• 한국유체기계학회 논문집
• /
• 제18권6호
• /
• pp.57-62
• /
• 2015

The test of comparing liquid flow calibration system (approved by KOLAS) for accuracy and structure change test was performed in the test bed in order to evaluate the typical characteristics of the electromagnetic flow meters and parshall flume that are generally used in the water discharging facilities. The results of the accuracy comparing test with liquid flow calibration system showed the error of less than 2%. Pharshall plume got error up to -8.3% (low flow) from the flow rate test, but less than 4% from the accumulated flow test because of offset error at high flow rate and low flow rate. Evaluation of structual change test was tested with only parshall flume using structure and it consisted of installation angle (parshall flume and level sensor) and position change. Installation angle, water level sensor angle and position changing test for parshall flume had errors of 3.1%~-9.2%, 0.4%~-5.6% and 0.2%~1.3% respectively. Especially, the error showed the largest increase when the water level sensor measured the point of decreased flow by the structure change. Therefore, error factors (change of straight pipe length, installation of obstacle or effect of foreign substances on water level sensor) that can often occur in the field should be derived and the research for optimized installation method should be carried out continuously.

• 지질공학
• /
• 제16권3호
• /
• pp.275-282
• /
• 2006

본 연구는 모형실험장치를 이용하여 인공강우에 의한 산사태 발생특성과 사태물질의 확산거동특성을 파악하기 위하여 수행되었다. 본 연구에서는 강우강도와 사면경사의 변화에 따른 다양한 실험조건하에서 일정 시간 간격으로 간극수압, 사면붕괴양상 및 변위, 그리고 토사의 확산면적 등을 각각 측정하였다. 실험 중 복수의 비디오 카메라와 디지털 스틸카메라로 촬영한 후, 이미지 분석을 실시하여 시간대별 산사태 발생양상 및 사태물질 확산특성 자료를 취득하였다. 실험결과에 따르면, 간극수압은 강우강도 및 사면경사에 비례하여 변화하며 이에 따라 강우강도 및 사면경사가 커짐에 따라 산사태가 발생할 가능성도 증가하였다. 사태물질의 확산면적은 강우강도, 강우지속시간, 그리고 사면경사의 증가에 비례하는 양상을 가짐을 확인하였다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 춘계학술대회 논문집
• /
• pp.215-218
• /
• 2009

A design of a subscale solid propellant rocket motor was conducted to do the similitude experiments for the large scale rocket motor. One of the main factor to subscale was the mach number of the solid propellant flume through a nozzle exit The analysis of the flume flow was done to obtain the mach number for the large and subscale rocket motor. The flume shapes on the non dimensional axises by the nozzle exit diameter was matched each other. The propellant grain of a subscale solid rocket motor was designed by the profile of pressure vs time obtained by the mach number of the flume shape. Some analyses of the theoretical solution were compared with the results of the ground static test.

• 한국농공학회지
• /
• 제10권1호
• /
• pp.1377-1387
• /
• 1968

In order to measure runoff and soil losses produced in a small test plot during rainfall, it is usually insufficient to use a tank only, necessitating the combined use of a main tank and a subsidiary tank. Accordingly. exact measurement largely depends on how to connect those two measuring tanks. The main purpose of this thesis is to improve the connecting parts of two measuring tanks so as to assure exact measurement of runoff and soil losses. In this experiment, two types of main tank, i. e. A-type and B-type, were used. A-type is a square tank having a flume at its end. At the flume, ten apertures are provided by using metal columns so as to be able to catch one tenth of total muddy flow discharging at the end of the flume, One tenth of total flow is led to the subsidiary tank through a slot sampler fixed to an aperture. B-type differes in that its flume does not have apertures and slot sampler is fixed directly to the end of the flume, other features being the same as those of A-type. Discharge volumes were measured by using weighing tanks and compared. The effect of baffle screen provided in the flume was also observed in connection with exact measurements. In order to keep main tank and its flume in a horizontal position, bolts and nuts mechanism was used. Vertical and horizontal screens were provided in the main to prevent coarse sands coming into the flume. The conclusion derived through this experiment is as follows: (1) The discharge through slot sampler at each aperture is almost the same for A-type. However, it is slightly more than one tenth of total discharge volume. (2) In case that baffle screen is provided in the flume of A-type tank, the discharge volume of slot sampler is less than that of the same type without screen. (3) For B-type tank, slot sampler discharge increases as slot sampler nears toward the center of flume. (4) When baffle screen is provided in the flume of B-type, slot sampler discharge is less than that of the same type without screen, and this phenomenon is more apparent as compared with A-type. (5) In case that the slot width of slot sampler for B-type is one inch, slot sampler discharge exceeds one tenth of total discharge volume. (6) When the slot width for B-type is 15/16 inch and slot sampler is fixed 3/8 inch apart from either flume wall, slot sampler discharge is approximately equal to one tenth of total discharge volume.

