• 대한기계학회논문집B
• /
• 제24권3호
• /
• pp.338-345
• /
• 2000

A model testing has been performed to investigate the flow characteristics of a vortex chamber, which plays a role of a flow switch and passively controls the discharge flow rate. This method of passive flow control is a matter of concern in the design of advanced nuclear reactor systems as an alternative to the active flow control to provide emergency water to the reactor core in case of postulated accidents like LOCA (Loss-Of-Coolant Accident). By changing the inflow direction in the vortex chamber and varying the flow resistance inside the chamber, the vortex chamber can control passively the injection flowrate. Fundamental characteristics such as discharge flow rate and pressure drop of the vortex chamber are measured, and its parametric effects on the performance of the vortex chamber are also systematically investigated.

• 대한기계학회논문집B
• /
• 제28권2호
• /
• pp.154-159
• /
• 2004

A new microflow rate controller for medical injection was developed and evaluated. The flow rate was controlled by changing the friction depth as well as the friction length of the micro-channel. A precise micro-fabrication of the micro-channel was requested for an accurate flow control. The friction depth was inversely proportional to the friction length, which gives a linear flow control to the channel length. The channel groove was fabricated with a plastic material. A rubber containing silicone oil was covered over the groove, which satisfies both lubrication and leakage prevention. The flow controller was validated by performing the numerical simulation and experiment. A good agreement was shown between computation and experiment.

• 한국자동차공학회논문집
• /
• 제4권3호
• /
• pp.92-101
• /
• 1996

In a gasoline engine, the characteristics of air flow is very important not only for the design of the intake system geometry bout also for the accurate measurement of the induction air mass. In this study, an air flow rate measurement of the induction air mass. In this study, an air flow rate measurement was conducted by using the hot wire flow meter at the upstream of the intake port and the throttle. At the upstream of the throttle, the overshoot phenomena of the air flow rate by fast throttle opening were analyzed with choked flow. At the upstream of the intake port, the cylinder variation of the air flow rate and the difference between fast throttle opening and closing were showed during the unsteady state by the throttle step change. The results of this study can be used for the design of the throttle valve geometry and cylinder by cylinder control.

• 한국정밀공학회지
• /
• 제15권4호
• /
• pp.68-75
• /
• 1998

A one-stage direction and flow control valve was studied theoretically and experimentally. A direction and flow control valve maintains a constant flow rate by changing the spool-orifice area under the variation of valve pressure drop, since the spool-orifice area is varied by the action of flowforces on the spool. A direction and flow control valve has the advantage of simple and low-cost structure compared to a conventional flow control valve utilizing a pressure regulating spool which regulates the pressure drop caused by flow through the metering orifice. The static and dynamic characteristics of a one-stage direction and flow control valve was analyzed. Experimental results on the flow control characteristics of the manufactured valve show satisfactory agreement with simulation results.

• 한국생산제조학회지
• /
• 제22권3호
• /
• pp.465-471
• /
• 2013

Flow rate control is the uppermost concern for a trochoid hydraulic pump. Cavitation within the flow field of the pump has the greatest effect on the flow control during high-speed pump rotation of approximately 3500~4000 RPM. In this paper, based on AMESim$^{(R)}$ and Solid Works$^{(R)}$, we will present a method to simulate cavitation by analyzing the control factors of a trochoid pump, including the hydraulic pressure change at the outlet, flow rate based on the rotation speed of the inner rotor, leakage through the gap between the outer and inner rotors, and discharging angle of the outlet. The proposed methodology of the [cavitation simulation will enable field engineers to more easily design trochoid pumps, and will allow more concrete control over the flow rate of the pump by realizing an analysis model similar to the actual product model.

• 설비공학논문집
• /
• 제26권12호
• /
• pp.572-578
• /
• 2014

Heating energy was measured in an apartment housing unit with a district heating system, varying the kind of hot water distributors. Ondol coils passing through a living room raised the temperature of the room where the heating was turned off. Including this characteristic of Ondol heating into the modeling, we performed simulations and showed a verification by comparison with the results of measurements. As a result, a main flow control method, which changes hot water flow rate supplied to a housing unit according to the thermal load, can reduce the supplied flow rate and lower the return temperature, compared with a constant flow method. That can result in decreased heat loss in utility-pipe conduits even though the heating energy supplied is almost the same. An outdoor reset control that raises the temperature of the supplied hot water if the outdoor temperature falls has the effect of a quicker response in heating than the reduced flow rate and return temperature.

