• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.5B
• /
• pp.467-474
• /
• 2011

Debris flow is one of the most hazardous natural processes in mountainous regions. The degradation of discharge capacity of drainage facilities due to debris flows may result in damages of properties and casualty as well as road. Understanding and accurate reproducing flow behaviour of debris flows at various conditions, such as sediment volume concentration and approaching channel and culvert slopes, are prerequisite to develop advanced design criteria for drainage facilities to prevent such damages. We carried out a series of laboratory experiments of debris flows in a rectangular channel of constant width with an abrupt change of bottom slope. The experimental flume consists of an approaching channel part with the bed slope ranging $15^{\circ}$ to $30^{\circ}$ and the test channel with slope ranging from $0^{\circ}$ to $12^{\circ}$ which mimics a typical drainage culvert. The experiments have been conducted for 22 test cases with various flow conditions of channel slopes and sediment volume concentration of debris flows to investigate those effects on the behaviour of debris flows. The results show that, according to sediment volume concentration, the depth of debris flow is approximately 50% to 150% larger than that of fresh water flow at the same flow rate. Experimental results quantitatively present that flow behaviour and deposit history of debris flows in the culvert depend on the slopes of the approaching and drainage channels and sediment volume concentration. Based on the experimental results, furthermore, a logistic model is developed to find the optimized culvert slope which prevents the debris flow from depositing in the culvert.

• Journal of the Korean Geotechnical Society
• /
• v.25 no.4
• /
• pp.91-103
• /
• 2009

Slope failure depends upon the climatic features related to related rainfall, structural geology and geomorphological features as well as the variation of the mechanical behaviors of soil constituting a slope. In this paper, among many variables, effects of soil layer thickness on the slope failure process, and variations of matric suction and volumetric water content were observed. When the soil layer is relatively thick, the descending wetting front decreases matric suction and the observed matric suction reaches to "0" value. When the wetting front reaches to the impermeable boundary, the bottom surface of steel soil box, ascending wetting front was observed. This observation can be postulated to be the effects of various sizes of pores. When macro size pores exist, the capillary effects can be reduced and infilling of pore will be limited. The partially filled pores would be filled with water during the ascending of the wetting front, which bounces from the impermeable boundary. This assumption has been assured from the observation of variation of the volumetric water contents at different depth. When the soil layer is thick (thickness = 20 cm), for granular material, erosion is a cause triggering the slope failure. It has been found that the initiation of erosion occurs when the top soil is fully saturated. Meanwhile, when the soil layer is shallow (thickness = 10 cm), slope slides as en mass. The slope failure for this condition occurs when the wetting front reaches to the interface between the soil layer and steel soil box. As the wetting front approaches to the bottom of soil layer, reduction of shear resistance along the boundary and increase of the unit weight due to the infiltration occur and these produce complex effects on the slope failure processes.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.29 no.6
• /
• pp.363-368
• /
• 2017

The tsunami flood the coastal cities and damage the land structures. The study on wave pressure and force on land structures is one of the important factors in designing the stability of inland structures. In this study, two - dimensional wave flume tests on the horizontal wave force and pressure of tsunamis on a simplified box-type structure was conducted. Vertical distribution and wave power of horizontal wave pressure over time were measured by pressure sensors and force transducer. Also, those were measured from the different wave breaking types. The vertical distribution of horizontal wave pressure was uniform at the moment when the horizontal wave force to the structure was maximum under the breaking wave condition. A surf similarity parameter was employed in order to figure out the relationship between the maximum horizontal wave force on the structure as a function of various incident wave conditions. As a result, the non - dimensionalized horizontal wave force tends to decrease exponentially as the surf similarity parameter increases.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.12
• /
• pp.120-127
• /
• 2016

This study examined the dynamic characteristics of the gate to identify the optimal gate installation direction according to the installation direction. A 1:31 scale model was constructed for a 47.5m prototype gate using acrylic. The scaled weights were tuned by adding lead weights. The first step was to measure the natural frequencies of the model gates, and compare them with finite-element analysis of the prototypes as a calibration. The scaled model was tested in a 1.6 m wide concrete flume for two orientations to determine the effects of the gate orientation on structural vibrations. Vertical vibrations were measured under a range of operational conditions, including a range of bottom opening heights and different upstream and downstream water levels. For large bottom opening heights in the normal direction, relatively large vibrations were induced by vortices shed at the plate bottom that would strike the horizontal truss member. This phenomenon was avoided in the reverse direction. For small bottom opening heights in the normal direction, these vibrations were caused by a suction force that developed at the gate bottom. The gate model in the reverse direction was preferred because of its low overall vibrational response under general gate opening and flow level combinations.