• 한국농공학회지
• /
• 제19권4호
• /
• pp.4533-4543
• /
• 1977

The purpose of this study was to investigate and compare flow discharges of rectangular, V-notch and trapezoidal type of cutthrooat flumes, and the published data for trapezoidal parshall flumes. And the trapezoidal cutthroat flumes were also compared in their accuracy of discharge measurements for various convergence ratios in the inlet section and divergence ratios in the outlet section. Five flumes were studied, and all the flumes were 45cm long with flat-bottom and were made of well-finished transparent acryl plate of 3mm thickness. One rectangular, one V-notch and three trapezoidal types were numbered 1 to 5 as shown in Fig. III-1. The measured depth of water was ranged from 5 to 20cm. The results obtained in this study are summarized as follows: 1. The general discharge equations for tested prototypes are listed for free flow in Table IV-1 and for submergence flow in Table IV-4. 2. In both free and submerged flow, the accuracy of the discharge formula obtained by this test is highly significant at 1% level as shown in Table IV-2 and Table IV-6. The accuracy of disharges measured depends upon the convergence and divergence ratios in the trapezoidal types: the less the ratios of convergence as well as divergence, the lower the accuracy. 3. Submergence ratios tend to increase in the order of flume number except flume No. 4. This implies that trapezoidal cutthroat flumes are more acceptable than rectangular or V-notch ones for free flow. 4. The transition submergence for the trapezoidal Parshall flumes ranges from 80-85 percent, which is slightly higher than the tested flume. However, the trapezoidal cutthroat flume No. 5 has higher transition submergence ratio, ranging from 73-78 percent, than other trapezoidal ones. The difference between the trapezoidal Parshall flumes and the trapezoidal cutthroat flumes in transition submergence seems small enough to be ignored in their field use. 5. Trapezoidal cutthroat flume is simple and economical to construct in existing openchannels whose shapes are generally trapezoidal. In order to obtain the best rating accuracy, flume No. 3 among the tested trapezoidal types is recommended, because it shows the highest accuracy for both free and submerged flow.

• 지질공학
• /
• 제29권4호
• /
• pp.541-552
• /
• 2019

본 연구에서는 강우침투에 따른 사면 내 지반특성변화 및 붕괴특성을 파악하기 위해 산사태 모형실험을 수행하였다. 실험재료로는 국내에서 산사태가 가장 빈번하게 발생하는 화강암 풍화토와 편마암 풍화토를 사용하였고, 시간당 200 mm의 극한강우를 살수함으로써 사면붕괴를 유발하였다. 계측기는 모형사면의 선단부, 사면부, 정상부에 심도별로 천부(GL-0.2 m), 중부(GL-0.4 m), 심부(GL-0.6 m)의 위치에 3 set씩 설치하였고, 데이터는 10초 간격으로 측정하였다. 실험이 종료된 후 실험조건별 지반특성변화를 토대로 불포화이론을 적용하여 사면안정해석을 하였으며, 이를 실제 붕괴형태와 비교·분석을 하였다. 분석결과 사면안전율은 붕괴형태에 대한 현상을 반영하였고, 강우가 침투함에 따라 급격하게 감소하면서 사면붕괴에 이르는 것으로 나타났다. 또한 사면안전율이 1 이하로 떨어지는 시점과 실제 붕괴시점을 비교해보았을 때 화강암 풍화토의 경우 평균 1,600초, 편마암 풍화토의 경우 평균 5,400초 차이가 나타났다.

