• Proceedings of the Korea Society of Environmental Toocicology Conference
• /
• 2002.10a
• /
• pp.168-168
• /
• 2002

To establish a test protocol for the rodent 20-day thyroid/pubertal assay, flutamide and diethylstilbestrol (DES) were administered to intact male Sprague-Dawley rats from postnatal day 33 for 20 days. Flutamide (1, 5, and 25 mg/kg/day) or DES (10, 20, and 40 ug/kg/day) was given once daily by oral gavage to immature male rats. Prepuce separation was significantly delayed in flutamide group and in DES group. One day after the last dose, the rats were killed and pituitary, thyroid, and reproductive organs were removed and weighed. Flutamide treatment resulted in a significant reduction in the weights of epididymides, ventral prostate, seminal vesicles plus coagulating glands and fluid (SVCGF), levator ani. bulbocarvenus muscles (LABC), Cowper's glands, and glans penis. The weight of adrenal glands decreased at % mg/kg/day, while testes and any other organ weights were unaffected. No microscopic changes were observed in the thyroid glands. Serum levels of testosterone wert significantly increased in the flutamide-treated groups and serum levels of estradiol were also increased. A significant reduction in the weights of testes, epididymides, ventral prostate, SVCGF, LABC, Cowpers glands, and glans penis of DES treated group. Serum testosterone and LH decreased significantly in DES group. Decrease of estradiol was observed, but not significant. These results indicate that flutamide and DES delay puberty in the male rat and its mode of action appears to be via altered secretion of steroids, which subsequently affect the development of the reproductive tract. (Supported by the grant from NITR/Korea FDA for Endocrine Disrupter Research.)

• Korean Journal of Pharmacognosy
• /
• v.43 no.4
• /
• pp.279-285
• /
• 2012

The Mume Fructus (MF) has been used for relieves cough, arrests arrest chronic diarrhea, treat fluid depletion, and treat ascariasis in Korea. In this study, a high-performance liquid chromatography (HPLC) method was established for simultaneous determination of six main components of MF. Additionally, we were investigated the anti-inflammatory and anti-allergic effects of MF extract on lipopolysaccharide (LPS)-treated RAW264.7 cells and tumor necrosis factor (TNF)-${\alpha}$/interferon (IFN)-${\gamma}$-treated HaCaT cells. The analytical column for separation was used a Gemini $C_{18}$ column maintained at $40^{\circ}C$. The mobile phase consisted of 1.0% (v/v) acetic acid in water (A) and 1.0% (v/v) acetic acid in acetonitrile (B). The flow rate was 1.0 mL/min and the detector was a photodiode array (PDA) set at 280 nm and 320 nm. We evaluated the inhibitory effect of MF extract on the production of inflammatory markers, nitric oxide (NO) and prostaglandin $E_2$ ($PGE_2$) in LPS-stimulated RAW264.7 cells and thymus- and activation-regulated chemokine (TARC/CCL17) in TNF-${\alpha}$/IFN-${\gamma}$-treated HaCaT cells, respectively. We confirmed the genes expression related with TARC, macrophage-derived chemokine (MDC/CCL22) and regulated on activation, normal T cell expressed and secreted (RANTES/CCL5) in HaCaT keratinocyte cells by MF extract. The contents of the five compounds in MF were 0.22-1.01 mg/g. Also, the MF extract show inhibition of about 78% and 75% on NO and $PGE_2$ production at the concentration 1000 mg/mL in RAW264.7 cells. MF extract suppressed the hTARC level and genes expression such as TARC, MDC, and RANTES on TNF-${\alpha}$/IFN-${\gamma}$-treated HaCaT cells.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.12
• /
• pp.831-840
• /
• 2019

Flush Air Data Sensing system (FADS) estimates air data states using pressure data measured at the surface of flight vehicles. The FADS system does not require intrusive probes, so it is suitable for high performance aircrafts, stealth vehicles, and hypersonic flight vehicles. In this study, calibration procedures and solution algorithms of the FADS for a sphere-cone shape vehicle are presented for the prediction of air data from subsonic to supersonic flights. Five flush pressure ports are arranged on the surface of nose section in order to measure surface pressure data. The algorithm selects the concept of separation for the prediction of flow angles and the prediction of pressure related variables, and it uses the pressure model which combines the potential flow solution for a subsonic flow with the modified Newtonian flow theory for a hypersonic flow. The CFD code which solves Euler equations is developed and used for the construction of calibration pressure data in the Mach number range of 0.5~3.0. Tests are conducted with various flight conditions for flight Mach numbers in the range of 0.6~3.0 and flow angles in the range of -10°~+10°. Air data such as angle of attack, angle of sideslip, Mach number, and freestream static pressure are predicted and their accuracies are analyzed by comparing predicted data with reference data.

