• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 춘계학술대회논문집
• /
• pp.180-183
• /
• 2005

The engine mount of vehicle systems is role of support engine mass and isolate noise and vibration from engine disturbance forces. One of attractive candidates to achieve this goai is to utilize a semi-active ER engine mount. By applying this, we can effectively control damping force and hence the noise and vibration by just controlling the intensity of electric field. However, control performance of the engine mount may be very sensitive to temperature variation during engine operation. In this work, we Investigate dynamic performances of ER engine mount with respect to the temperature variation. In order to undertake this, a flow-mode type of ER engine mount is designed and manufactured. Displacement transmissibility is experimentally and numerically evaluated as a function of the electric field. The ER engine mount is then incorporated with full-vehicle model in order to investigate vibration control performance. After formulating the governing equation of motion, a semi-active controller is designed. The controller is implemented through a hardware-in-the-loop simulation (HILS), and control responses such as acceleration level at various engine speeds are evaluated in the frequency and time domains.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.980-985
• /
• 2008

This paper presents vehicle road test of a semi-active suspension system equipped with continuously controllable magnetorheological (MR) dampers. As a first step, front and rear MR dampers are designed and manufactured based on the optimized damping force levels and mechanical dimensions required for a commercial middle-sized passenger vehicle. After experimentally evaluating dynamic characteristics of the MR dampers, the test vehicle is prepared for road test by integrating current suppliers, real-time data acquisition system and numerous sensors such as accelerometer and gyroscope. Subsequently, the manufactured four MR dampers (two for front parts and two for rear parts) are incorporated with the test vehicle and a skyhook control algorithm is formulated and realized in the data acquisition system. In order to emphasize practical aspect of the proposed MR suspension system, road tests are undertaken on proving grounds: bump and paved roads. The control responses are evaluated in both time and frequency domains by activating the MR dampers.

• 한국소음진동공학회논문집
• /
• 제19권3호
• /
• pp.235-242
• /
• 2009

This paper presents vehicle road test of a semi-active suspension system equipped with continuously controllable magnetorheological(MR) dampers. As a first step, front and rear MR dampers are designed and manufactured based on the optimized damping force levels and mechanical dimensions required for a commercial middle-sized passenger vehicle. After experimentally evaluating dynamic characteristics of the MR dampers, the test vehicle is prepared for road test by integrating current suppliers, real-time data acquisition system and numerous sensors such as accelerometer and gyroscope. Subsequently, the manufactured four MR dampers(two for front parts and two for rear parts) are incorporated with the test vehicle and a skyhook control algorithm is formulated and realized in the data acquisition system. In order to emphasize practical aspect of the proposed MR suspension system, road tests are undertaken on proving grounds: bump and paved roads. The control responses are evaluated in both time and frequency domains by activating the MR dampers.

• 한국소음진동공학회논문집
• /
• 제20권3호
• /
• pp.249-256
• /
• 2010

This paper presents performance analysis of a quarter-vehicle magneto-rheological(MR) suspension system with respect to different tire pressure. As a first step, MR damper is designed and manufactured based on the optimized damping force levels and mechanical dimensions required for a commercial mid-sized passenger vehicle. After experimentally evaluating dynamic characteristics of the manufactured MR damper, the quarter-vehicle MR suspension system consisting of sprung mass, spring, tire and the MR damper is constructed in order to investigate the ride comfort. After deriving the equations of the motion for the proposed quarter-vehicle MR suspension system, vertical tire stiffness with respect to different tire pressure is experimentally identified. The skyhook controller is then implemented for the realization of quarter-vehicle MR suspension system. Ride comfort characteristics such as vertical acceleration RMS and weighted RMS of sprung mass are evaluated under various road conditions.

