with variation of the blowing temperatures and film thickness. The physical properties of the PU/MWNT foaming films such as electrical resistivity (surface and volume) and triboelectricity with cell morphology were measured and discused through the quantities of IPA, blowing agent added and also physical conditions(temperature, thickness so on) for establishing optimum foaming conditions with good electrostatic dissipation.

• Polymer(Korea)
• /
• v.24 no.4
• /
• pp.538-544
• /
• 2000

The characteristics of cell growth and foamed cell structures of PP were investigated by a continuous foaming process. The operating parameters were the contents of blowing agent and nucleating agent, nucleating agent contents, die temperatures and die dimensions. The foaming cells grew without collapse at less than 14.5 wt% of blowing agent, isopentane. But the cells were collapsed when the blowing agent content was more than 14.5 wt%. The foam density dramatically decreased when a very small amount of the nucleating agent, 1 wt%, was added. After the nucleating agent was added, the cell's weight plummeted to one-seventh of its previous weight. Stable foam cell structures were formed at the die temperature of 17$0^{\circ}C$. However, the effects of the pressure drop rate on the cell morphology were not serious.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.198-201
• /
• 2001

Porous structures of aluminum foam have been studied by using return aluminum scrap. The apparent foam shape, foam height, density, pore size and their distributions in various section areas of the experimental samples have been investigated. The sample have been cast into metallic mold, using aluminum foam prepared from a precursor based on pure Al ingot and return aluminum scrap mixed with various amounts of 1-2wt% increasing viscosity and foam agent materials. The process provides for flexibility in design of foam structures via relatively easy control over the amount of hydrogen evolution and the drainage processes which occur during foam formation. This is facilitated by manipulating parameters such as the foaming agent, thermal histories during solidification and mix melt viscosities. A metal for producing the foamed are decomposing a foaming agent in a molten metal such that there is an initial and a subsequent expansion due to foaming agent. It has been found that the Al porous foaming with variation amount of 1∼2wt% foam agent and at 2min holding time, which melting temperature has appeared homogeneous pore size at 650∼700$^{\circ}C$. The compression strength were 10-13 kg/min at 125ppi, and increased by higher pore density. The acoustical performance of the panel made with the foamed aluminum is considerably improved; its absorption coefficient shows NRC 0.6-0.8. It has been found that the Al foam is very preferable for the compactness of the thermal system.

• Korean Journal of Agricultural Science
• /
• v.15 no.1
• /
• pp.82-94
• /
• 1988

This study was performed to obtain the basic data which can be applied to use of foaming mortars. The results obtained were summarized as follows ; 1. The lowest water-cement ratios were shown at the mixing ratio of 1 : 1. But, it was gradually increased in poorer mixing ratio and decreased in more addition of foaming agent. The water-cement ratios were decreased up to 1.6-53.1% by mix-foaming type and 4.4-24.1% by pre-foamed type than cement mortar. 2. The highest bulk densities were shown at the mixing ratio of 1 : 1. But, it was gradually decreased in poorer mixing ratio and more addition of foaming agent. The decreasing rates of bulk densities were increased in richer mixing ratio and more addition of foaming agent. 3. The bulk densities were decreased up to 38.8-55.9% by mix-foaming type and 9.7-23.6% by pre-foamed type than cement mortar. 4. The lowest absorption rates were shown at the mixing ratio of 1 : 1. But, it was gradually increased in poorer mixing ratio and more addition of foaming agent. The increasing rates of absorption rates were increased in richer mixing ratio and more addition of foaming agent. 5. Absorption rates when immersed in 72hours were shown up to 3.41-5.85 times greater by mix-foaming type and 1.05-1.55 times greater by pre-foamed type than those of cement mortar. it was significantly higher at the early stage of immersed time than cement mortar. 6. The highest strengths were shown at the mixing ratio of 1 : 1. But, it was gradually decreased in poorer mixing ratio and more addition of foaming agent. The decreasing rates of strengths were increased in poorer mixing ratio and more addition of foaming agent. 7. The strengths were decreased up to 77.0-92.8% by mix-foaming type and 36.7-74.4% by pre-foamed type than cement mortar. 8. The lowest air contents were shown at the mixing ratio of 1 : 1. But, it was gradually increased in poorer mixing ratio and more addition of foaming agent. The increasing rates of air contents were increased in richer mixing ratio and more addition of foaming agent. 9. Air contents were shown up to 26.0-63.8 times greater by mix-foaming type and 5.8-17.7 times greater by pre-foamed type than those of cement mortar. 10. The correlations between bulk density, absorption rate, compressive strength and air content were highly significant. The multiple regression equations of bulk density, absorption rate, compressive strength, tensile strength, bending strength and air content were computed depending on a function of mixing ratio and addition of foaming agent. They were generally highly significant.

