• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.368-373
• /
• 2003

This paper presents a study of low frequencies volume velocity vibration control of a smart panel in order to reduce sound transmission. A distributed piezoelectric quadratically shaped polyvinylidene fluoride (PVDF) polymer film is used as a uniform force actuator and an array of 4$\times$4 accelerometer is used as a volume velocity sensor for the implementation of a single-input single-output con rot system. The theoretical and experimental study of sensor-actuator frequency response function sho vs that this sensor-actuator arrangement provides a required strictly positive real frequency response function below about 900Hz. Direct velocity feedback could therefore be implemented with a limited gain which gives reductions of about 15㏈ in vibration level and about 8 ㏈ in acoustic power level at the (1, 1) mode of the smart Panel. It has been also shown that the shaping error of PVDF actuator could limit he stability and performance of the control system.

• ETRI Journal
• /
• v.35 no.4
• /
• pp.734-737
• /
• 2013

Nonvolatile ferroelectric poly(vinylidene fluoride-co-trifluoroethylene) memory based on an organic thin-film transistor with inkjet-printed dodecyl-substituted thienylenevinylene-thiophene copolymer (PC12TV12T) as the active layer is developed. The memory window is 4.5 V with a gate voltage sweep of -12.5 V to 12.5 V. The field effect mobility, on/off ratio, and gate leakage current are 0.1 $cm^2/Vs$, $10^5$, and $10^{-10}$ A, respectively. Although the retention behaviors should be improved and optimized, the obtained characteristics are very promising for future flexible electronics.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.29-32
• /
• 1999

$GaF_3$ films were directly grown on p' and p-type GaAs(100) substrates using a $SF_6$ plasma discharge system. GaAs MIS(Meta1-Insulator-Semiconductor) capacitor was successfully fabricated for about 1 hour at temperature $290^{\circ}C$ using the as-grown $GaF_3$ films. The as-grown films on p'-GaAs exhibited a current density of less than 6.68 $\times$ $1O^{-9}$ A/$cm^2$ at a breakdown field of 500kV/cm and a refractive index of 2.0 ~ 2.3 at a wavelength of 632.8 nm. The dielectric constant was about 5 derived from 1 MHz capacitance-voltage (C-V) measurements. Dielectric dispersion of the fluoridated films on p'-GaAs measured ranged from 100 Hz to 10 MHz was not observed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.3
• /
• pp.513-519
• /
• 2019

Typically, contaminated sediments cause clogging of the drain pipe, which increases the residual water pressure in the drain pipe; this study constructed a system for improving drainage efficiency of tunnels by reducing physical and chemical obstructions through ultrasonic energy generated by a PVDF film. The developed hybrid drainage system utilized a PVDF material film fused with an existing drainage tunnel and maintenance system resulting in the ability to initialize the reverse piezoelectric effect, which was evaluated through an on site application. In order to investigate the maintenance performance of the tunnel drainage system, contaminated sediments were simulated in a drainage pipe to test the effect of ultrasonic conditions on drainage efficiency in the laboratory. As a result of applying the developed portable equipment, the ultrasonic energy was generated for about 20 minutes resulting in a reduction of 74.62% of the contaminated sediments and improving drainage efficiency. From the tunnel, acoustic pressure measurements were taken to calculate the response rate while taking into account the laboratory results. In addition, PVDF film was attached to the transverse and longitudinal side of the drainage pipes where contaminated sediments occur most often in the field tunnel. these calculations show contaminant removal was 90% effective.

• Applied Chemistry for Engineering
• /
• v.19 no.2
• /
• pp.185-190
• /
• 2008

In order to increase the surface area of electrodes for electrosorption, porous carbon electrodes were fabricated by a wet phase inversion method. A carbon slurry consisting of a mixture of activated carbon powder (ACP), polyvinylidene fluoride (PVdF), and N-methyl-2-pyrrolidone (NMP) as a solvent was cast directly on a graphite sheet. The cast film was then immersed in pure water for phase inversion. The physical and electrochemical properties of the electrodes were investigated using scanning electron microscopy (SEM), porosimetry, and cyclic voltammetry. The SEM images verified that the pores of various sizes were formed uniformly on the electrode surface. The average pore sizes determined for the electrodes fabricated with various NMP contents ranged from 64.2 to 82.4 nm and the size increased as the NMP content increased. All of the voltammograms showed a typical behavior of charging and discharging characteristic at the electric double layer. The electrical capacitance ranged from 3.88 to $5.87F/cm^2$ depending on the NMP contents, and the electrical capacitance increased as the solvent content decreased. The experimental results showed that the solvent content is an important variable controlling pore size and ultimately the capacitance of the electrode.

