• Journal of Magnetics
• /
• 제16권1호
• /
• pp.58-63
• /
• 2011

This paper presents design procedures of a transverse flux linear motor (TFLM). The minimum and maximum flux linkage was determined by the simplified equivalent magnetic circuit and estimated average magnetic flux density at the air gap region by considering the shape of applied magnetomotive force (MMF). With this information, the number of turns of each phase winding was calculated based on the amplitude of applied voltage and speed of a mover. The rated current, coil diameter, and winding area were obtained with the aid of an empirical formula for determining the required MMF. The usefulness of the proposed design method for TFLM is verified by the three-dimensional equivalent magnetic circuit network (EMCN) method and the experimental results of prototyped machine.

• 조명전기설비학회논문지
• /
• 제27권10호
• /
• pp.30-40
• /
• 2013

In this study the method based on flux linkage in cell was introduced in calculation of eddy currents by cell method. According to this method eddy current distribution and the loss can be evaluated and since the shielding effectiveness by flux cancelation of eddy current can be analyzed, this method is applicable to design of conductive shield. And also the formula of shielding factor were so deduced as to be applicable to finite-width infinite-length shielding sheets and infinite-length underground cable shield. These formula are adaptable to magnetic materials as well as conductive materials. As the results of calculation in model shields are follows. In case of finite-width infinite-length shielding sheet, shielding effectiveness increases with increasing of conductivity. In case of infinite-length underground cable shield, the effectiveness become higher with increasing of permeability. Especially the effectiveness is very high in materials with both high conductivity and permeability in underground cable shield.

• 전력전자학회논문지
• /
• 제8권2호
• /
• pp.107-115
• /
• 2003

PMSM은 높은 토크 특성과 우수한 전력 밀도, 논은 효율 때문에 산업용 빛 가정용 기기로 널리 사용되고 있다. PMSM의 우수한 제어 수행을 위해서는 회전자 위치의 정확한 정보가 필요하다. 그러나 위치 센서의 가격이 비싸고, 열악한 환경에서 신뢰도가 떨어지기 때문에 최근에는 센서리스 알고리즘에 대한 연구가 많이 진행되고 있다. 본 논문에서는 회전자 위치의 추정을 위해 쇄교 자속의 도함수를 이용한다. 수치적 미분을 행하지 않고 전압 방정식과 측정된 상전류를 이용한 수식적 미분을 통해 쇄교 자속을 구하는 a-$\beta$ 변환과 수식적 미분을 이용한 새로운 센서리스 알고리즘을 제안한다. 제안된 센서리스 속도 제어 알고리즘이 실험을 통해 증명된다.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제4B권2호
• /
• pp.47-53
• /
• 2004

The salient pole rotor type single phase SRM (switched reluctance motor) uses radial and axial direction magnetic flux simultaneously. Therefore, the output power per unit volume is very high and the shaft length is shorter than other types of SRMs with the same output. Furthermore, it can be manufactured with low cost owing to its simple structure and driving circuit. The prototype was designed using the theory of the traditional rotating machine and 3D FEM analysis. On this paper, the experiment apparatus, which includes the fabricated prototype in previous researches, was fabricated to measure the current and voltage of the prototype. Then the flux linkage, inductance and magnetic co-energy were calculated using the experimental results. Finally, the measured magnetic co-energy was compared with the simulated magnetic co-energy.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.65-66
• /
• 2008

This paper proposes a compensating algorithm for the secondary current of the measurement current transformer (CT) that removes the effects of the hysteresis characteristics of the iron-core. The exciting current resulting from the hysteresis characteristics of the core causes an error between the primary current and the secondary current of the CT. The proposed algorithm decomposes the exciting current into the magnetizing current and the core loss current and each of them is estimated. The core loss current is calculated from the secondary voltage and the secondary voltage-core loss current curve. The core flux linkage is calculated and then inserted into the flux-current curve to estimate the magnetizing current. The exciting current at every sampling interval is obtained by summing the core-loss and magnetizing currents and then added to the measured current to compensate the secondary current. The performance of the proposed algorithm is validated under various conditions using EMTP generated data. The test results of the real CT were also included. The results indicate that the proposed algorithm can improve the accuracy of the measurement CT significantly, and thus reduce the size and the cost of the CT.

• 전기학회논문지
• /
• 제66권2호
• /
• pp.447-452
• /
• 2017

The stator phase winding of a linear pulse motor, which is a new type of linear motor, is comprised of two phases and is structurally characterized by a stacking method in which the winding of one phase is laid on top of the winding of another phase. Such a structural characteristic induces a difference in the flux linkage resulting from the flux of each stator phase winding in the same condition. The difference in the induced flux linkage acts as a kind of thrust ripple component in terms of the generated thrust. Thus, in order to maintain consistent thrust force, a method is required to solve the problem caused by the structural singularity. Hence, in this study, we present a technique for reducing the thrust force ripple generated by the stacking of the stator phase windings of a linear pulse motor through the generation of a compensating current reference value of the current controller in order to keep the torque constant. The proposed compensating algorithm is validated by simulations and experimental results.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1992년도 하계학술대회 논문집 B
• /
• pp.1193-1195
• /
• 1992

A control method of constant flux which is one of the vector control of Induction Motor is discussed. We estimate and calculate the secondary flux from the state equations without a sensor for velocity or linkage flux. A design of the flux obserber that minimizes the effect of variation of the secondary resistance is discussed. The compter simulation is compared with the experimental result.

• 한국자동차공학회논문집
• /
• 제6권6호
• /
• pp.267-275
• /
• 1998

In this study, the instantaneous heat flux measurement probe and the linkage system for the measurement of the instantaneous temperature and heat flux of the DI mono cylinder diesel engine were developed, and these were proved to have a good reliability and sensibility. A 3-D FEM model which consist of full piston to accommodate the eccentric bowl in the piston head, was applied for the analysis of the thermal stress and the temperature distribution. The mean heat flux on the piston head was used as boundary condition for the analysis of piston. The analysis showed that thermal stress concentrate on the bowl and inner surface of pin hall.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2000년도 전력전자학술대회 논문집
• /
• pp.697-700
• /
• 2000

This paper introduces a new rotor position estimation algorithm for the SRM based on the magnetizing curves of aligned and unaligned rotor positions. The flux linkage is calculated by the measured data from phase voltage and phase current and the calculated data are used as the input of magnetizing profiles for rotor position detection. Each of the magnetizing profiles consisted of the methods using the neural network and fuzzy algorithm And also the optima phase is selected by phase selector. To demonstrate the promise of this approach the proposed rotor position estimation algorithms are verified by the experiment results or variable spee range.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제1권4호
• /
• pp.399-404
• /
• 2012

In this paper, a stator-separated axial flux-switching hybrid excitation synchronous machine (SSAFHESM) is presented, of which the structure and operational principle are introduced. The magnetic field distribution under different excited currents is analyzed, and some characteristics including flux-linkage, EMF and field control ability are studied by finite element analysis (FEA). Tests are carried out on a 12/10-pole prototype machine to validate the analysis results, and an excellent agreement is obtained.