• Journal of International Academy of Physical Therapy Research
• /
• v.11 no.2
• /
• pp.2042-2051
• /
• 2020

Background: Many trials have been conducted the methods and types of intervention of form rollers, but no research has been done yet that mixes the methods and types of intervention. Objectives: To analyze the effects of myofascial release on the improvement of range of motion (ROM), flexibility, pain pressure threshold, and balance. Design: Randomized controlled trial. Methods: All subjects measured ROM, flexibility, pressure pain threshold, and dynamic balance by pre-test. After pre-test, subjects were randomized that static-vibration foam rolling group (n=12), dynamic-vibration foam rolling group (n=12), general foam rolling group (n=12). For the intervention, 3 sets of 90 seconds were applied to each group, and rest time was set to 60 seconds between sets. In the post-test and follow-up test after 10 minutes, all three groups were measured the ROM, flexibility, pressure pain threshold, and dynamic balance. Results: The results of comparing ROM, flexibility, pressure pain thresholds, dynamic balance ability appeared higher significant difference in the pre-post-10 minutes follow up test in comparison between time in the intragroup (P<.001). As a result of comparing the change of pre-post-10 minutes follow up, static vibration foam rolling showed higher significant difference compared to control groups (P<.001). Conclusion: Through this study, when foam rolling is applied within the same intervention time, static foam rolling can be expected to have a better effect than the existing dynamic foam rolling as well as vibration foam roller can expect better effect than general foam rolling.

• Journal of the Society of Naval Architects of Korea
• /
• v.56 no.4
• /
• pp.291-297
• /
• 2019

Polyurethane foam is the most efficient, high-performance insulation material, used for liquefied natural gas carrier (LNGC) insulation. Because LNGC is exposed to sloshing impact load due to ship motion of 6 degrees of freedom, polyurethane foam should be sufficient dynamic properties. The dynamic properties of these polyurethane foam depends on temperature and density. Therefore, this study investigates the dynamic response of polyurethane foam for various temperature($25^{\circ}C$, $-70^{\circ}C$, $-163^{\circ}C$) and density($90kg/m^3$, $113kg/m^3$, $134kg/m^3$, $150kg/m^3$) under drop impact test with impact energy of 20J, 50J, and 80J. For dynamic response was evaluated in terms of peak force, peak displacement, absorb energy, and the mechanical property with minimized density effects. The results show the effect of temperature and density on the polyurethane foam material for the dynamic response.

• Ocean and Polar Research
• /
• v.25 no.3
• /
• pp.269-275
• /
• 2003

Effects of different operating factors including superficial air velocity (SAV), hydraulic residence time (HRT), protein concentration, and foam overflow height on protein removal by a foam fractionator in simulated seawater aquaculture system were investigated. This experiment was conducted on batch and consecutive modes at different combinations of the affecting factors. The foam fractionator had a diameter of 20cm and a height of 120cm and the experiment was conducted with synthetic wastewater. In 5 consecutive trials, protein concentrations in culture tank water decreased faster when the foam fractionator was operated at higher SAVs and lower HRTs. In batch trials, protein removal rates increased with an increase in SAV but decreased with an increase in URT. Higher protein concentrations in the bulk solution resulted in higher protein removal rates. Protein concentrations in the collected foam condensates increased but the foam overflow rates decreased with the increase of foam overflow heights. The results of this experiment indicate that foam fractionation would be an effective way for protein removal in seawater aquaculture systems and the performance of the foam fractionator depends largely on the operating parameters, especially SAV.

• Elastomers and Composites
• /
• v.50 no.2
• /
• pp.81-86
• /
• 2015

In this study, natural rubber latex foam was prepared in order to replace commercialized polyurethane foams as a car seat material. Physical properties of the latex foam were investigated and the light stability was improved. The latex foam was mixed in an aqueous solution state, and the degree of foaming and the accelerator ratios were appropriately controlled. Tensile properties, hysteresis and dynamic mechanical properties of the latex foam were measured to compare with those of polyurethane foams. UV light absorbers and radical scavengers were added for improving light stability of the latex foam. Xenon lamp test was conducted to investigate the effects of the reagents on light stability. Our results revealed that the prepared latex foam including a light absorber with an antioxidant showed excellent light stable performances.