• Elastomers and Composites
• /
• v.50 no.1
• /
• pp.13-17
• /
• 2015

A study of the effects of MWCNT as a nucleating agent on the formation reactions of the rigid polyurethane foams (RPUFs) was carried out. Sample PUFs, formulated with grease-type master batch of MWCNT/surfactant, were fabricated by free-rising method. Temperature changes with time during foaming process were measured using a digital thermometer. RPUF foaming process was observed to undergo 2-step processes with temperature inflection around 60 sec after the start of reaction, and then reached slowly the max. temperature. While the max. temperature of neat PUF was measured as ca. $120^{\circ}C$, that of the samples with MWCNT were as higher value as ca. $130^{\circ}C$, and, even the time to reach that temperature was reduced by about 15 sec. Average cell size of PUF samples decreased from 185.1 for the neat PUF to $162.9{\mu}m$ for the sample of 0.01 phr of MWCNT. As the result, it was considered that MWCNT in RPUF foaming process could play a roll both as a nucleating agent and as a catalyst.

• Journal of the Korean Society of Safety
• /
• v.29 no.2
• /
• pp.18-23
• /
• 2014

Foam extinguishing agent is widely used for extinguishing combustible liquid fires. Compared to other foam type extinguishing agents, protein foam has relatively low cost and low toxicity and produces stable foam blanket which is excellent in heat resistance and sealability, despite it has weak fluidity. Therefore the study investigated foaming characteristics followed by various factors affecting the fluidity of the protein foam extinguishing agent. The extinguishing characteristics differentiated by the changes in fluidity were also experimented. Foaming performance was compared by measuring the expansion ratio and the 25% drainage time. Moreover, the 25% drainage time and the extinguishing time was compared. The results showed that the 25% drainage time and the expansion ratio were increased as the pressure of nozzle and the concentration of hydrolyzed protein liquid enlarged. However the foaming and extinguishing performance were not improved when the condition exceeded certain level of pressure and concentration. The fastest fire extinguishing condition was the nozzle pressure 4bar with the 85wt.% of concentration of hydrolyzed protein liquid.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2007.11a
• /
• pp.27-30
• /
• 2007

Recently, use of light-weight panel is increasing in building. Styrofoam sandwich panel is inexpensive and it is excellent in insulation ability and constructability. But styrofoam of panel inside is low ignition point. Consequently, when panel is fired, it is occur in poisonous gas. On the other hand, light-weight foamed concrete is excellent in insulation ability, fire resistance due to inner pore. Properties of light-weight concrete is influenced by foaming agent type. Accordingly, this study investigate in insulation property of according to foaming agent type in order to using light-weight foamed concrete instead of styrofoam. As a results, Non-heating zone temperature of light-weight foamed concrete of using AP, FP are lower than light-weight foamed concrete of using AES. Light-weight foamed concrete of using AES, FP are satisfied with fire performance of two hours at foam ratio 50, 100. Light-weight foamed concrete of using AP is satisfied with fire performance of two hours at AP ratio 0.1, 0.15. Insulation property is better closed pore by made AP, FP than open pore by made AES.

• Applied Chemistry for Engineering
• /
• v.23 no.1
• /
• pp.77-85
• /
• 2012

Production process of the flexible ceramic foamed body through the complexation with the fiberous sepiolite and expanded pearlite was researched. The processing of fibrillation of the inorganic mineral fiber sepiolite is the most important whole processing for manufacturing of the ceramic foamed body consisting of the expanded perlite and sepiolite. The fibrous sepiolite and expanded pearlite are blended and becomes the slurry phase. And this slurry phase is converted to a massive foamed body through the low temperature heat treatment process less than $300^{\circ}C$. The heat-treatment process of the slurry phase composite has to be designed to include the evaporation step of the moisture remaining among the slurry composition, foaming step by the decomposition of the foaming agent, and resolution removal step of the organic material which was added in the composite remained after the foaming step. The heat treatment process should be considered as significant factors in design of total process. As to the condition of heat treatment process and foaming agent, there was the a correlation. An organic type foaming agent like DSS (dioctyl sodium sulfosuccinte) was effective in foaming of the slurry compound consisting of the expanded perlite and sepiolite fiber.

• Elastomers and Composites
• /
• v.36 no.1
• /
• pp.52-60
• /
• 2001

Physical properties of foams depend on the density of foams, Physical properties of base polymers, open ceil contents, and cell structures including the size, size distribution, shape of ceil and the thickness of membrane and strut. The density of foam is affected by raw materials, concentration oi crosslinking agent and blowing agent and process parameters such as processing technique and condition. Ethylene vinyl acetate copolymer(EVA) foam is a crosslinked cellular material. The foaming characteristics and physical properties of EVA foam are affected by decomposition rate of blowing agent. In this study, the decomposition rate of blowing agent and crosslinking rate, foaming characteristics and physical properties of foams were evaluated. The slow decomposition rate of blowing agent results in low density foam, good shock absorption property and uniform cell size distribution compared to the high decomposition rate of blowing agent.