• Microbiology and Biotechnology Letters
• /
• v.16 no.5
• /
• pp.335-342
• /
• 1988

An anion exchange chromatography was employed for the purification of mouse monoclonal antibodies from ascitic fluid and in vitro cultivation media. After cultivation of hybridomas, Alps 25-3, HCGK, A4W, and KW, producing IgG1, the culture supernatants were harvested by centrifugation, precipitated with 50-60％ ammonium sulfate, and dialyzed against 0.025 M Tris-HCI buffer (pH 8.2). Then the dialyzed samples were loaded into a DEAE-Trisacryl M anion exchange column. Monoclonal antibodies bound to the DEAE-Trisacryl M were eluted with 0.025 M Tris-HCI buffer (pH 8.2) containing 30-40 mM NaCl. In ammonium sulfate precipitation, the recovery of the monoclonal antibody was shown to be 90％ and 84％ from in vitro culture media containing 10％ and 2％ fetal bovine serum, respectively. On the other hand, the pretreatment by ultrafiltration enhanced the yield up to 91％ whereas the purity was lower than that by ammonium sulfate treatment. Subsequently, in the DEAE-Trisacryl M chromatographic separation, the purities and recoveries of all the monoclonal antibodies from both the in vitro culture supernatants and ascitic fluids were 70-80％ and 65％ respectively. The monoclonal antibody, Alps 25-3 could be further purified with a purity of 95％ through an immunoadsorbent chromatography.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.34 no.3
• /
• pp.213-217
• /
• 2001

In order to develop a new separation technology, supercritical fluid extraction process was used to produce high purity pigments and fatty acids from seaweed (Undaria pinnatifida). Supercritical carbon dioxide was used as a solvent and ethanol as an entrainer. The sample was treated by a frozen drier and experiments were conducted with a semi-batch flow system at various operating conditions (pressure range, $10.3\~17.2$ MPa; temperature range, $30\~45^{\circ}C$: particle size, $500\~1,000{\mu}m$ extraction time, 60 min). Characteristics of the recovered pigment (chlorophyll a) and fatty acids were determined by UV-spectrophotometry and gas chromatography, respectively. The highest extraction efficiency for fatty acids and pigments was achieved at 12.4 MPa, $35^{\circ}C$, $500{\mu}m$of seaweed size.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.27 no.4
• /
• pp.278-285
• /
• 1991

The authors propose to use the slot system in order to improve of the efficiency for the cambered otter boards. The experiment is divided into 2 parts, one is the efficiency model test, and the other is the visualization model test. The hydrodynamic characteristics of the model otter boards were tested by efficiency model test to measure the shearing, drag force of the models and visualization test using hydrogen bubble method to observe the streak-line and time-line of flow around the models, and milk spout method to observe the separation zone in the wake behind the models. This study tested for 5 models such ad without slot, slot position 0.2C, 0.4C, 0.6C and 0.8C. The results obtained are as follows: \circled1 The maximum C sub(L) of model otter board with slot position 0.6C in attack angle 27$^{\circ}$ was the highest of all models, it's value was 1.59. \circled2 In general, the L/D ratio of the one slot otter boards were 16~28% higher than otter board without slot. \circled3 The slot position 0.6C was better than any other slot position, and it's conformed by visiualization. \circled4 As to the model otter board with slot position 0.6C, flow speed of the back side was faster 1.3 to 1.7 times than in the front side. \circled5 The size of the separated zone in case of the model otter board with 0.6C was smaller than that of any other models.

• Membrane Journal
• /
• v.32 no.2
• /
• pp.150-162
• /
• 2022

In the field of water treatment and pharmaceutical bio an alumina hollow fiber membrane used for mixture separation. However, due to the lack of strengths it is very brittle to handle and apply. Therefore, it is necessary to study and improve the bending strength of the membrane to 100 MPa or more. In this study, as the mixing ratio of the nano-particles increased to 0, 1, 3, and 5 wt%, the viscosity of the fluid mixture increased. The pore structure of the hollow membrane produced by interrupting the diffusion exchange rate of the solvent and non-solvent during the spinning process suppresses the formation of the finger-like structure and gradually increases the ratio of the sponge-like structure to improve the membrane mechanical strength to more than 100 MPa. As a result, an interparticle space was ensured to improve the porosity of the sponge-like structure with high permeability, and it showed excellent N2 permeability of about 100000 GPU and high water permeability of 3000 L/m² h. Therefore, it can be concluded, that the addition of γ-Al₂O₃ nanoparticles as sintering aid is an important method to enhance the mechanical strength of the α-alumina hollow fiber membrane to maintain high permeability.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.11
• /
• pp.1007-1018
• /
• 2009

