• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 추계학술대회 논문집
• /
• pp.156-160
• /
• 2007

Ejector system is a device to transport a low-pressure secondary flow by using a high-pressure primary flow. Ejector system is, in general, composed of a primary nozzle, a mixing section, a casing part for suction of secondary flow and a diffuser. It can induce the secondary flow or affect the secondary chamber pressure by both shear stress and pressure drop which are generated in the primary jet boundary. Ejector system is simple in construction and has no moving parts, so it can not only compress and transport a massive capacity of fluid without trouble, but also has little need for maintenance. Ejectors are widely used in a range of applications such as a turbine-based combined-cycle propulsion system and a high altitude test facility for rocket engine, pressure recovery system, desalination plant and ejector ramjet etc. The primary interest of this study is to set up an applicable model and operating conditions for an ejector in the condition of sonic and subsonic, which can be extended to the hydrogen fuel cell vehicle. Experimental and theoretical investigation on the sonic and subsonic ejectors with a converging-diverging diffuser was carried out. Optimization technique and numerical simulation was adopted for an optimal geometry design and satisfying the required performance at design point of ejector for hydrogen recirculation. Also, some sonic and subsonic ejectors with the function of changing nozzle position were manufactured precisely and tested for the comparison with the calculation results.

• 소음진동
• /
• 제6권2호
• /
• pp.163-177
• /
• 1996

An investigation on thermohydraulic stability of flow oscillations in the CANada Deuterium Uranium-600(CANDU-6) heat transport system has been conducted. Flow oscillations in reactor coolant loops, comprising two heat sources and two heat sinks in series, are possibly caused by the response of the pressure to extraction of fluid in two-phase region. This response consists of two contributions, one arising from mass and another from enthalpy change in the two-phase region. The system computer code used in the investigation os SOPHT, which is capable of simulating steady states as well as transients with varying boundary conditions. The model was derived by linearizing and solving one-dimensional, homogeneous single- and two-phase flow conservation equations. The mass, energy and momentum equations with boundary conditions are set up throughout the system in matrix form based on a node-link structure. Loop stability was studied under full power conditions with interconnecting the two compressible two phase regions in the figure-of-eight circuit. The dominant function of the interconnecting pipe is the transfer of mass between the two-phase regions. Parametric survey of loop stability characteristics, i. e., damping ratio and period, has been made as a function of geometrical parameters of the interconnection line such as diameter, length, height and orifice flow coefficient. The stability characteristics with interconnection line has been clarified to provide a simple criterion to be used as a guide in scaling of the pipe.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 춘계학술대회논문집
• /
• pp.256-259
• /
• 2008

Ejector system is a device to transport a low-pressure secondary flow by using a high-pressure primary flow. Ejector system is, in general, composed of a primary nozzle, a mixing section, a casing part for suction of secondary flow and a diffuser. It can induce the secondary flow or affect the secondary chamber pressure by both shear stress and pressure drop which are generated in the primary jet boundary. Ejector system is simple in construction and has no moving parts, so it can not only compress and transport a massive capacity of fluid without trouble, but also has little need for maintenance. Ejectors are widely used in a range of applications such as a turbine-based combined-cycle propulsion system and a high altitude test facility for rocket engine, pressure recovery system, desalination plant and ejector ramjet etc. The primary interest of this study is to set up an applicable model and operating conditions for an ejector in the condition of sonic and subsonic, which can be extended to the hydrogen fuel cell vehicle. Experimental and theoretical investigation on the sonic and subsonic ejectors with a converging-diverging diffuser was carried out. Optimization technique and numerical simulation was adopted for an optimal geometry design and satisfying the required performance at design point of ejector for hydrogen recirculation. Also, some ejectors with a various of nozzle throat and mixing chamber diameter were manufactured precisely and tested for the comparison with the calculation results.