• 대한조선학회논문집
• /
• 제40권5호
• /
• pp.10-16
• /
• 2003

To investigate the jet effect on circulation control, a segment of model was prepared and inserted horizontally across the test section of the cavitation tunnel. The hydrodynamic forces acting on the model were measured under the 2 dimensional flow behavior. Circulation flow control requires higher flow rate of water jet than boundary layer control does. Jet injection is effective in increasing lift coefficient and the increments reach to 160% in a certain combination of parameters such as an angle of attack, jet flow rate and flap angle. The blown water jet not only reduces form drag but also thrust effect, which is sometimes greater than the form drag in specific conditions.

• 한국지능시스템학회:학술대회논문집
• /
• 한국퍼지및지능시스템학회 2003년도 ISIS 2003
• /
• pp.525-530
• /
• 2003

This paper focuses on design of nonlinear power plant controller using immune based multiobjective fuzzy approach. The thermal power plant is typically regulated by the fuel flow rate, the spray flow rate, and the gas recirculation flow rate. However, Strictly maintaining the steam temperature can be difficult due to heating value variation to the fuel source, time delay changes in the main steam temperature. the change of the dynamic characteristics in the steam-turbine system. Up to the present time, PID Controller has been used to operate this system. However, it is very difficult to achieve an optimal PID gain with no experience, since the gain of the PID controller has to be manually tuned by trial and error. These parameters tuned by multiobjective based on immune network algorithms could be used for the tuning of nonlinear power plant.

• 대한한방내과학회지
• /
• 제29권1호
• /
• pp.258-264
• /
• 2008

Objectives : The aim of this study was to confirm the characteristics of oral malodor patients by evaluating the differences of salivary flow rate, secretory immunoglobulin A (sIgA) level in saliva between the patient and control groups, and the correlation with the tongue coating, volatile sulfur compound (VSC), salivary flow rate and sIgA level in saliva in the patients group. Methods : Forty-seven patients with oral malodor and twenty healthy volunteers were included in this study. Their tongue coating was assessed with the Winkel tongue coating index, and salivary flow rate, sIgA concentrations in saliva and the level of VSC in oral cavity were measured. Results : There were no significant differences of the salivary flow rate and the sIgA level in saliva between the patient and control groups, but there was a significant relationship between the accumulation of tongue coating and the level of VSC in oral cavity. Conclusions : Our results suggest that tongue coating is closely related to oral malodor, but further studies are needed to confirm the relationship between tongue coating and sIgA level in saliva.

• Journal of Ecology and Environment
• /
• 제30권2호
• /
• pp.109-119
• /
• 2007

The effect of water flow on the growth of Gafrarium tumidum was studied in the field using open cages constructed with stainless steel net and perspex in which holes were drilled. Cages with different flows (25, 50 and 75% of the control) were made by varying the area of perspex being drilled. Reduction in flow rate was directly proportional to the undrilled area, and the mean flow rate of the different treatment groups varied from 3.12 cm/s for the 25% exposure to 12.48 cm/s for the control cages. At the end of the 3-month experiment, no significant differences in sediment characteristics were found among the treatments. Growth in shell length, shell weight and tissue dry weight was, however, positively correlated with flow rate. Percentage increases ranged from $3.0{\sim}8.3%$ for shell length, $9.9{\sim}23.1%$ for shell weight and $17.2{\sim}53.3%$ for tissue dry weight. Condition index of the clam was not significantly different among the treatments. Seston depletion effect could reduce growth in G. tumidum only when water flow was reduced to 25% of the control. G. tumidum also exhibited different responses in shell and tissue growth at low flow rates, in which shell growth continued to decrease as flow rate decreased whereas tissue growth was relatively independent of low flows at 25 and 50% of the control. It was suggested that when seston flux was reduced at slow flows, it would be a better strategy for G. tumidum to channel energy for gonad development instead of shell growth during the reproductive stage.