• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.20 no.6
• /
• pp.573-581
• /
• 1987

The fish meat paste products are rapidly growing in its production. However, the recent prohibition of AF-2 gives a lot of difficulties in the marketing of fish meat paste products manufactured ty the conventional procedures. The present study aims to obtain the optimal conditions for retaining tile quality of the fish meat paste products with long shelf-life on the market. The fried fish meat paste was sealed in the retort pouches and sterilized under the conditions which the Fo value designated to 6. The effects of the sterilization temperature and the diameter of the products on the quality factors such as jelly strength, water holding capacity, texture and in vitro protein digestibility were investigated. The jelly strength and hardness increased as the sterilization temperature increased. On the other hand, there were no differences found in water holding capacity and elasticity. Of the samples, product with diameter of 12mm showed the highest values of jelly strength, hardness, L values and in vitro protein digestibility which sterilized at $124^{\circ}C$. However. tile results of the organoleptic tests showed rather score in the products with diameter of 16 mm than 12 mm which were sterilized at $124^{\circ}C $. From the results described above, it was concluded that the fried fish meat paste products with 16 mm or less in a diameter which were sterilized at higher temperature could keep high quality.

• Tunnel and Underground Space
• /
• v.20 no.5
• /
• pp.352-359
• /
• 2010

Stability of twin tunnels depends on the pillar width and the ground condition. In this study, large scale model tests were conducted for investigating the influence of the pillar width of twin tunnels on their behavior in the regular horizontal jointed rock mass. Jointed rocks was composed of concrete blocks. Pillar width of twin tunnels varied in 0.29D, 0.59D, 0.88D and 1.18D, where D is the tunnel width. During the test, pillar stress, lining stress, tunnel distortion, and ground displacement were measured. Lateral earth pressure coefficient was kept in a constant value 1.0. As a result, it was found that the pillar stress and the displacement of the ground and tunnel were increased by decreasing pillar width. The maximum displacement rate was measured just after the upper excavation in each construction sequence. And the maximum influence position was the right shoulder of the preceeding tunnel at the pillar side. It was also found that for the stability assessment the inner displacement was more critical than the crown displacement. The influence zone was formed at the pillar width 0.59D~0.88D that was smaller than 0.8D~2.0D, which was proposed by experience for a good ground condition. And it would be concluded that horizontal joints could also influence on the stability of the twin tunnels.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.10
• /
• pp.2028-2042
• /
• 1994

Properly defining signal and noise in a self-organizing system like ART(Adaptive Resonance Theory) neural network model raises a number of subtle issues. Pattern context must enter the definition so that input features, treated as irrelevant noise when they are embedded in a given input pattern, may be treated as informative signals when they are embedded in a different input pattern. The ATR automatically self-scales their computational units to embody context and learning dependent definitions of a signal and noise and there is no problem in categorizing input pattern that have features similar in nature. However, when we have imput patterns that have features that are different in size and nature, the use of only one vigilance parameter is not enough to differentiate a signal from noise for a good categorization. For example, if the value fo vigilance parameter is large, then noise may be processed as an informative signal and unnecessary categories are generated: and if the value of vigilance parameter is small, an informative signal may be ignored and treated as noise. Hence it is no easy to achieve a good pattern categorization. To overcome such problems, a Coupled-ART neural network capable of modularized categorization of patterns is proposed. The Coupled-ART has two layer of tightly coupled modules. the upper and the lower. The lower layer processes the global features of a pattern and the structural features, separately in parallel. The upper layer combines the categorized outputs from the lower layer and categorizes the combined output, Hence, due to the modularized categorization of patterns, the Coupled-ART classifies patterns more efficiently than the ART1 model.