Hydrocyclone is widely used in industry, because of its simplicity in design, high capacity, low maintenance and operational cost. The separation action of a hydrocyclone treating particulate slurry is a consequence of the swirling flow that produces a centrifugal force on the fluid and suspended particles. In spite of hydrocyclone have many advantage, the application for treatment of urban stormwater case study were rare. We conducted a laboratory scale study on treatable potential of micro particles using hydrocyclone filter (HCF) that was a combined modified hydrocyclone with perlite filter cartridge. Since it was not easy to use actual storm water in the scaled-down hydraulic model investigations, it was necessary to reproduce ranges of particles sizes with synthetic materials. The synthesized storm runoff was made with water and addition of particles; ion exchange resin, road sediment, commercial area manhole sediment, and silica gel particles. Experimental studies have been carried out about the particle separation performance of HCF-open system and HCF-closed system. The principal structural differences of these HCFs are underflow zone structure and vortex finder. HCF was made of acryl resin with 120 mm of diameter hydrocyclone and 250 mm of diameter filter chamber and overall height of 800 mm. To determine the removal efficiency for various influent concentrations of suspended solids (SS) and chemical oxygen demand (COD), tests were performed with different operational conditions. The operated maximum of surface loading rate was about 700 $m^3/m^2$/day for HCF-open system, and 1,200 $m^3/m^2$/day for HCF-closed system. It was found that particle removal efficiency for the HCF-closed system is better than the HCF-open system under same surface loading rate. Results showed that SS removal efficiency with the HCF-closed system improved by about 8~20% compared with HCF-open system. The average removal efficiency difference for HCF-closed system between measurement and CFD particle tracking simulation was about 4%.

• Korean Chemical Engineering Research
• /
• v.53 no.5
• /
• pp.557-564
• /
• 2015

The previous etching, rinsing and drying processes of wafers for MEMS (microelectromechanical system) using SC-$CO_2$ (supercritical-$CO_2$) consists of two steps. Firstly, MEMS-wafers are etched by organic solvent in a separate etching equipment from the high pressure dryer and then moved to the high pressure dryer to rinse and dry them using SC-$CO_2$. We found that the previous two step process could be applied to etch and dry wafers for MEMS but could not confirm the reproducibility through several experiments. We thought the cause of that was the stiction of structures occurring due to vaporization of the etching solvent during moving MEMS wafer to high pressure dryer after etching it outside. In order to improve the structure stiction problem, we designed a continuous process for etching, rinsing and drying MEMS-wafers using SC-$CO_2$ without moving them. And we also wanted to know relations of states of carbon dioxide (gas, liquid, supercritical fluid) to the structure stiction problem. In the case of using gas carbon dioxide (3 MPa, $25^{\circ}C$) as an etching solvent, we could obtain well-treated MEMS-wafers without stiction and confirm the reproducibility of experimental results. The quantity of rinsing solvent used could be also reduced compared with the previous technology. In the case of using liquid carbon dioxide (3 MPa, $5^{\circ}C$, we could not obtain well-treated MEMS-wafers without stiction due to the phase separation of between liquid carbon dioxide and etching co-solvent(acetone). In the case of using SC-$CO_2$ (7.5 Mpa, $40^{\circ}C$), we had as good results as those of the case using gas-$CO_2$. Besides the processing time was shortened compared with that of the case of using gas-$CO_2$.

• Economic and Environmental Geology
• /
• v.48 no.1
• /
• pp.51-63
• /
• 2015

I produced a secular variation model of geomagnetic field by using the magnetic component data from four geomagnetic observatories located in Northeast Asia during the years between 1997 and 2011. The Earth's magnetic field varies with time and location due to the dynamics of fluid outer core and the magnetic observatories on the surface measure in time series. To adequately represent the magnetic field or secular variations of the Earth, a spatio-temporal model is required. In making a global model, satellite observations as well as limited observatory data are necessary to cover the regions and time intervals. However, you need a considerable work and time to process a huge amount of the dataset with complicated signal separation procedures. When you update the model, the same amount of chores is demanded. Besides, the global model might be affected by the measurement errors of each observatory that are biased and the processing errors in satellite data so that the accuracy of the model would be degraded. In this study, as considered these problems, I introduced a localized method in modeling secular variation of the Earth's magnetic field over Northeast Asia region. Secular variation data from three Japanese observatories and one Chinese observatory that are all in the INTERMAGNET are implemented in the model valid between 1997 to 2011 with the interval of 6 months. With the resulting model, I compared with the global model called CHAOS-4, which includes the main, secular variation and secular acceleration models between 1997 to 2013 by using the three satellites' databases and INTERMAGNET observatory data. Also, the geomagnetic 'jerk' which is known as a sudden change in the time derivatives of the main field of the Earth, was discussed from the localized secular acceleration coefficients derived from spline models.