• Journal of computational fluids engineering
• /
• v.21 no.3
• /
• pp.77-88
• /
• 2016

A parametric study on a fluidic oscillator was performed numerically in this work. Three-dimensional unsteady Reynolds-averaged Navier-Stokes equations were solved to analyze the flow in the fluidic oscillator. As turbulence closure, $k-{\varepsilon}$ model was employed. Validation of the numerical results was performed by comparing numerical results with experimental data for frequency of the oscillation. The parametric study was performed using five geometric parameters. Performance of the fluidic oscillator was evaluated in terms of velocity ratio and pressure drop. The results show that the inlet channel width and the distance between splitters are important factors in determining the performance of the fludic oscillator.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.1
• /
• pp.22-30
• /
• 2004

A micro-fluidic oscillator is used to control a linear actuator in a dynamic microsystem. The pressure difference at its two output ports causes the linear actuator to move, and it is a standard of judging the performance of the oscillator. The performance can be improved by optimizing the geometry of the oscillator, which has to enable fluid jet to switch at low inlet velocity. For this, in this study the relationship between the pressure coefficient (difference) and geometric parameters is obtained through the analysis using the software FLUENT. From the results the optimized model that maximize the output pressure difference is obtained by using a cyclic coordinate method that is one of optimization methods. As a result not only the performance is improved, but also the working range is more widen.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.11
• /
• pp.747-754
• /
• 2022

An experimental study was carried out to control a shock-induced boundary layer separation by utilizing the supersonic sweeping jet from the fluidic oscillator. High-speed schlieren, surface flow visualization, wall pressure measurement and precise Pitot tube measurement were applied to observe the influences of the location and the supply pressure of the fluidic oscillator on the characteristics of the oblique-shock-induced boundary layer separation. The characteristics of the separation control by the present supersonic fluidic oscillator was quantitatively analyzed by comparing with a conventional control method utilizing an air-jet vortex generator.

• Journal of the Korean Society of Visualization
• /
• v.18 no.1
• /
• pp.50-58
• /
• 2020

This paper presents flow characteristics of a sweeping jet issued by a feedback-free fluidic oscillator. Overall flow characteristics of feedback-free sweeping jet (FFSJ) were analyzed using flow visualization. The feedback-free sweeping jet has a sinusoidal external flow pattern. The oscillating frequency of the FFSJ is three times higher than that of a conventional sweeping jet at the same Reynolds number. Flow structure and turbulence characteristics were investigated using time-resolved particle image velocimetry (TR-PIV). In instantaneous velocity fields, the flow did not stay at ends but changed the direction continuously in contrast to the conventional sweeping jet. Velocity distributions at each plane which were extracted from mean velocity field has Gaussian distribution, which is similar with a circular jet. The sweep angles were constant as 45° at all Reynolds numbers in the high flow rate regime.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.3
• /
• pp.167-174
• /
• 2020

A study of flow characteristics of supersonic fluidic oscillators with shared feedback channel inside was carried out. Unsteady CFD analysis were performed and the numerical results were validated by comparison with the experimental ones observed for the same operation conditions. It was found that the mass flow between individual oscillators through the shared feedback channel directly influenced on the oscillating flow mechanism inside the oscillator, and finally on the synchronization of the jet oscillations. It was also observed that the oscillator with shared feedback channel provided higher pressure loss as well as higher oscillation frequency as compared to the single oscillator of the same geometric shape.

• Journal of the Korean Society of Visualization
• /
• v.16 no.3
• /
• pp.16-25
• /
• 2018

PIV experiments were carried out to visualize the velocity distribution of the sweeping jet impinging onto a flat plate and kinematic behavior of the jet from the fluidic oscillator. Two parameters such as four different Re cases and four different jet-to-wall distances were examined. Time-resolved two dimensional PIV measurements were performed for both streamwise and normal planes respect to the jet axis. Ensemble averaged and phase averaged velocity fields were obtained for the tested range of parameters. The sweeping frequency of the jet increases linearly with increase of Re. The kinetic energy of the sweeping jet decreases as the distance from the jet to the impinging plate increases. In addition, turbulence flow is generated due to the swinging motion of sweeping jet, and various vortices such as primary and secondary vortex are observed near the impinging wall.

• Journal of the Korean Society of Visualization
• /
• v.17 no.2
• /
• pp.58-66
• /
• 2019

This study investigated heat transfer and flow characteristics of a sweeping jet issued from a rectangular nozzle with a thin plate. A thin vertical aluminum plate was attached on outlet of fluidic oscillator to increase velocity of central area with Coanda effect and enhance heat transfer performance. From visualization and PIV experiments, sweeping jet with a thin plate has larger velocity distribution in center region than that of the normal sweeping jet while oscillating frequency is similar as the normal one. Thermographic phosphor thermometry method was used to visualize the temperature field and Nu distribution of plate with impinging sweeping jet with thin plate. Four Reynolds numbers and three jet-to-wall distances were selected as parameters. It is found that heat transfer performance in the low jet-to-wall spacing was enhanced as the cooled area was expanded. However, when the jet-to-wall spacing became greater than 8dh, heat transfer performance became similar due to reduced impinging velocity.