• CRM연구
• /
• v.3 no.2
• /
• pp.43-68
• /
• 2010

One of the recent research trends that universities are increasingly adopting the concept of 'customer' and the customer-oriented strategy has urged us to research enterprise-wide CRM strategy adaptable to university administration. As the first step of CRM strategy for university management, we try to validate the difference of CRM strategic factors among university types. Drawing upon both CRM process and customer equity drivers, which have been recognized as core frameworks for CRM strategy, we developed those survey instruments adoptable into university industry, and validated statistically-significant difference among 12 types of university group constructed by the levels of university evaluation and the location of the universities. We collected 261 responses from 177 universities from all over the country and analyzed the data to see the levels of CRM processes consisting of customer acquisition, retention, and expansion, and customer equity drivers consisting of value equity, brand equity, and relationship equity by using multivariate ANOVA(MANOVA). The result confirms the explicit differences of the levels of CRM processes and customer equity drivers between the groups by university evaluation levels(high/middle/low). However, the analysis failed to show the significant differences of those between the group by university locations(the capital/the suburbs/the six megalopolises/other countries). More specifically, the level of activities for customer acquisition and retention of the universities in the higher-graded group are significantly different from those in the lower-graded group from the perspective of CRM process. In terms of customer equity drivers, the levels of both brand equity and relationship equity of the higher-graded group are significantly higher than those of both middle and lower-graded group. In addition, we found that the value equity between the higher and lower-graded groups, and the brand equity between the middle and lower-graded groups are different each other. This study provides an important meaning in that we tried to consider CRM strategy which has been mainly addressed in profit-making industries in terms of non-profit organization context. Our endeavors to develop and validate empirical measurements adoptable to university context could be an academic contribution. In terms of practical meaning, the processes and results of this study might be a guideline to many universities to build their own CRM strategies. According to the research results, those insights could be expressed in several messages. First, we propose to universities that they should plan their own differentiated CRM strategies according to their positions in terms of university evaluation. For example, although it is acceptable that a university in lower-level group might follow the CRM process strategy of the middle-level group universities, it is not a good idea to imitate the customer acquisition and retention activities of the higher-level group universities. Moreover, since this study reported that the level of universities' brand equity is just correlated with the level of university evaluation, it might be pointless for the middle or lower-leveled universities if they just copy their brand equity strategies from those of higher-leveled ones even though such activities are seemingly attractive. Meanwhile, the difference of CRM strategy by university position might provide universities with the direction where they should go for their CRM strategies. For instance, our study implies that the lower-positioned universities should improve all of the customer equity drivers with concerted efforts because their value, brand, and relationship equities are inferior compared with the higher and middle-positioned universities' ones. This also means that they should focus on customer acquisition and expansion initiatives rather than those for customer retention because all of the customer equity drivers could be influenced by the two kinds of CRM processes (KIm and Lee, 2010). Surely specific and detailed action plans for enhancing customer equity drivers should be developed after grasping their customer migration patterns illustrated by the rates of acquisition, retention, upgrade, downgrade, and defection for each customer segment.

• 한국해양학회지
• /
• v.18 no.1
• /
• pp.55-63
• /
• 1983

The study on the periodic and correlation analysis between water temperature and air temperature has beenconducted by oceanographic data obtained from 1923 to 1979 (For 16-51 years) in 6 ststions in the Korean Waters. The periodic and correlation analyses has been examined by method of he Schuster's and the quadratic formula of least squares method, respectively. The results pbtained from the study are as follows; 1. Periodic analysis 1) The yearly difference between max. and mini. fo surface water temperature was 12.77-17.99$^{\circ}C$ (computed value : 11.67-16.64$^{\circ}C$) in offshore waters, and was 15.72-26.33$^{\circ}C$ (computed value : 15.13-25.29$^{\circ}C$) in inshore waters, and that of air temperature was 21.71-28.60$^{\circ}C$ (computed value : 10.50-27.22$^{\circ}C$). 2) The yearly mean of water temperature by station was 11.25-18.78$^{\circ}C$, and that of air temperature was 11.39-16.16$^{\circ}C$. 3) The annual compnent amplitrde of water temperature was 5.72-12.54$^{\circ}C$, and that of air temperature was 10.04-13.49$^{\circ}C$. 4) The semi-annual component amplitude of water temperature was 0.83-1.30$^{\circ}C$, and that of air temperature was 0.72-1.26$^{\circ}C$. 5) The annual component phase of water temperature was 215-228$^{\circ}C$ (max. temperature shall be in the first and in the middle ten days of August) in inshore waters and 138-244$^{\circ}C$ (max. temperature shall be in the first and in the middle ten days of August) in offshore waters, and that of air temperarture was 212-221$^{\circ}C$ (max. temperature shall be in the first and in the middle ten days of July and in the first tin days of August). 6) The semi-annual component phase of water temperature was 87-110$^{\circ}C$ in offshore waters, and 167-212$^{\circ}C$ in inshore waters, and that of air temperature was 156-189$^{\circ}C$. 2. Correlation analyses of water temperature and air temperature before one month. 1) When the water temperature is in rising time, the quadratic constant of correlation formual was the gradual inreasing type ( constant; 0.010-0.026) in offshore waters, and the gradual decreasing or proportional type (constant; -0.020-0.001) in inshore waters. 2) when the water temperature is in descending time, the quadratic constant of correlation formula was the gradual increasing type (constant: 0.012-0.021) 3) the determination coefficient was 0.964-0.992 at rising time and 0.982-0.999 at descending time of water temperature.