• Composites Research
• /
• v.18 no.6
• /
• pp.26-33
• /
• 2005

The mechanical properties of composite materials may severely degrade in the presence of damage. Especially, the high-velocity impact such as bird strike, a hailstorm, and a small piece of tire or stone during high taxing, can cause considerable damage to the structures and sub-system in spite of a very small mass. However, it is not easy to detect the damage in composite plates using a single technique or any conventional methods. In this paper, the PVDF(polyvinylidene fluoride) film sensors were used for monitoring high-velocity impact damage initiation and propagation in composite laminates. The WT(wavelet transform) and STFT(short time Fourier transform) are used to decompose the sensor signals. A ultrasonic C-scan and a digital microscope are also used to examine the extent of the damage in each case. This research shows how various sensing techniques, PVDF sensor in particular, can be used to characterize high-velocity impact damage in advanced composite.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.05a
• /
• pp.531-533
• /
• 2013

In this paper, to study the IPMC (Ionic exchange Polymer Metal Composite) material consisting of a sulfonic acid ion and fluoride combination of carbon with Nafion film greatly affected the electro-active polymer (Electro Active Polymer) characteristics and the presence of water and cationshave properties. Use or electrical energy into mechanical energy, mechanical energy, electrical energy, and can be utilized to its characteristics, depending on the water and cations in water varies greatly. Configure the device simulations in order to study the electrical properties of these IPMC. Stepper Motor using MCU and simulator designed for the electrical characterization due to the movement and to the implementation of the mechanical movement of ocean currents. In this study, configuration the IPMC and simulation device to the area of the IPMC to the efficient use of energy currents, frequency, salinity concentration, through the efficient use of the IPMC due to the bend angle of the electrical analysis and research methods we propose.

• Proceedings of the KIEE Conference
• /
• 2001.07e
• /
• pp.35-39
• /
• 2001

The purpose of this paper is improvement the piezoelectric of Polyvinylidene fluoride(PVDF) organic thin films is fabricated by vapor deposition method. The piezoelectric of PVDF organic thin films attributed to dipole orientation in crystalline region. Also, the piezoelectric characteristic reduced that dipole moments orientation in crystalline region interfered with impurity carriers. Therefore, PVDF organic thin films fabricated with high substrate temperature condition for crystallinity improvement. The crystallinity of PVDF organic thin films fabricated by this condition increase from 47 to 67.8%. The ion density of PVDF organic thin films fabricated by substrate temperature variation from $30^{\circ}C$ to $105^{\circ}C$ decreased from $1.62{\times}10^{16}cm^3$ to $6.75{\times}10^{11}cm^3$ when temperature and frequency were $100^{\circ}C$, 10Hz, respectively. The $d_{33}$ and piezo-voltage coefficient of PVDF organic thin films increased from 20pPC/N to 33pC/N and $162.9{\times}10^{-3}V{\cdot}m/N$ to $283.2{\times}10^{-3}V{\cdot}m/N$, respectively. For the sake of the applications of piezoelectric sensor, we analyzed the output voltage characteristic as a function of the distance between an oscillator of 28kHz and PVDF organic thin film transducer. From this, we found that the output voltage is inversely proportional to the distance. At this time, the period was about $35.798{\mu}s$ and equal the oscillator frequency.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.57 no.2
• /
• pp.140-145
• /
• 2008

The purpose of this paper is to discuss the fabrication of $\beta$-PVDF($\beta$-Polyvinylidene fluoride, ${\beta}-PVF_2$) organic thin films using the vapor deposition method. Vapor deposition was performed under the following conditions: the temperature of evaporator, the applied electric field, and the pressure of reaction chamber were $270^{\circ}C$, 142.4 kV/cm, and $2.0{\times}10^{-5}\;Torr$, respectively. The molecular structure of the evaporated organic thin films were evaluated by a FT-IR. The results showed that the characteristic absorption peaks of $\beta$-form crystal increase from 72% to 95.5% with an increase in the substrate temperature. In the analysis of the electric characteristics, the abnormal increases in the relative dielectric constant and the dielectric loss factor in the regions of low frequency and high temperature are known to be caused by inclusion of impurity carriers in the PVDF organic thin films. In order to analyze quantitatively the abnormalities in the conductivity mechanism caused by ionic impurities, the product of the ion density and the mobility that affect the electrical property in polymeric insulators is analyzed. In the case of a specimen produced by varying the substrate temperature from $30^{\circ}C$ to $105^{\circ}C$, the product of mobility and the ion density decreased from $4.626{\times}10^8$ to $8.47{\times}10^7/V{\cdot}cm{\cdot}s$. This result suggests that the higher the substrate temperature is maintained, the better excluded the impurities are, and the more electrically stable material can be obtained.

• Journal of the Korean Chemical Society
• /
• v.57 no.5
• /
• pp.547-553
• /
• 2013

Zirconium oxide ($ZrO_2$) nano porous membranes were fabricated by electrochemical two-step anodization with an electropolished zirconium substrate in inorganic water-based and organic electrolyte systems containing small amounts of fluoride. Using two-step anodization and organic electrolytes, highly regular and ordered nanotubular $ZrO_2$ oxide layers can be compared with aqueous electrolytes. The morphology and size of the nano porous layers were characterized by FE-SEM (field emission scanning electron microscopy), XRD (X-ray diffraction), and EDS (energy dispersive spectroscopy). Luminescence properties were investigated by photoluminescence measurements.