• 물과 미래
• /
• 제12권1호
• /
• pp.49-55
• /
• 1979

도시화가 유역의 수문학적 특성에 미치는 영향을 연구하기 위해 선정된 반월신공업도시내 2개 시험유역의 유량계측시설인 파샬수로에 대한 모형실험을 실시하였다. 시험유역의 100년 홍수량을 기준으로 하고 수리실험실의 유량공급능력을 감안하여 모형수로의 축척을 결정하였으며 모형실험자료의 분석에 의해 수색과 유량간의 검정공식을 유도하였고 이를 Parshall의 실험식과 비교하였으며, 현지에서의 유량측정을 위한 원형수로의 유량검정공식은 상사율에 의해 모형실험자료를 분석 처리함으로서 획득할 수 있었다.

• 지질공학
• /
• 제24권2호
• /
• pp.191-199
• /
• 2014

We describe a method for detecting slope instability in flume tests using pore pressure and water content data in conjunction with a statistical control chart analysis. Specifically, we conducted univariate statistical analysis on x-MR control chart data (pore pressure and water content) collected at several points along the flume slope, which we separated into three parts: upper, middle, and lower. To assess our results in the context of landslide forecasting and warning systems, we applied control limit lines at $1{\sigma}$, $2{\sigma}$, and $3{\sigma}$ levels of uncertainty. In doing so, we observed that dispersion time varies depending on the control limit line used. Moreover, the detection of instabilities is highly dependent on the position and type of sensor. Our findings indicate that different characteristics of the data on various factors predict slope failure differently and these characteristics can be identified by univariate statistical analysis. Therefore, we suggest that a univariate statistical approach is an effective method for the early detection of slope instability.

• 대한조선학회논문집
• /
• 제38권1호
• /
• pp.37-42
• /
• 2001

본 논문에서는 유연한 그물 구조로 된 새로운 개념의 소파 장치를 제안한다. 본 연구를 하게된 동기는 이미 알려져 있는 기존의 소파장치들이 작은 파수조에서는 제대로 그 역할을 하지 못한다는 점에서 시작되었다. 소파기의 성능을 파악하기 위하여 소파기의 길이와 소파기의 면적을 변화시켜 여러 가지 파장의 파에 대해서 실험을 수행하였다. 실험 결과 제안된 소파 장치는 그 길이가 짧은 파수조에서도 뛰어난 성능을 발휘함을 알 수 있었다.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2023년도 학술발표회
• /
• pp.35-35
• /
• 2023

The main reason for its instability is sediment scouring downstream of hydraulic structures. Both physical and numerical models have been used to investigate the influence of soil properties on scour hole geometry. Nevertheless, no research has been conducted on resistance parameters that affect sedimentation and erosion. In addition, auxiliary structures like wing walls, which are prevalent in many real-world applications, have rarely been studied for their impact on morphology. The hydraulic characteristics of steady flow through a boxed culvert are calibrated using a 3D Computational Fluid Dynamics model compared with experimental data in this study, which shows a good agreement between water depth, velocity, and pressure profiles. Test cases showed that 0.015 m grid cells had the lowest NRMSE and MAE values. It is also possible to quantify sediment scour numerically by testing roughness/d₅₀ ratios (c_s) and diversion walls at a meander flume outlet. According to the findings, c_s = 2.5 indicates a close agreement between numerical and analytical results of maximum scour depth after the culvert; four types of wing walls influence geometrical deformation of the meander flume outlet, resulting in erosion at the concave bank and deposition at the convex bank; two short headwalls are the most appropriate solution for accounting for small changes in morphology. A numerical model can be used to estimate sediment scour at the meander exit channel of hydraulic structures based on the roughness parameter of soil material and headwall type.