• Journal of the Korean Applied Science and Technology
• /
• v.41 no.1
• /
• pp.9-18
• /
• 2024

Smilax china is known for its excellent antimicrobial, antioxidant, and anti-inflammatory properties. As a foundational study for applying the functionality of Smilax china extracts to cosmetics, it is necessory to investigate the concentration-dependent skin permation characteristics of the flavonoids in the extract, namely quercetin, catechin, and naringenin. Therefore, it serves as a crucial method for conducting this basic research on the functional aspects fo Smilax china extracts for cosmetic applications. This investigation focused on examining the percutaneous permeability characteristics of flavonoids originating from Smilax china. Applying Marzulli's definition, the Kp value of quercetin was categorized as "fast" at 0.1 mg/mL and "moderate" at 0.2 and 0.4 mg/mL. Notably, the permeation rate exhibited a decline with increasing concentration. For naringenin, Flux values were 0.69, 1.07, and 1.42 ㎍/hr/cm² at concentrations of 0.1, 0.2, and 0.4 mg/mL, respectively, with corresponding Kp values of 6.95, 5.34, and 3.56. Naringenin's Kp value fell into the "moderate" category across all concentrations, and as observed with quercetin, the permeation rate decreased with higher concentrations. Likewise, for catechin, Flux values were 0.75, 1.09, and 1.66 ㎍/hr/cm², and corresponding Kp values were 7.55, 5.46, and 4.16. Catechin's Kp value was consistently classified as "moderate" across all concentrations. The efficacy of quercetin, catechin, and naringenin, active ingredients in high-performance and anti-inflammatory Smilax china extracts, was found to exhibit skin penetration properties above the average. This confirms their suitability as excellent natural materials for use in functional cosmetics, given their outstanding capabilities in preventing acne and reducing inflammation.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.16 no.4
• /
• pp.305-315
• /
• 1983

A survey was carried out from July to December in 1979 and 1982 for the investigation of oceanographic conditions and phytoplankton in Seogwipo coastal area. Although a peculiar coastal sea water is formed by in flowing of fresh water, this is developed mainly in summer and disappeared or weakened in its strength after November. However, this coastal sea water covers only the surface while in mid and bottom layer open sea water is approached to the coast. Therefore, coastal and open sea water appears simultaneously in narrow sea area. Mean values of nutrient concentrates on surface layer during investigating period were $3.72{\sim}16.34{\mu}g-at/l$ in silicate, $1.98{\sim}5.53{\mu}g-at/l$ in nitrate and $0.34{\sim}0.90{\mu}g-at/l$ in phosphate. These showed slight differences among places but in general coastal side were lower than open sea side. Phosphates which is the lowest in concentrates among nutrients in Seogwipo coastal area shows almost similar value with Jinhae Bay but higher than open sea water around 10 mile south of Seogwipo. In general, seasonal changes of nutrients in investigating period shows a tendency of the lowest in October, increasing in November, and again slight decrease in December. As a phytoplankton fauna, 48 species, 1 variety and 2 breeds of Diatoms, 29 species, 3 varieties and 1 breed fo Dinoflagellates, and 1 species each of Chroococcus and Trichoceratium were found. Monthly predominant species are all neritic: Rhizosolenia sp. and Ceratium sp. in August, Chaetoceros sp., Ceratium sp. and Peridinium sp. in September, Astrionella sp. and Peridinium sp. in October, Astrionella sp., Navicula sp. and Chaetoceros sp. in November Among these, Rhizosolenia alata f. gracillima in August and Astrionella gracillima in November are remarkable predominant.