• Smart Structures and Systems
• /
• 제25권3호
• /
• pp.279-284
• /
• 2020

Electrical current is usually used to change the damping force of Magnetorheological Dampers (MRDs). However, changing the electrical current could shift the stiffness of the system, the phenomenon that was not considered carefully. This study aims to evaluate this shift. A typical MRD was designed, optimized, and fabricated to do some accurate and detailed experimental tests to examine the stiffness variation. The damper is equipped with a circulating system to prevent the deposition of particles when it is at rest. Besides that, a vibration setup was developed for the experimental study. It is capable of generating vibration with either constant frequency or frequency sweep and measure the amplitude of vibration. The damper was tested by the vibrating setup, and it was concluded that with a change in electrical current from 0 to 1.4 A, resonant frequency would change from 13.8 Hz to 16 Hz. Considering the unchanging mass of 85.1 kg, the change in resonant frequency translates as a shift in stiffness, which changes from 640 kN/m to 860 kN/m.

• Journal of Advanced Research in Ocean Engineering
• /
• 제3권4호
• /
• pp.165-173
• /
• 2017

This study aims at validating simulations of the forced and freely vibrating cylinders at Reynolds number of approximately 500 in order to identify the capability of the CFD code, and to establish the analysis process of the vortex-induced vibration (VIV). The direct numerical and large eddy simulations were employed to resolve the various length scales of the vortices, and the morphing technique was used to consider a motion of the circular cylinder. For the forced vibration case, both in- and anti-phase VIV processes were observed regarding the frequency ratio. Namely, when the frequency ratio approaches to unity, the synchronization/lock-in process occurs, leading to substantial increases in drag and lift coefficients. This is strongly linked with the switch in timing of the vortex formation, and this physical tendency is consistent with that of Blackburn and Henderson (J. Fluid Mech., 1999, 385, 255-286) as well as force coefficients. For the free oscillation case, the mass and damping ratio of 50.8 and 0.0024 were considered based on the study of Blackburn et al. (J. Fluid Struct., 2000, 15, 481-488) to allow the direct comparison of simulation results. The simulation results for a peak amplitude of the cylinder and a shedding mode are reasonably comparable to that of Blackburn et al. (2000). Consequently, based on aforementioned results, it can be concluded that numerical methods were successfully validated and the calculation procedure was well established for VIV analysis with reasonable results.

• 한국유체기계학회 논문집
• /
• 제16권3호
• /
• pp.18-25
• /
• 2013

Recently the requirement of long-term mobile energy source for mobile robot or small-sized unmanned vehicle is highly increased, and the micro turbine generator(MTG) which is known to have high energy and power density is under development. MTG is designed to have air foil bearing and high speed rotor of which operating speed is 400,000rpm. In the development stage of high speed rotor and bearing, stability analysis for the full operational speed range is essential and the dynamic coefficients such as stiffness and damping coefficients of bearing depending on the rotational speed are required for that. Although perturbation method is usually used to identify the dynamic coefficients, it's not easy to give the perturbation to the high speed rotating rotor. In this study, we present the dynamic coefficients measurement system for air foil bearing which consists of electromagnets, gap sensors, high speed motor and controller. This measurement system can exert the sine sweep force to the rotor-bearing, measure the displacement of rotor and get FRF(Frequency response function) of rotor-bearing. The least square estimation method is applied to identify the dynamic coefficients of bearing from the measured frequency response at the different rpm and the identified dynamic coefficients for the wide rotational speed range are presented.