• Journal of Korea Water Resources Association
• /
• v.41 no.9
• /
• pp.863-872
• /
• 2008

In this study, a series of deposition tests have been conducted on saltwater condition(salinity 32 %o) using an annular flume, in order to estimate depositional properties of kaolinite sediments and to analyze the effect of the initial concentration on them. Total 37 deposition tests have been carried out in three different initial concentrations (1000, 5000, 15000 ppm) with varying the bed shear stress. From these test results, minimum shear stress (or critical shear stress for deposition; ${\tau}_{bmin}$) and the deposition rate parameters (${\sigma}_1,\;({\tau}^*_b-1)_{50},\;{\sigma}_2,\;t_{50}$) for kaolinite sediments have been quantified, and the effects of the initial concentration and salinity on depositional properties of cohesive sediments have been analyzed qualitatively. As the results, ${\tau}_{bmin},\;{\sigma}_1\;and\;({\tau}^*_b-1)_{50}$ are found to be 0.147, 0.74 and $0.65N/m^2$ respectively. Through comparing with results from previous studies, the performance of this study and tests results are shown to be good enough to verify.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.22 no.4
• /
• pp.203-214
• /
• 2010

This study numerically investigates the wave control of 2-rowed Impermeable Rectangular Submerged Dike(IRSD) with an object of how to control short-period and solitary waves simultaneously based on the Bragg resonance phenomenon that elevates the wave control performance. The boundary integral method using Green formula and the 3-D one-field Model for immiscible TWO-Phase flows (TWOPM-3D) by 3-D numerical wave flume have been used for the numerical predictions for short-period and solitary waves, respectively. These numerical models were verified through the comparisons with the previously published numerical results by other researchers. Through the parametric tests of numerical experiments for short-period waves, an optimum model of 2-rowed IRSD of a lowest transmission coefficient has been found. Furthermore, the performances of 3-D wave control for solitary waves were evaluated for the various free board, crown widths and gap distance between dikes, and have been compared with those of a single-rowed IRSD. Numerical results show that a 2-rowed IRSD with a less cross sectional area than 1-rowed one improves the wave attenuation performances when it is compared to that of single-rowed IRSD. Within the test frequency ranges of the numerical simulations conducted in this study, 2-rowed IRSD with an optimum gap distance shows an outstanding improvement of the wave attenuation up to 58% compared to that of single-rowed IRSD.

• Journal of the Korean GEO-environmental Society
• /
• v.22 no.2
• /
• pp.25-33
• /
• 2021

This study was conducted to understand the deposition characteristics of debris flow and to analyze the reduction effect of debris flow damage by installing a berm. Flume experiments were performed in consideration of various channel slope and volumetric sediment concontration. In order to analyze the reduction effect of debris flow damage by installing a berm, the cases of not installing a berm and the cases of installing a berm were compared. In this study, the runout distance, total travel distance, and mobility ratio were analyzed among the deposition characteristics of debris flow. First, the deposition characteristics of debris flow according to the change of the channel slope were analyzed, and the deposition characteristics of debris flow due to the change of volumetric sediment concentration were analyzed. In addition, the change rate of debris flow deposition characteristics when a berm was installed was calculated based on the case when a berm was not installed. As a result of the experiments, it was confirmed that the channel slope and volumetric sediment concentration had a significant effect on the deposition characteristics of debris flow. In addition, when a berm is installed on the slope, the runout distance and mobility ratio of debris flow are greatly decreased, and the total travel distance is increased. This means that installing a berm delays the movement of debris flow and reduces the potential mobility of debris flow. The results of this study will provide useful information for understanding the deposition characteristics of debris flow. Furthermore, it is expected to help in the design of a berm.