• Journal of Korean Society for Atmospheric Environment
• /
• v.15 no.2
• /
• pp.89-100
• /
• 1999

The rain water samples were collected at Chunchon and Seoul by using wet only automatic sampler from January 1996 through 1997. The daily base rain water samples collected over than 95% rainy events components, $SO_4^{-2}$, $NO_3^-$, $CI^-$, NH_4^+$, $Ca^{2+}$, $Mg^{2+}$, $Na^+$, and $K^+$, by ion chromatography. In 1996, about 77% of sampled rain water showed below pH 5.6 and the 60% of rain water was lower than pH 5.0. The volume weighted average pH was 4.7 at all sites. In 1997, the volume weighted average pH was 4.6 and 4.9 at Seoul and Chunchon, respectively. Among the rain water samples,, 87% and 55% fo samples showed below than pH 5.6 and 5.0, respectively. The pH value of Chunchon was significantly (p＜0.05) lower than Seoul at the rain samples for less than 20mm rainfall. However conductivity of the rain samples were 20.9$\mu$S/cm for 1996 and 27.7$\mu$S/cm for 1997 at Seoul, and 19.1$\mu$S/cm for 1996 and 14.1$\mu$S/cm for 1997 at Chunchon. $H_2SO_4$ and $HNO_3$ contributed 65.9% and 29.6% of free acidity at Seoul, respectively. The ratio of [$NO_3^-$]/[nss-$SO_4^{-2}$] were 0.43 at Seoul and 0.51 at Chunchon for rain samples for less than 20mm rainfall. The annual wet deposition of $CI^-$, $NO_3^-$, $SO_4^{-2}$, $H^+$M, $Na^+$, NH_4^+$, $K^+$, $Mg^{2+}$, and $Ca^{2+}$, respectively, 568.8kg/$ extrm{km}^2$, 1489.3kg/$\textrm{km}^2$, 3184.8kg/$\textrm{km}^2$, 20.9kg/$\textrm{km}^2$, 249.4kg/$\textrm{km}^2$, 1091.2kg/$\textrm{km}^2$, 189.8kg/ $\textrm{km}^2$, 90.2kg/$\textrm{km}^2$ and 702.4kg/$\textrm{km}^2$ at Seoul for 1996; 656.4kg/$\textrm{km}^2$, 2029.7kg/$\textrm{km}^2$, 3280.7kg/$\textrm{km}^2$, 27.2kg /$\textrm{km}^2$, 229.4kg/$\textrm{km}^2$, 1063.9kg/$\textrm{km}^2$, 106.9kg/$\textrm{km}^2$, 78.2kg/$\textrm{km}^2$, 645.3kg/$\textrm{km}^2$ at Seoul for 1997; 116.9kg/ $\textrm{km}^2$, 983.3kg/$\textrm{km}^2$, 1797.0kg/$\textrm{km}^2$, 21.4kg/$\textrm{km}^2$, 83.2kg/$\textrm{km}^2$, 648.1kg/$\textrm{km}^2$, 78.0kg/$\textrm{km}^2$, 22.2kg/$\textrm{km}^2$, 368.8kg/$\textrm{km}^2$ at chunchon for 1996; 100.2kg/$\textrm{km}^2$, 1077.6kg/$\textrm{km}^2$, 1754.0kg/$\textrm{km}^2$, 13.4kg/$\textrm{km}^2$, 146.0kg/$\textrm{km}^2$, 602.3kg/$\textrm{km}^2$, 88.8kg/$\textrm{km}^2$, 16.2kg/$\textrm{km}^2$ and 206.8kg/$\textrm{km}^2$ at chunchon for 1997.

