• Membrane and Water Treatment
• /
• 제12권2호
• /
• pp.65-73
• /
• 2021

Sponge ball cleaning can generate an abrasion effect, which leads to an attractive increasing in both permeate flux and membrane rejection. The aim of this study was to investigate the influence of the daily sponge ball cleaning (SBC) on the performance of different UF cross-flow membrane modules integrated with a bioreactor. Two 1"-membrane modules and one 1/2"-membrane module were tested. The parameters measured and controlled are temperature, pH, viscosity, particle size, dissolved organic carbon (DOC), total suspended solids (TSS), and permeate flux. The permeate flux could be improved by 60%, for some modules, after 11 days of daily sponge ball cleaning at a transmembrane pressure of 350 kPa and a flow velocity of 4 m/s. Rejection values of all tested modules were improved by 10%. The highest permeate flux of 195 L/㎡.h was achieved using a 1"-membrane module with the aid of its negatively charged membrane material and the daily sponge ball cleaning. In addition, the enhancement in the permeate flux caused by daily sponge ball cleaning improved the energy specific demand for all tested modules. The negatively charged membrane showed the lowest energy specific demand of 1.31 kWh/㎥ in combination with the highest flux, which is a very competitive result.

• 한국화재소방학회논문지
• /
• 제14권2호
• /
• pp.33-38
• /
• 2000

전자산업의 공정에서 PCB기판납땜은 괼수적이며 이에 사용하는 Flux내 용제인 IPA(Iso--propyl alcohol)와 메탄올은 인화성과 폭발성이 강한 물질로 화재위험성이 대단히 높다. 또한 메탄올은 유독성물질로 지정되어 있으며, 환경법상 VOC(Volatile Organic Compound : 휘발성유기화합물)규제물질로 지정되어 있어 대체물질 개발이 절실히 요구된다. 이에 기존 Flux특성을 가지고 있으면서 화재위험성은 없고, 휘발성유기화합물 규제물질에는 해당되지 않는 디클로로프로판(Dichloropropane, DCP)를 주성분으로 하여 Flux 특성에 맞는 안정제 및 첨가제를 적정 조성비로 조합하여 용제를 개발하였다. 그 결과 200ppm의 작업환경허용농도를 470 ppm으로 완화시킬 수 있었으며 납땜불량율은 0.083%에서 0%로, 퍼짐성은 85%에서 87%로, 전연저항은 1.0$\times$$10^{12}$$\Omega$에서 6.9$\times$$10^{12}$/$\Omega$으로 기존 Flux보다 우수하였다. 그러므로 Flux의 안정성은 물론 환경안전측면과 품질, 생산성도 향상이 가능함을 확인하였고, 품질 특성시험 및 제품 신뢰성 시험 결과 만족할 만한 곁과를 얻었다.

• 마이크로전자및패키징학회지
• /
• 제28권2호
• /
• pp.45-50
• /
• 2021

Flip chip 제품의 난이도 증가에 따라 solder wetting 및 신뢰성 관점에서 강점을 갖는 flux 소재에 대한 관심이 높아지고 있다. 지용성 flux의 경우 별도의 세정 공정이 없기 때문에 공정 효율화 측면에서 유리하나, 리플로우 공정이후 반응을 마친 잔여물이 잔존하게 되는 경우 Cu migration 및 delamination을 발생시킬 수 있다. 본 연구에서는 저잔사 flux 구현을 위해 신규 resin에 적합한 solvent 및 activator를 변경 하였으며, package 환경에서 non-wet 및 신뢰성 개선 유무를 확인하였다. 저장 안정성 평가를 통해 신규 소재에 대한 안정성을 확보하였으며, boiling point가 상이한 solvent와 activator 2종 적용 및 activator 함량 증대를 통해 non-wet 미 발생 flux 소재를 확보하였다. 해당 소재에 대한 신뢰성 검증 이후 평면 분석 결과 flux residue 기인성 delamination 현상은 발견되지 않았으며, 이를 통해 저잔사 flux에 대한 최종 조성을 확보하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.303-310
• /
• 2002

The bending vibration and thermal flutter instability of spacecraft booms modeled as circular thin-walled beams of closed cross-section and subjected to thermal radiation loading is investigated in this paper. Thermally induced vibration response characteristics of a composite thin walled beam exhibiting the circumferantially uniform system(CUS) configuration are exploited in connection with the structural flapwise bending-lagwise bending coupling resulting from directional properties of fiber reinforced composite materials and from ply stacking sequence. The numerical simulations display deflection time-history as a function of the ply-angle of fibers of the composite materials, damping factor, incident angle of solar heat flux, as well as the boundary of the thermal flutter instability domain. The adaptive control are provided by a system of piezoelectric devices whose sensing and actuating functions are combined and that an bonded or embedded into the host structure.