• Journal of Advanced Marine Engineering and Technology
• /
• 제39권10호
• /
• pp.1002-1010
• /
• 2015

Natural gas hydrates are newly emerging as an environment-friendly source of energy to substitute for fossil fuels in the 21stcentury.NGHs are reported to holds much amounts of natural gas (up to 182 standard volumes of gas per volume of hydrate); they are easy to store and safe to carry at about minus 20 degree Celsius under atmospheric pressure because of the self-preservation phenomenon of gas hydrates. The transporting method by gas-ice-hydrate ship carriers has been introduced and developed by a variety of industry and research institutions. Our team has been conducted to develop NGH total systems, including a breakthrough NGH carrier for sea transportation, since 2011. The NGH pellet carrier does not require a separate cooling system for cargo, and the initial temperature is maintained through insulation of the cargo tanks throughout the transport to the final destination. The heat conducted from the exterior and passing through the insulation material of the hull should be cut off as much as possible, but heat inflow inside the cargo tank from an external source is inevitable during transport. In this study, the heat transfer in a cargo tank of a 115K NGH carrier was analyzed through simulation with a commercial CFD code to estimate the boil-off gas/boil-off rate on the developed carrier and understand major hazards that could significantly impact the safety of the vessel.

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권6호
• /
• pp.615-624
• /
• 2014

핀-튜브 열교환기는 산업용 보일러, 라디에이터, 냉동기 등에 많이 사용되고 있어 열교환기의 성능향상을 위한 다양한 연구가 진행되고 있다. 본 연구에서는 Plain형 핀-튜브 열교환기에 대해 가로피치, 와류발생기위치, 튜브표면의 돌기형상 및 돌기개수 등의 변화에 따른 열전달 및 압력강하 특성을 이론적으로 해석하였다. CFD 해석시 경계조건으로는 SST 난류모델을 적용하였으며, 튜브표면의 온도는 333 K이고, 입구측 공기의 온도와 속도는 423~438 K, 1.5~2.1 m/s로 가정하였다. 해석결과로는 열전달계수는 가로피치에 대한 영향은 큰 차이가 없으며, 열전달특성은 와류발생기 설치가 튜브 전방부에 위치할수록 양호한 것으로 나타났다. 또한 튜브표면의 돌기형상은 열전달 및 압력강하 특성에서 원형이 톱니형과 삼각형보다 적절하였으며, 16개 원형 돌기형상이 가장 양호하였다.

• 한국수자원학회논문집
• /
• 제56권2호
• /
• pp.125-137
• /
• 2023

지속적으로 증가하는 플라스틱의 사용으로 인하여 현재 해안·해양 환경에서 플라스틱을 찾기란 어렵지 않은 일이 되었다. 하천을 통해 해양으로 유출된 플라스틱 폐기물은 해안 지역에서 장기간 머물며, 파랑, 바람, 유사, 인간 활동 등과 같은 다양한 요인들과 상호작용하며 물리적·화학적 변화를 겪게 된다. 이에, 실험적 연구를 통하여 해안 유사에서 수체로의 플라스틱 입자 방출 과정을 고찰하고자 하였다. 본 연구는 고 레이놀즈 수를 가지는 왕복 흐름과 유사 이동을 구현하기 위한 왕복흐름발생장치를 제작하여 진행되었고, 세 가지의 크기를 가지는 매끈한 구형의 플라스틱 입자를 사용하였다. 실험 결과, 유사 내 플라스틱 입자의 방출은 유사 이동에 가장 큰 영향을 받았으며, 이는 흐름의 세기에 비례한다. 더불어, 입자가 작을수록 더 많은 입자가 방출되었다. 결과를 종합하여 입자의 방출을 결정하는 무차원 매개변수들의 임계값을 제시하였다.

• 한국지반신소재학회논문집
• /
• 제12권4호
• /
• pp.143-147
• /
• 2013

지열 에너지는 지구에 저장된 활용하기 쉬운 재생에너지 이며, 열교환 배관 시스템을 통해 수집될 수 있다. 본 연구에서는 터널 주변 라이닝에 지열 에너지를 포집할 수 있는 열교환 파이프 루프를 간편하게 설치할 수 있는 시스템을 개발하였다. 터널 세그먼트에 결합된 열 교환 파이프 루프 시스템은 수송 유체 순환을 통해, 지중 주변의 열을 인근 구조물 또는 지역의 냉난방 열원으로 사용할 수 있다. 터널 세그먼트에 통합 연결된 열 교환 파이프 루프 시스템을 에너지 라이닝 세그먼트(Energy Lining Segment)이라고 명하도록 하겠다. 유럽에서는 터널 라이닝에 열 교환 파이프 루프 시스템을 통합한 수차례의 사례가 있다. 본 연구에서는 에너지 라이닝 세그먼트에 대한 적용성 평가를 위해, 독일 사례와 유럽 도시에 적용된 사례를 조사해 보았다. 또한, 에너지 라이닝 세그먼트의 열 전도특성을 파악하기 위해, 전산유체해석(CFD)을 수행해 보았다.