• Economic and Environmental Geology
• /
• v.25 no.4
• /
• pp.417-433
• /
• 1992

Lead-zinc-copper deposits of the Jeonheung and the Oksan mines around Euiseong area occur as hydrothermal quartz and calcite veins that crosscut Cretaceous sedimentary rocks of the Gyeongsang Basin. The mineralization occurred in three distinct stages (I, II, and III): (I) quartz-sulfides-sulfosalts-hematite mineralization stage; (II) barren quartz-fluorite stage; and (III) barren calcite stage. Stage I ore minerals comprise pyrite, chalcopyrite, sphalerite, galena and Pb-Ag-Bi-Sb sulfosalts. Mineralogies of the two mines are different, and arsenopyrite, pyrrhotite, tetrahedrite and iron-rich (up to 21 mole % FeS) sphalerite are restricted to the Oksan mine. A K-Ar radiometric dating for sericite indicates that the Pb-Zn-Cu deposits of the Euiseong area were formed during late Cretaceous age ($62.3{\pm}2.8Ma$), likely associated with a subvolcanic activity related to the volcanic complex in the nearby Geumseongsan Caldera and the ubiquitous felsite dykes. Stage I mineralization occurred at temperatures between > $380^{\circ}C$ and $240^{\circ}C$ from fluids with salinities between 6.3 and 0.7 equiv. wt. % NaCl. The chalcopyrite deposition occurred mostly at higher temperatures of > $300^{\circ}C$. Fluid inclusion data indicate that the Pb-Zn-Cu ore mineralization resulted from a complex history of boiling, cooling and dilution of ore fluids. The mineralization at Jeonheung resulted mainly from cooling and dilution by an influx of cooler meteoric waters, whereas the mineralization at Oksan was largely due to fluid boiling. Evidence of fluid boiling suggests that pressures decreased from about 210 bars to 80 bars. This corresponds to a depth of about 900 m in a hydrothermal system that changed from lithostatic (closed) toward hydrostatic (open) conditions. Sulfur isotope compositions of sulfide minerals (${\delta}^{34}S=2.9{\sim}9.6$ per mil) indicate that the ${\delta}^{34}S_{{\Sigma}S}$ value of ore fluids was ${\approx}8.6$ per mil. This ${\delta}^{34}S_{{\Sigma}S}$ value is likely consistent with an igneous sulfur mixed with sulfates (?) in surrounding sedimentary rocks. Measured and calculated hydrogen and oxygen isotope values of ore-forming fluids suggest meteoric water dominance, approaching unexchanged meteoric water values. Equilibrium thermodynamic interpretation indicates that the temperature versus $fs_2$ variation of stage I ore fluids differed between the two mines as follows: the $fs_2$ of ore fluids at Jeonheung changed with decreasing temperature constantly near the pyrite-hematite-magnetite sulfidation curve, whereas those at Oksan changed from the pyrite-pyrrhotite sulfidation state towards the pyrite-hematite-magnetite state. The shift in minerals precipitated during stage I also reflects a concomitant $fo_2$ increase, probably due to mixing of ore fluids with cooler, more oxidizing meteoric waters. Thermodynamic consideration of copper solubility suggests that the ore-forming fluids cooled through boiling at Oksan and mixing with less-evolved meteoric waters at Jeonheung, and that this cooling was the main cause of copper deposition through destabilization of copper chloride complexes.

• Journal of Biomedical Engineering Research
• /
• v.6 no.2
• /
• pp.1-8
• /
• 1985

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70$\pm$1.32mmHg/min)compared to CF dialyzers(4.32$\pm$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500, 550, 570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500, 550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100, 300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3, 000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.SpO2 with Plethysmograph.