• Computers and Concrete
• /
• v.24 no.1
• /
• pp.1-6
• /
• 2019

Within the scope of this study, the foam solution was prepared by properly mixing sulfonate based foam agent with water. Furthermore, this solution was mixed with the mixture of fine sand, cement, and water to produce foamed concrete. The mixture ratios which are the percentage of foam solution used in foam concrete were chosen as 0, 20, 40 and 60% by vol. After these groups reached 28 days of strength, they were heated to 20, 100, 400 and $700^{\circ}C$ respectively. Afterward, high-temperature effects on the foamed concrete were obtained by employing physical and mechanical properties tests. Additionally, SEM (scanning electron microscope) and EDX (energy-dispersive X-ray spectroscopy) tests were employed to analyze the microstructure, and ${\mu}-CT$ (micro computed tomography) images were used to reconstruct 3-D models of the heat-treated specimens. Then, these models are analyzed to examine the void structures and the changes in these structures due to the high temperatures. The study has shown that the void structures reduce the high-temperature effects and the foam solution could be mixed with concrete up to 40 % by vol. where the high strength of foamed concrete is non-mandatory.

• Journal of Industrial and Engineering Chemistry
• /
• v.68
• /
• pp.99-108
• /
• 2018

An oil-tolerant and salt-resistant aqueous foam system was screened out as a possible lubricant to enable cold heavy oil transportation. The microstructures and viscoelasticity and effects of heavy oil, salt and temperature on the foam stability were investigated and new rheological and drainage models were established. The results indicate the foam with multilayered shells belongs to a special microcellular foam. The viscoelasticity could be neglected due to its low relaxation time. The drainage process can be divided into three stages. The foam with quality of 67.9% maintains great stability at high oil and salt concentrations and appropriate elevated temperature.

• Fibers and Polymers
• /
• v.3 no.4
• /
• pp.159-168
• /
• 2002

Polyurethane foams were produced by using a homogenizer as a mixing equipment. Effects of stirring speed on the foam structure were investigated with SEM observations. Variation of the bubble size, density of the foam, compressive strength, and thermal conductivity were studied. A hybrid foam consisting of polyurethane foam and commercial polystyrene foam is produced. Mechanical and thermal properties of the hybrid foam were compared with those of pure polyurethane foam. Advancement of flow front during mold filling was observed by using a digital camcorder. Four types of mold geometry were used for mold filling experiments. Flow during mold filling was analyzed by using a two-dimensional control volume finite element method. Variation of foam density with respect to time was experimentally measured. Creeping flow, uniform density, uniform conversion, and uniform temperature were assumed for the numerical simulation. It was assumed for the numerical analysis that the cavity has thin planar geometry and the viscosity is constant. The theoretical predictions were compared with the experimental results and showed good agreement.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.10a
• /
• pp.297-300
• /
• 2001

Physical modeling technique is applied to investigate foam generation in molten aluminum. By using room temperature water with specially designed equipment, the effects of stirrer type, fluid viscosity(glycerine added to water) and stirring velocity on foam generation behaviors are intensively analysed The distribution and size of bubbles varied with each process parameters but the most important parameters are stirring velocity and fluid viscosity. The results obtained from physical simulation have been confirmed by actual aluminum foam generation experiment at various process variables.

• Textile Coloration and Finishing
• /
• v.4 no.3
• /
• pp.82-90
• /
• 1992

To optimize the foam dyeing procedures for polyester and polyester/nylon blended non-woven fabrics, the effects of organic solvents and surfactants were investigated by measuring the foam heights and surface tensions of the foam dyeing solution. The results of the experiments can be summarized as follows: 1) Organic solvents and surfactants (sodium lauryl sulphate: SLS) solution lower the surface tension (ST) of the water, but ST lowering rate of SLS solution is greater than that of solvents. For a 0.25% SLS solution, the minimum surface tension was 30.3 dyne/cm, which is nearly the same value for organic solvents. 2) For 0.25% SLS solutions, additional adding of a 4.0% organic solvent makes the foam height (FH) be its maximum. 3) At 0.6 g/ι dye concentration, incorporation of 0.4% SLS makes the surface tension of the foam solution be its minimum. The foam height did not show any trend due to the dye type. 4) The effect of foam stabilizers (sodium alginate (Alg-Na) and hydroxy ethyl cellulose (HEC)) were also investigated. The foam height of the foaming solution with HEC was greater than that with Alg-Na. The foam stability of the foaming solution with Alg-Na was better than that with HEC.

• KSBB Journal
• /
• v.7 no.3
• /
• pp.172-178
• /
• 1992

A simple and effective method has been developed for the immobilization of lipase producing Rhizopus chinensis on polyurethane foam. In this method, the fungal cells with 1, 3 specific lipase in there inside are immobilized within the foam matrix. Four types of commercially available polyurethane foam were tested. The ultimate purpose of the process is to produce low-cost biocatalysts for lipase-catalyzed reactions, which are being increasingly used for industrial applications. Effects of several parameters were studied on the cell loading and the hydrolytic activity of intracellular lipase after acetone drying. These parameters were the type, size, and amount of polyurethane foam. In all the cases, the intracellular lipase activity obtained with the foam was approximately twice greater than that obtained in the absence of the foam.