• 한국주조공학회지
• /
• 제15권5호
• /
• pp.477-482
• /
• 1995

A computer simulation model of various smelting process for melting waste sand was developed by using energy and material balance concept. This model can predict the coal, flux and oxygen consumption and the volume and temperature of off-gas. The major critical variables for smelting process can be explained by using the analysis of energy and material balance. The major conclusions were as follows; 1. The most important variables for smelting process were high post-combustion ratio, high heat transfer efficiency and refractory protection technology. 2. For saving energy in this smelting process, selection of raw materials i.e coal, flux are very important, espacially using of low volatile coal is very profitable. 3. The treatment cost of waste sand is high and environmental restriction is severe, in this reason we must be concerned in the treatment of waste sand by smelting process.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 B
• /
• pp.1043-1045
• /
• 2004

This paper deals with the core loss calculation of a BLDC motor made of Soft Magnetic Composite material. Since the teeth of motor partially have overhang in axial direction, 3 - dimensional equivalent magnetic circuit network (3D-EMCN) is used as an analytical method to get flux density of each element. The total core loss is calculated with the magnetic flux density and core loss curves of the SMC material. The calculated result is compared with core loss of the motor without overhang in stator teeth.

• 한국전기전자재료학회논문지
• /
• 제16권5호
• /
• pp.429-434
• /
• 2003

The magnetic field sensor was fabricated with superconducting ceramics of BiPbSrCaCuO system. The sensor at liquid nitrogen temperature showed the increase of electrical resistance by applying magnetic field. Actually, the voltage drop across the sensor was changed from zero to a value more than 100 $\mu\textrm{V}$ by the applied magnetic field. The change of electrical resistance depended on magnetic field. The sensitivity of this sensor was 2.9 $\Omega$/T. The sensing limit was about 1.5${\times}$10$\^$-5/ T. The increase of electrical resistance by the magnetic field was ascribed to a modification of the Josephson junctions due to the penetrating magnetic flux into the superconducting material. Considering the observed properties of the superconductor with trapped magnetic flux, a magnetic sensor was fabricated to detect simultaneously both the intensity and the direction of the magnetic field.

• 한국산학기술학회논문지
• /
• 제12권3호
• /
• pp.1289-1301
• /
• 2011

본 논문에서는 전 속도 영역에서 안정적인 자속추정이 가능한 유도전동기 자속추정방법을 제안 하였다. 제안된 방법은 전압, 전류, 속도 등의 정보를 통하여 자속각을 연산하는 유도전동기 직접벡터제어방식을 이용하였다. 유도전동기 벡터제어에 있어서 자속정보는 필수적이기 때문에 정확한 자속을 추정하기 위한 방법으로 저속영역에서 는 전류모델 자속 추정기를, 고속영역에서는 전압모델 자속 추정기를 각각 이용함으로써 전 속도영역에서 정확한 자속을 추정할 수 있었다. 또한 기본적인 속도, 전류, 자속제어기는 PI제어기를 이용하였으며, 각각의 적분에 의한 오차를 보상하기 위하여 Anti-windup PI 제어기를 추가하였다. 제시한 제어기의 타당성을 알아보고자 Matlab / simulink를 이용하여 전류모델, 전압모델 자속 추정기를 설계하여 정확한 자속추정이 이루어짐을 확인하였으며, 유도 전동기 벡터제어 시 간접벡터와 직접벡터방식의 파라미터 영향에 따른 분석을 통해 보다 정밀한 제어가 이루어짐을 확인하였다. 이와 같은 시뮬레이션 결과를 분석 하여 제시한 알고리즘의 타당성을 입증하였다.

• Transactions on Electrical and Electronic Materials
• /
• 제6권4호
• /
• pp.159-163
• /
• 2005

We analyzed the fault current limiting characteristics of a flux-lock type $high-T_c$ super­conducting fault current limiter (HTSC-FCL) using series resonance between capacitor for series resonance and magnetic field coil which was installed in coil 3. The capacitor for the series resonance in the flux-lock type HTSC-FCL was inserted in series with the magnetic field coil to apply enough magnetic field into HTSC element, which resulted in higher resistance of HTSC element. However, the impedance of the flux lock type HTSC-FCL has started to decrease since the current of coil 3 exceeded one of coil 2 after a fault accident. The decrease in the impedance of the FCL causes the line current to increase and, if continues, the capacitor for the series resonance to be destructed. To avoid this operation, the flux-lock type HTSC-FCL requires an additional device such as fault current interrupter or control circuit for magnetic field. From the experimental results, we investigated the parameter range where the operation as mentioned above for the designed flux-lock type HTSC-FCL using series resonance occurred.

• Biotechnology and Bioprocess Engineering:BBE
• /
• 제10권1호
• /
• pp.91-98
• /
• 2005

In order to investigate central metabolic changes in Beijerinckia indica, cells were grown on different carbon sources and intracellular flux distributions were studied under varying concentrations of nitrogen. Metabolic fluxes were estimated by combining material balances with extracellular substrate uptake rate, biomass formation rate, and exopolysaccharide (EPS) accumulation rate. Thirty-one metabolic reactions and 30 intracellular metabolites were considered for the flux analysis. The results revealed that most of the carbon source was directed into the Entner-Doudoroff pathway, followed by the recycling of triose-3-phosphate back to Hexose­6-phosphate. The pentose phosphate pathway was operated at a minimal level to supply the precursors for biomass formation. The different metabolic behaviors under varying nitrogen concentrations were observed with flux analysis.