• 대한기계학회논문집B
• /
• 제22권12호
• /
• pp.1763-1773
• /
• 1998

In the present experimental study, the flow behavior in a semi-closed two-phase natural circulation loop was examined. Water was used as the working fluid. Heat flux, heater-inlet subcooling, and flow restrictions at the heater-inlet and at the expansion-tank-line were taken as the controlling parameters Six circulation modes were identified by changing heat flux and inlet subcooling conditions ; single-phase continuous circulation, periodic circulation (A), two-phase continuous circulation, and periodic circulations (B), (C), and (D). Among these, the single-phase and two-phase continuous-circulation modes exhibit no significant oscillations and are considered to be stable. Periodic circulation (A) is characterized by the large amplitude two-phase f10w oscillations with the temporal single-phase circulation between them, while periodic circulation (B) featured by the flow oscillations with continuous boiling inside the heater section. Periodic circulation (C) appears to be the manometric oscillation with continuous boiling. Periodic circulation (D) has the longer period than periodic circulation (B) and a substantial amount of liquid flow back and forth through the expansion-tank-line periodically ; this mode is considered the pressure drop oscillation. Parametric study shows that the increases of the inlet- and expansion-tank-line- restrictions and the decrease of inlet subcooling broaden the range of the stable two-phase(continuous circulation) mode.

• 조명전기설비학회논문지
• /
• 제15권2호
• /
• pp.21-30
• /
• 2001

본 논문에서는 UPFC(Unified Power Flow Controller)설치 전력계통에서 어떤 선로의 전력조류를 원하는 값으로 직접 제어함과 동시에 계통 전체의 전력조류해석을 행하는 선로조류제약을 고려한 전력조류해석 알고리즘을 제시하고 이 알고리즘을 UPFC에 의한 과부하선로의 과부하해소제어에 적용하여 UPFC 제어 방법을 제시하고 사례연구를 통하여 UPFC의 제어효과의 효용성을 입증하였다. 또한 효과적인 조류해석을 위한 UPFC의 직·병렬 전압원의 초기치를 설정하는 공식을 유도하였다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제37회 추계학술대회논문집
• /
• pp.801-804
• /
• 2011

추진제 탱크와 배관의 연결부에 대한 개념 설계단계로 해외 발사체의 배관 연결부를 조사하였고, 그 결과를 토대로 몇가지 대표 형상을 선정하여 유동해석을 수행하였다. 유동해석 결과 배관의 연결부 중 제일 유동특성이 좋은 것을 찾을 수 있었다, 하지만 큰 차이는 없었다. 그 이유는 배관이 길어서 배관 내부를 유체가 흐르면서 배관 내부 유동이 안정되는 것으로 판단된다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 A
• /
• pp.285-288
• /
• 2000

This paper presents a technique for contingency ranting using line capacity calculation method and outage distribution factors(LODF) which are established by generation shift distribution factors from DC load flow solutions. By using the LODF, the line flow can be calculated a ccording to the modification of base load flow if the contingency occur. To obtain contingency ranting, maximum power tansferred to the load is obtained when load impedance $Z_r$ equal to line impedance $Z_s$. ( $Z_r$/ $Z_s$=1) The proposed algorithm has been validated in tests on a 6-bus test system.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 학술대회 논문집 전문대학교육위원
• /
• pp.95-98
• /
• 2000

This paper presents a technique for contingency ranking using line capacity calculation method and outage distribution factors (LODF) which are established by generation shift distribution factors from DC load flow solutions. By using the LODF, the line flow can be calculated a ccording to the modification of base load flow if the contingency occur. To obtain contingency ranking, maximum power tansferred to the load is obtained when load impedance $Z_r$ equal to line impedance $Z_s$. The proposed algorithm has been validated in tests on a 6-bus test system.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 C
• /
• pp.1167-1169
• /
• 1999

This paper presents the new unified power flow controller(UPFC) load flow algorithm using UPFC transmission line constant model. The UPFC transmission line constant model represents a function of transmission line constant(G.B) UPFC's effect in power system. It can easily be incorporated in a load flow program. The algorithm is suited for monitoring the power system state as well as determining the magnitude and Phase angle of UPFC serial voltage source.

• 전자공학회논문지B
• /
• 제31B권9호
• /
• pp.150-158
• /
• 1994

In this paepr, Fuzzy Constraint Line Clustering (FCLC) method for optical flow estimation is proposed. FCLC represents the spatical and temporal gradients as fuzzy sets. Based on these sets, several constraint lines with different membership values are generated for the poxed whose velocity is to be estimated. We describe the process for obtaining the membership values of the spatial and temporal gradients and that of the corresponding constraint line. We also show the process for deciding the tightest cluster of point formalated by intersection between constraint lines. For the synthetic and real images, the results of FCLC are compared with of CLC.

• 조명전기설비학회논문지
• /
• 제12권1호
• /
• pp.20-25
• /
• 1998

본 논문은 전력설비의 신속한 상정사고 선택을 위한 앨고리즘을 제시한다. 이 방법은 DC법에 의한 선로와 모선사이의 감도계수인 GSDF(Generation Shigt Distribution Factor)를 이용하여 계산되는 선로개방분배계수 (LODF : Line Outage Distribution Factor)를 사용하여 정상상태에서의 선로조류로부터 상정사고시의 선로조류를 계산하였다. 상정사고 선택을 신속히 하기 위하여 정상상태에서 용량대비 선로조류가 35〔%〕(154〔kV〕에서는 60〔%〕)이상의 선로만을 대상으로 하였다. 본 논문에서 제시한 앨고리즘 및 프로그램의 효율성을 입증하기 위하여 6모선 11선로 모델계통을 선정하여 적용하였다.

• 지능정보연구
• /
• 제2권1호
• /
• pp.93-107
• /
• 1996

A flexible flow line(FFL) consists of several groups of identical machines. All work-orders flow along the same path through successive machine groups. Thus, we emphasized the balancing of workloads between machine groups in order to maximize total productivity. On the other hand, many different types of work-orders, in varying batch or lot sizes, are produced simultaneously. The mix of work-orders, their lot sizes, and the sequence in which they are produced affect the amount of workload. However, the work-orders and their lot sizes are prefixed and cannot be changed. Because of these reasons, we have developed an optimal route selection model using heuristic search and Min-Max algorithm for balancing the workload between machine groups in the FFL.

• 한국기계가공학회지
• /
• 제17권1호
• /
• pp.95-100
• /
• 2018

This study has focused on the weld-line and birefringence reduction of a plastic optic lens using over and CAE analysis in injection compression molding. A concave lens, which has a thin thickness in the center and a large difference in thickness between the center and the periphery, often causes weld-line defects during injection molding. CAE analysis has been applied to optimize the overflow design in order to reduce the weld-line defects and the polarization defects. To reduce the weld line and birefringence defects, overflow design and application using CAE analysis show that the measured birefringence values of the specimens before the overflow application were 46.8nm and 36.9nm, and the values after the over-flow application were 13.6nm and 14.0nm. From the experimental results, it is confirmed that birefringence is greatly improved when overflow is applied.