• 한국결정성장학회지
• /
• 제9권2호
• /
• pp.251-259
• /
• 1999

로울러 킬른 내의 이동현상에 대하여 전산모사를 수행하였다. 소결 공정에서 중요한 요소인 로울러 킬른 내의 온도분포와 속도장을 구하기 위하여 유한요소법을 이용하여 에너지 보존식과 운동량 보존식을 풀었다. 로울러 킬른 내에 세라믹 원료가 없을 경우에, 벽면의 열원으로부터 유입되는 공기로 빠르게 열전달이 이루어지게 되며 공기는 이 열의 대부분을 로울러 킬른 밖으로 전달하는 것을 알 수 있었다. 세라믹 원료가 있을 경우에, 세라믹 원료는 벽면으로부터 열을 받아 온도가 상승하게 되나 상대적으로 차가운 공기의 유동 때문에 인하여 공기로 많은 열을 빼앗기게 되는 것을 알 수 있었다. 자연대류에 의한 열전달로 인하여 소성대인 영역 5에서 세라믹 원료의 바닥과 윗면에서 온도 차이가 255K 정도 생겼다. 마지막으로 복사 열전달을 고려하였을 경우에 세라믹 원료 표면에서의 복사 열전달로 인하여 전도와 자연대류만 고려하였을 때보다 온도 차이가 45 K 정도 더 생겼다.

• Parasites, Hosts and Diseases
• /
• 제58권3호
• /
• pp.287-299
• /
• 2020

Cystic echinococcosis (CE) is a zoonotic infection caused by Echinococcus granulosus larvae. It seriously affects the development of animal husbandry and endangers human health. Due to a poor understanding of the cystic fluid formation pathway, there is currently a lack of innovative methods for the prevention and treatment of CE. In this study, the protoscoleces (PSCs) in the encystation process were analyzed by high-throughput RNA sequencing. A total of 32,401 transcripts and 14,903 cDNAs revealed numbers of new genes and transcripts, stage-specific genes, and differently expressed genes. Genes encoding proteins involved in signaling pathways, such as putative G-protein coupled receptor, tyrosine kinases, and serine/threonine protein kinase, were predominantly up-regulated during the encystation process. Antioxidant enzymes included cytochrome c oxidase, thioredoxin glutathione, and glutathione peroxidase were a high expression level. Intriguingly, KEGG enrichment suggested that differentially up-regulated genes involved in the vasopressin-regulated water reabsorption metabolic pathway may play important roles in the transport of proteins, carbohydrates, and other substances. These results provide valuable information on the mechanism of cystic fluid production during the encystation process, and provide a basis for further studies on the molecular mechanisms of growth and development of PSCs.

• Journal of Advanced Marine Engineering and Technology
• /
• 제32권7호
• /
• pp.1051-1060
• /
• 2008

Now days, various types of ships are operated to transport both cargo and passengers all around the world. Most of the important auxiliary machinery installed in those ships is fluid machinery such as pumps, compressors, and fans. A large percentage of fluid machinery is pumps which are classified as turbo and positive displacement pumps. This paper analyzes only turbo pumps out of the two types. This thesis has two aims: (a) to analyze the present status of pumps installed in merchant and training ships and (b) to find the correlation among sea going pump kW, port pump kW, GE kW, ME MCR, number of pumps, ME kgf, pump kgf. Based on the ship's type, my paper seeks to find special characteristics as a result of analyzing head, flow rate, and kW. Moreover this paper analyzes and compares number of pumps, rpm of pumps, pump kW/ME MCR and pump kW/GE kW under the conditions of seagoing and berthing according to the ship's type. In conclusion, (1) For the exact comparison, information on the head, kW, flow rate, number of pumps by ship's type, the pump installation status of the Merchant Ships and Training Ships were tabulated and compared in this paper. (2) In order to qualify one ship as the delegate ship, several methods were used. The result of the examination indicates that the chosen ships could be justified as a suitable representation of ships of their own type. (3) The correlation of several values(total pump kW, port pump kW, GE kW, seagoing pump kW, pump weight, ME weight, ME MCR, number of pumps and ME kW) could be obtained.