• Advances in nano research
• /
• 제16권4호
• /
• pp.325-340
• /
• 2024

There are several novel uses for dispersing many nanoparticles into a conventional fluid, including dynamic sealing, damping, heat dissipation, microfluidics, and more. Therefore, melting heat and mass transfer characteristics of a 3-D MHD Hybrid Nanofluid flow over a rotating disc with presenting dufour and soret effects are assessed numerically in this study. In this instance, we investigated both ferric sulfate and molybdenum disulfide as nanoparticles suspended within base fluid water. The governing partial differential equations are transformed into linked higher-order non-linear ordinary differential equations by the local similarity transformation. The collection of these deduced equations is then resolved using a Chebyshev spectral collocation-based algorithm built into the Mathematica software. To demonstrate how different instances of hybrid/ nanofluid are impacted by changes in temperature, velocity, and the distribution of nanoparticle concentration, examples of graphical and numerical data are given. For many values of the material parameters, the computational findings are shown. Simulations conducted for different physical parameters in the model show that adding hybrid nanoparticle to the fluid mixture increases heat transfer in comparison to simple nanofluids. It has been identified that hybrid nanoparticles, as opposed to single-type nanoparticles, need to be taken into consideration to create an effective thermal system. Furthermore, porosity lowers the velocities of simple and hybrid nanofluids in both cases. Additionally, results show that the drag force from skin friction causes the nanoparticle fluid to travel more slowly than the hybrid nanoparticle fluid. The findings also demonstrate that suction factors like magnetic and porosity parameters, as well as nanoparticles, raise the skin friction coefficient. Furthermore, It indicates that the outcomes from different flow scenarios correlate and are in strong agreement with the findings from the published literature. Bar chart depictions are altered by changes in flow rates. Moreover, the results confirm doctors' views to prescribe hybrid nanoparticle and particle nanoparticle contents for achalasia patients and also those who suffer from esophageal stricture and tumors. The results of this study can also be applied to the energy generated by the melting disc surface, which has a variety of industrial uses. These include, but are not limited to, the preparation of semiconductor materials, the solidification of magma, the melting of permafrost, and the refreezing of frozen land.

• 한국강구조학회 논문집
• /
• 제24권1호
• /
• pp.91-99
• /
• 2012

최근 인접 건축물의 진동제어와 관련된 연구가 몇몇 연구자에 의하여 수행되고 있으며 그리고 구조물의 지진동 제어를 위하여 준능동 감쇠기의 일종인 MR 감쇠기가 적용되고 있다. 본 논문에서는 MR 감쇠기의 위치에 따른 인접 건축물의 지진동 제어성능을 분석하여 MR 감쇠기의 설치에 대한 최적의 위치를 선정하고자 한다. 본 연구를 위하여 인접한 20층과 15층 건축물을 예제 구조물로 사용하였으며 이 예제 구조물은 서로 다른 고유진동수를 갖게 하였으며 예제 구조물의 지진동 제어를 위하여 Groundhook 제어기법을 적용하였다. 예제 구조물의 수치해석에 의한 지진응답 분석결과, 변위응답 제어를 위하여 인접 건축물의 최상층에 MR 감쇠기를 설치하는 것이 제어성능에 있어서 우수하며 가속도응답을 제어하기 위해서는 인접 건축물의 중간층에 MR 감쇠기를 설치하는 것이 우수한 제어성능을 보이고 있다. MR 감쇠기를 중간층에 설치할 경우에, 변위응답과 가속도응답을 동시에 제어가 가능하다. 따라서 건축물의 제어 목표에 따라서 MR 감쇠기 설치위치를 적절하게 선정해야 할 것이다.

• 한국지반신소재학회논문집
• /
• 제21권2호
• /
• pp.57-65
• /
• 2022

본 연구에서는 폭약과 발파공 사이의 충전매질을 통한 충격파 전파 효과를 수치적으로 시뮬레이션하고 검증하였다. 고체(Lagrangian)와 유체(Eulerian)를 혼합 모델링하기 위해 Arbitrary Lagrangian-Eulerian(ALE) 방법을 선택하였다. 시간의존적 해석은 발파공정 시간 동안 수행되었다. 폭약과 매질(공기 또는 물)을 유한 요소망으로 모델링하였고, 발파공은 시작점(폭약)에서 발파공벽에 도달하는 전파 속도와 충격력을 결정할 수 있는 강체로 가정하였다. 해석결과에 따르면 물의 전파속도와 충격력은 공기의 경우보다 컸다. 추가로 발파 작업의 실제 현장을 모델링하고 시뮬레이션하였다. 암석은 탄소성체로 가정하였다. 해석결과에 따르면 충전매질이 물인 경우 순간 충격력이 더 크고, 파쇄블록 크기는 더 작은 것으로 나타났다. 반면 발파공배면에서의 충격량은 물인 경우에 더 작았는데, 이는 파쇄에 충격에너지가 상당부분 사용되고, 파쇄로 인한 감쇠 효과에 의해 주변의 고체를 통한 압력 전파는 공기보다 작아지기 때문이다. 이로써 충전매질로서 물이 공기보다 경제성이 더 높다는 것이 입증되었다.